2016 Hyundai Creta oil

7-79
7
Maintenance
Headlight, position light, turn sig
nal light, static bending light and
front fog light bulb replacement
Type A
(1) Headlight (Low/High)
(2) Parking (Position) light
(3) Front turn signal light
(4) Front fog light (if equipped)
(5) Daytime running light (if equipped)
Information
If the headlight aiming adjustment is
necessary after the headlight assembly
is reinstalled, consult an authorized
HYUNDAI dealer.i
OGS075054
•Always handle them carefully,
and avoid scratches and abra
sions. If the bulbs are lit, avoid
contact with liquids. Never touch
the glass with bare hands.
Residual oil may cause the bulb
to overheat and burst when lit. A
bulb should be operated only
when installed in a headlight.
•If a bulb becomes damaged or
cracked, replace it immediately
and carefully dispose of it.
•Wear eye protection when
changing a bulb. Allow the bulb
to cool down before handling it.Halogen bulbs
•Halogen bulbs contain pressur
ized gas that will produce flying
pieces of glass if broken.
(Continued)
(Continued)
WARNING
OLMB073042L

7-82
Maintenance
Information
If the headlight aiming adjustment is
necessary after the headlight assembly
is reinstalled, consult an authorized
HYUNDAI dealer.
Headlight (Low/High) and static
bending light replacement
1. Open the hood.
2. Remove the headlight bulb cover by turning it counterclockwise.
3. Disconnect the headlight bulb socketconnector.
4. Unsnap the headlight bulb retain ing wire by depressing the end
and pushing it upward.
5. Remove the bulb from the head light assembly.
i
•Always handle them carefully,
and avoid scratches and abra
sions. If the bulbs are lit, avoid
contact with liquids. Never touch
the glass with bare hands.
Residual oil may cause the bulb
to overheat and burst when lit. A
bulb should be operated only
when installed in a headlight.
•If a bulb becomes damaged or
cracked, replace it immediately
and carefully dispose of it.
•Wear eye protection when
changing a bulb. Allow the bulb
to cool down before handling it.Halogen bulbs
•Halogen bulbs contain pressur
ized gas that will produce flying
pieces of glass if broken.
(Continued)
(Continued)
WARNING
OLMB073042L
OGS075051
Static bending light
Turn signal
Low/High

7-90
Maintenance
•Water washing in the engine com
partment including high pressure
water washing may cause the fail
ure of electrical circuits located in
the engine compartment.
•Never allow water or other liquids to
come in contact with electrical/elec
tronic components inside the vehi
cle as this may damage them.
Waxing
Wax the vehicle when water will no
longer bead on the paint.
Always wash and dry the vehicle
before waxing. Use a good quality
liquid or paste wax, and follow the
manufacturer’s instructions. Wax all
metal trim to protect it and to main
tain its luster.
Removing oil, tar, and similar materi
als with a spot remover will usually
strip the wax from the finish. Be sure to
rewax these areas even if the rest of
the vehicle does not yet need waxing.
•Wiping dust or dirt off the body with
a dry cloth will scratch the finish.
•Do not use steel wool, abrasive
cleaners, or strong detergents con
taining highly alkaline or caustic
agents on chromeplated or
anodized aluminum parts. This may
result in damage to the protective
coating and cause discoloration or
paint deterioration.
Finish damage repair
Deep scratches or stone chips in the
painted surface must be repaired
promptly. Exposed metal will quickly
rust and may develop into a major
repair expense.
Information
If your vehicle is damaged and
requires any metal repair or replace
ment, be sure the body shop applies
anticorrosion materials to the parts
repaired or replaced.
NOTICE
i
NOTICE
OLMB073082

7-94
Maintenance
Keep your garage dry
Don't park your vehicle in a damp,
poorly ventilated garage. This cre
ates a favorable environment for cor
rosion. This is particularly true if you
wash your vehicle in the garage or
drive it into the garage when it is still
wet or covered with snow, ice or
mud. Even a heated garage can con
tribute to corrosion unless it is well
ventilated so moisture is dispersed.
Keep paint and trim in good condi
tion
Scratches or chips in the finish
should be covered with "touchup"
paint as soon as possible to reduce
the possibility of corrosion. If bare
metal is showing through, the atten
tion of a qualified body and paint
shop is recommended.
Bird droppings : Bird droppings are
highly corrosive and may damage
painted surfaces in just a few hours.
Always remove bird droppings as
soon as possible.
Don't neglect the interior
Moisture can collect under the floor
mats and carpeting and cause corro
sion. Check under the mats periodi
cally to be sure the carpeting is dry.
Use particular care if you carry fertil
izers, cleaning materials or chemi
cals in the vehicle.
These should be carried only in
proper containers and any spills or
leaks should be cleaned up, flushed
with clean water and thoroughly
dried.Interior care
Interior general precautions
Prevent chemicals such as perfume,
cosmetic oil, sun cream, hand clean
er, and air freshener from contacting
the interior parts because they may
cause damage or discoloration. If
they do contact the interior parts,
wipe them off immediately. See the
instructions that follow for the proper
way to clean vinyl.
Never allow water or other liquids to
come in contact with electrical/ elec
tronic components inside the vehicle
as this may damage them.
When cleaning leather products
(steering wheel, seats etc.), use neu
tral detergents or low alcohol content
solutions. If you use high alcohol
content solutions or acid/alkaline
detergents, the color of the leather
may fade or the surface may get
stripped off.
NOTICE
NOTICE

7-95
7
Maintenance
Cleaning the upholstery and interi
or trim
Vinyl
Remove dust and loose dirt from
vinyl with a whisk broom or vacuum
cleaner. Clean vinyl surfaces with a
vinyl cleaner.
Fabric
Remove dust and loose dirt from fab
ric with a whisk broom or vacuum
cleaner. Clean with a mild soap solu
tion recommended for upholstery or
carpets. Remove fresh spots imme
diately with a fabric spot cleaner. If
fresh spots do not receive immediate
attention, the fabric can be stained
and its color can be affected. Also, its
fireresistant proper ties can be
reduced if the material is not proper
ly maintained.
Using anything but recommended
cleaners and procedures may affect
the fabric’s appearance and fire
resistant properties.
Cleaning the lap/shoulder belt
webbing
Clean the belt webbing with any mild
soap solution recommended for
cleaning upholstery or carpet. Follow
the instructions provided with the
soap. Do not bleach or redye the
webbing because this may weaken it.
Cleaning the interior window glass
If the interior glass surfaces of the
vehicle become fogged (that is, cov
ered with an oily, greasy or waxy
film), they should be cleaned with
glass cleaner. Follow the directions
on the glass cleaner container.
Do not scrape or scratch the inside
of the rear window. This may result
in damage to the rear window
defroster grid.
NOTICE
NOTICE

8-5
8
Specifications & Consumer information
rECommENDED lubrICaNtS aND CapaCItIES
To help achieve proper engine and powertrain performance and durability, use only lubricants of the proper quality.
The correct lubricants also help promote engine efficiency that results in improved fuel economy.
These lubricants and fluids are recommended for use in your vehicle.
LubricantVolumeClassification
Engine oil * 1
*2
(drain and refill)
Recommends Gamma 1.6
3.6
l(3.8 US qt.)
ACEA A5*3
(or above)
U2 1.4/U2 1.65.3 l(5.6 US qt.)ACEA B4* 4
Manual transaxle fluid Gamma 1.6
1.6~1.7
l
(1.7~1.8 US qt.) HK MTF 70W (SK)
SPIRAX S6 GHME 70W (H.K.SHELL) GS MTF HD 70W (GS CALTEX)
(HYUNDAI genuine transaxle fluid)
U2 1.4/U2 1.6 1.7~1.9
l
(1.9~2.0 US qt.)
Automatic transaxle fluid Gamma 1.6
7.3
l(7.71 US qt.) MICHANG ATF SPIV,
SK ATF SPIV,
NOCA ATF SPIV,
HYUNDAI genuine ATF SPIV
U2 1.6
7.1
l(7.5 US qt.)
Coolant Gamma 1.6
M/T
5.7
l(6.0 US qt.)
Mixture of antifreeze and water
(Phosphatebased Ethylene glycol coolant for aluminum radiator)
A/T
5.5
l(5.8 US qt.)
U2 1.4 M/T 7.2
l(7.6 US qt.)
U2 1.6 M/T
7.2
l(7.6 US qt.)
A/T 7.0
l(7.4 US qt.)
M/T : Manual transaxle
A/T : Automatic transaxle

8-6
Specifications & Consumer information
LubricantVolumeClassification
Brake/Clutch fluid 0.7~0.8
l
(0.74~0.85 US qt.) FMVSS116 DOT3 or DOT4
Fuel55
l(58.12 US qt.)
*1
: Refer to the recommended SAE viscosity numbers on the next page.
* 2
: Engine oils labeled Energy Conserving Oil are now available. Along with other additional benefits, they contribute to fuel econ
omy by reducing the amount of fuel necessary to overcome engine friction. Often, these improvements are difficult to measure
in everyday driving, but in a year’s time, they can offer significant cost and energy savings.
* 3
: If the ACEA A5 engine oil is not available in your country, you are able to use API SM & ILSAC GF4 or above (Except Middle
East).
* 4
: If the ACEA B4 engine oil is not available in your country, you are able to use API CH4 or above.

8-7
8
Specifications & Consumer information
Recommended SAE viscosity
number
Engine oil viscosity (thickness) has
an effect on fuel economy and cold
weather operating (engine start and
engine oil flowability). Lower viscosi
ty engine oils can provide better fuel
economy and cold weather perform
ance, however, higher viscosity
engine oils are required for satisfac
tory lubrication in hot weather. Using
oils of any viscosity other than those
recommended could result in engine
damage. When choosing an oil, consider the
range of temperature your vehicle
will be operated in before the next oil
change.
Proceed to select the recommended
oil viscosity from the chart.
Always be sure to clean the area
around any filler plug, drain plug,
or dipstick before checking or
draining any lubricant. This is
especially important in dusty or
sandy areas and when the vehicle
is used on unpaved roads.
Cleaning the plug and dipstick
areas will prevent dirt and grit from
entering the engine and other
mechanisms that could be dam
aged.
CAUTION
Temperature Range for SAE Viscosity Numbers
Temperature°C
(°F) 3 0 2 0 1 0 0 1 0 2 0 3 0 4 0 5 0
1 0 0 2 0 4 0 6 0 8 0 1 0 0 1 2 0
Diesel
Engine Oil
5W30
15W40
10W30
0W30
* 1
: For better fuel economy, it is recommended to use the engine oil of a viscosity grade SAE 5W
20 (Except Middle East) or 5W30 (For Middle East). However, if the engine oil is not available in
your country, select the proper engine oil using th e engine oil viscosity chart.
* 2
: For middle East, do not use engine oil of viscosi ty grade SAE 5W20.
Gasoline
Engine Oil * 1
20W50
10W30
15W40
5W20*2, 5W30
20W50
10W30
15W40
5W30, 5W40
Except
Middle East
For
Middle East