2016 HONDA CIVIC COUPE Quick Guide

122 || 123
HANDLING THE UNEXPECTED
HANDLING THE UNEXPECTED
Replacing the Flat Tire
1. Remove the wheel nuts and at tire.
2. Mount the compact spare tire. Replace the
wheel nuts, and lightly tighten them.
3. Lower the vehicle and remove the jack. Tighten the wheel nuts in the order indicated in the image. Go around, tightening the nuts, two to
three times in this order. Do not overtighten the wheel nuts.
Models with wheel covers: Make sure the wire
support ring is hooked into the clips around the edge
of the wheel cover. Align the valve mark on the wheel cover to the tire
valve on the wheel, then install the wheel cover. If you drive with the spare tire installed, the low tire pressure/TPMS indicator appears. The indicator stays on until a regular tire is installed.
spilC
spilC
Valve mark
Storing the Flat Tire
1. Remove the center cap, if necessary.
2. Open the trunk. Place the at tire face down in
the spare tire well.
3. Remove the spacer cone from the wing bolt, ip it over, and insert it back on the bolt. Secure the at tire with the wing bolt.
4. Models with wheel covers: Make sure the wire
support ring is hooked into the clips around the
edge of the wheel cover.
5. Securely put the jack and wheel nut wrench back in the tool case. Store the case in the trunk.
Loose items can y around the interior in a crash and can seriously injure the occupants. Store the wheel, jack, and tools securely before driving.
WARNING
Spacer cone Wing bolt
For compact
spare tireFor full -
size tire
Tire valv e
Wire support rin g

124 || 125
HANDLING THE UNEXPECTED
HANDLING THE UNEXPECTED
Fuse Locations
If any electrical devices are not working, turn the vehicle off and check to see if any
applicable fuse is blown. Fuse locations are shown on the fuse box cover. Locate the
fuse in question by the fuse number and box cover number.
Engine Compartment Fuse Box
Located under the hood near the battery. Push the tabs to open the box.
AmpsCircuit Protected
1(6 0A )Cooling Fa n*2(30A )Cooling Fa n*3(50A )
IG Main*4
30
AHeadlight High Beam Main 30A
Battery12 5A
2EPS
IG Main 70
A
30 A*4
50A*5
Fuse Box Option*(40A )
Fuse Box60 A30A
Front Wiper Motor
3
Starter Motor*4

Headlight Low Beam Mai
n
Rear Defroster 40A
30 A
Fuse Box 40AABS/VSA Motor40A
ABS/VSA FSR40 ABlower Motor
4 40
A


30 A
*1:M odels with the smart entry system have
* * an
ENGINE START/STO P button
instead of an ignition switch .
2: 2.0L engine models
* 3:
1.5L engine models
** 4:
Models with smart entry system
5:Models without smart entry system
models
56:
Continuously variable transmissio n
Cooling Fan5A
6Wa sher 15A
7FI Main8 15
A15 A
S
FI ub
9Stop Lights 10A
10 Injector*3(15 A)
11LA F5A
12 FI ECU10A
13Parking Lights
14 10
A
Hazard15 A
15IG Coil16 15
A
Transmission*6(15 A)17 Daytime Running Lights 10A
18 Back Up10A
19
20 15
A(30 A)
2110 A
Circuit Protected
Audio
Audio AM P*
Interior Lights Amps22(15 A)
23Front Fog Lights*
A/C Compressor
24 (10 A)
Horn10 A25 Left Headlight Low Beam 10A
27VB ACT*326 Right Headlight Low Beam
(10 A)
10A
28 Left Headlight High Beam
30 31
29Right Headlight High Beam 10A
32 (15 A)(2
0A )
33
34 (20 A)
35
36


10
A
Interior Fuse Box
Located under the dashboard on the driver’s side.
Circuit Protected Amps110A
2(5 A)
3
4(5 A)(10 A)
510 A610A
710 A
815 A
Accessory

Key Lock
*2

Front Sensor Camera*1
Transmission*2, *3
Optio n
SRS Indicator
Meter
Fuel Pump
Fuse label
* *1: Models with smart entry syste m
*2:Models without smart entry syste m
models
9AIRCON
3: Continuously variable transmission
10 A
1011Engine Control 5A12Passenger Side Door Lock 10A13(10 A)
14(20 A)
15Front Passenger’s Side Power Window20A
16Door Loc k20A
17Transmissio n*1, *3(10
A)
(5 A)
Front Sensor Camera *2
18
19Moonroo f*20 (20
A)21ACG10A10A
22 Daytime Running Light s
2324Front Sensor Camera *(5 A)
25Driver’s Door Lock10 A
2726Passen ger Side Door Unlock10A(20 A)28 Driver’s Power Window 20A
AmpsCircuit Protecte d

126 || 127
MAINTENANCE
HANDLING THE UNEXPECTED
Inspecting and Changing Fuses
1. Turn the vehicle off, including all lights and
accessories.
2. Remove the fuse box cover.
3. Check the large fuse in the engine compartment.
4. If the fuse is blown, use a Phillips-head screwdriver to remove the screws and replace the fuse with a new one. Reinstall the screws.
5. Inspect the small fuses in the engine compartment and the vehicle interior.
6. If there is a burned out fuse, remove it with the fuse puller and replace it with a new one.Blown fuse
Combined fuse
Fuse puller
Replacing a fuse with one that has a higher rating greatly increases the chances of damaging the electrical system.
NOTICE
MAINTENANCE
Learn about basic maintenance that you can perform on the vehicle yourself, as well as information about how to best maintain the vehicle.
Safety Precautions
Some of the most important safety precautions are listed below; however, we cannot warn you of every conceivable hazard that can arise in performing maintenance. Only you can decide whether or not you should perform a given task.
Maintenance Safety
•  To reduce the possibility of re or explosion, keep cigarettes, sparks, and ames
away from the battery and all fuel-related parts.
•  Never leave rags, towels, or other ammable objects under the hood.
•  To clean parts, use a commercially available degreaser or parts cleaner, not
gasoline.
•  Wear eye protection and protective clothing when working with the battery or
compressed air.
•  Do not run the engine in conned spaces where carbon monoxide gas can
accumulate.
Vehicle Safety
•  The vehicle must be stationary, and parked on level ground with the parking brake
set and the engine off.
•  Be aware that hot parts can burn you.
•  Be aware that moving parts can injure you.
Improperly maintaining this vehicle or failing to correct a problem before driving can cause a crash in which you can be seriously hurt or killed. Always follow the inspection and maintenance recommendations according to the schedules in this guide.
WARNING
Failure to properly follow maintenance instructions and precautions can cause you to be seriously hurt or killed. Always follow the procedures and precautions in this guide.
WARNING

128 || 129
MAINTENANCE
MAINTENANCE
Maintenance Minder™
Reminds you when indicated maintenance service is due.
Models with information display
When maintenance is due, the Maintenance Minder indicator comes on and a message
appears on the display every time you turn the vehicle on. Press the TRIP knob in the instrument panel to change displays (see page 28).
Models with Driver Information Interface
When maintenance is due, the system message indicator comes on and a message
appears on the display every time you turn the vehicle on. Press the display/information button on the steering wheel to change displays (see page 29).
Maintenance Minder message
Maintenance
Minder indicator
Sub items
Main item
Maintenance Minder message
System message

indicator
Sub items
Main item
U.S. models
Maintenance, replacement, or repair of emissions control devices and systems may be done by any automotive repair establishment or individuals using parts that are
certied to EPA standards. According to state and federal regulations, failure to perform maintenance on the
maintenance main items marked with # will not void your emissions warranties.
However, all maintenance services should be performed in accordance with the intervals indicated by the Driver Information Interface.
Maintenance Minder Service Codes
These codes indicate what services are due on your vehicle.
U.S. models
*1: If a Maintenance Minder indicator does not appear more than 12 months after the display is
reset, change the engine oil every year.
#: See information on maintenance and emissions warranty.
CODEMaintenance Main Items
A 
Replace engine oi l*1
B
Replace engine oi l*1
and oil lter
 Inspect front and rear brakes
 Inspect these items:
• Tie rod ends, steering gear box, and boots
•S uspension components
• Driveshaft boots
• Brake hoses and lines (including ABS/VSA)
• All uid levels and condition of uids
• Exhaust system #
•F uel lines and connection s#
*2:If you drive in dusty conditions, replace the air cleaner element every 15,000 miles (24,000 km).*3:If you drive primarily in urban areas that have high concentrations of soot in the air from industryand diesel-powered vehicles, replace the dust and pollen lter every 15,000 miles (24,000 km).*4:Driving in mountainous areas at very low vehicle speeds results in higher transmission
temperatures. This requires transmission uid changes more frequently than recommended by
the Maintenance Minder. If you regularly drive your vehicle under these conditions, have the
transmission uid changed every 25,000 miles (40,000 km).
CODEMaintenance Sub Items
1 
Rotate tires
2
Replace air cleaner element *2
 Replace dust and pollen lter *3
 Inspect drive belt
3 
Replace transmission uid *4
4
Replace spark plug s
 Inspect valve clearance
5 
Replace engine coolant
7Replace brake uid*5
*5:If a Maintenance Minder indicator does not appear more than 36 months after the display for item 7 is reset, change the brake uid every 3 years.
In addition: •  Inspect idle speed every 160,000 miles (256,000 km).
•  Adjust the valves during services A, B, 1, 2, or 3 if they are noisy.

130 || 131
MAINTENANCE
MAINTENANCE
*1: If a Maintenance Minder message does not appear more than 12 months after the display is
reset, change the engine oil every year.
*2: If you drive in dusty conditions, replace the air cleaner element every 24,000 km (15,000 miles). *3:
If you drive primarily in urban areas that have high concentrations of soot in the air from industryand diesel-powered vehicles, replace the dust and pollen lter every 24,000 km (15,000 miles).
*4: Driving in mountainous areas at very low vehicle speeds results in higher transmission
temperatures. This requires transmission uid changes more frequently than recommended by
the Maintenance Minder. If you regularly drive your vehicle under these conditions, have the
transmission uid changed every 40,000 km (25,000 miles).
*5: If a Maintenance Minder Indicator does not appear more than 36 months after the display for
item7 is reset, change the brake uid every 3 years.#:See information on maintenance and emissions warranty.
CODEMaintenance Main Items
A 
Replace engine oi l*1
0
Replace engine oi l*1
and oil lte r
CODEMaintenance Sub Items
1 
Rotate tires
2Replace air cleaner element *2
 Replace dust and pollen lte r*3
 Inspect drive belt
3 
Replace transmission uid *4
4
Replace spark plugs
 Inspect valve clearance
5 
Replace engine coolant
7
Replace brake uid *5
9 
Service front and rear brakes
 Inspect these items:
•T ie rod ends, steering gearbox, and boots
•S uspension components
•D riveshaft boots
•B rake hoses and lines (including ABS/VSA)
•A ll uid levels and condition of uid s
•E xhaust system #
•F uel lines and connections #
Canadian models
In addition: • 
Inspect idle speed every 256,000 km (160,000 miles).
•  Adjust the valves during services A, 0, 1, 2, 3, or 9 if they are noisy.
Under the Hood
1.5 ℓ engine models
Brake fluid (black cap)
Reserve tank
Washer fluid (blue cap) Engine oil dipstick (orange)
Engine oil fill cap
Battery
Reserve tank cap
U.S. odelsWasher fluid (blue cap)

132 || 133
MAINTENANCE
MAINTENANCE
Opening the Hood
1. Park the vehicle on a level surface, and set the
parking brake.
2. Pull the hood release handle under the lower left corner of the dashboard.
3. Push the hood latch lever in the center to the right to release the lock mechanism, and open the hood.
4. Remove the support rod from the clamp using the grip. Mount the support rod in the hood.
When closing, remove the support rod, and stow it in the clamp, then gently lower the hood. Remove your hand at a height of approximately 12 inches (30 cm) and let the hood close.
Do not open the hood when the wiper arms are raised. The hood will strike the wipers, and may damage either the hood or the wipers.
NOTICE
Hood release handle
Pull
Lever
Support rodGrip
Clamp
Engine Oil
Park the vehicle on level ground, and wait approximately three minutes after turning the engine off before you check the oil.
Checking the Oil
1. Remove the dipstick (orange).
2. Wipe the dipstick with a clean cloth or paper towel.
3. Insert the dipstick back all the way into its hole.
4. Remove the dipstick again, and check the level. It should be between the upper and lower
marks. Add oil if necessary. 1.5 ℓ engine models
Upper mark Lower mark
1.5 ℓ engine models
Upper mark Lower mark
2.0 ℓ engine models
2.0 ℓ engine models
CAUTION
The hood support rod can become hot and burn your hand. Always grip the rod using the foam area.

134 || 135
MAINTENANCE
MAINTENANCE
Recommended Engine Oil
•  Honda Genuine Motor Oil
•  Premium-grade 0W-20 detergent oil with an API Certication Seal on the
container
This seal indicates the oil is energy conserving and
that it meets the American Petroleum Institute’s latest requirements. Use Honda Genuine Motor Oil or another commercial engine oil of suitable viscosity for the ambient temperature as shown.
You may also use synthetic motor oil if it is labeled with the API Certication Seal and is of the specied viscosity grade.
Adding Oil
1. Unscrew and remove the engine oil ll cap.
2. Add oil slowly.
3. Reinstall the engine oil ll cap, and tighten it securely.
4. Wait for three minutes and recheck the engine oil dipstick.
Ambient temperature
Engine oil ll cap
1.5 ℓ engine models
Engine oil ll ca p
2.0 ℓ engine models
Do not ll the engine oil above the upper mark. Overlling the engine oil can result in leaks and engine damage.
NOTICE
Resetting the Engine Oil Life
If you change or replace the vehicle’s engine oil yourself, you must reset the engine oil life.
Models with information display
1. Press the TRIP knob in the instrument panel until
the engine oil life appears in the display.
2. Press and hold the knob for 10 seconds or more, until the display begins to blink.
3. Press and hold the knob for 5 seconds or more. The engine oil life display returns to 100%.
Models with Driver Information Interface
Use the steering wheel buttons to make and enter selections (see page 29).
1. Scroll to the Maintenance Minder screen, and select it.
2. Press and hold the ENTER button for about 10 seconds to enter the reset mode.
3. Scroll to the maintenance item you want to reset (or All Due Items), and select it.
Models with Display Audio
Use the touchscreen to make and enter selections.
1. From the HOME screen, select Settings.
2. Select Vehicle.
3. Select Maintenance Info.
4. Select Select Reset Items.
5. Select an item on the list to reset.
Failure to reset the engine oil life after a maintenance service results in the system showing incorrect maintenance intervals, which can lead to serious mechanical problems.
NOTICE

136 || 137
MAINTENANCE
MAINTENANCE
Engine Coolant
Park the vehicle on level ground. Check the reserve tank and the coolant level in the
radiator. We recommend Honda Long Life Antifreeze/Coolant Type 2.
Checking the Coolant
1. Check the amount of coolant in the reserve tank.
2. If the coolant level is below the MIN mark, add
the specied coolant until it reaches the MAX mark.
3. Inspect the cooling system for leaks.
Adding Coolant
1. Make sure the engine and radiator are cool.
2. Turn the reserve tank cap counterclockwise and relieve any pressure in the coolant system. Do not push the cap down when turning.
3. Push down and turn the reserve tank cap counterclockwise to remove it.
4. Pour coolant into the reserve tank until it reaches the MAX mark.
5. Put the reserve tank cap back on, and tighten it fully.
If temperatures consistently below 22°F (30°C) are expected, the coolant mixture should be changed to a higher concentration. Consult a dealer for details for more information.
NOTICE
Reserve tank cap
1.5 ℓ engine models
Reserve tank cap
2.0 ℓ engine models
Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you. Always let the engine and radiator cool down before removing the radiator cap.
WARNING
Pour the uid slowly and carefully so you do not spill any. Clean up any spills immediately; they can damage components in the engine compartment.
NOTICE
MA X
MINReserve tan k
Window Washer Fluid
Check the amount of window washer uid by looking
at the reservoir. If the washer uid level is low, ll the
washer reservoir.
Pour the washer uid carefully. Do not overow the
reservoir.
Canadian models
If the washer uid level is low, the washer level indicator or a message appears in the Driver Information Interface.
Do not use engine antifreeze or a vinegar/water solution in the windshield washer
reservoir. Antifreeze can damage your vehicle’s paint. A vinegar/water solution can damage the windshield washer pump.
NOTICE
Brake/Clutch* Fluid
The uid level should be between the MIN and MAX marks on the side of the reservoir.
We recommend using Honda Heavy Duty Brake Fluid DOT 3.
Pour the uid carefully.If the uid level is at or below the MIN mark, have a dealer inspect for leaks or worn brake pads as soon as possible.
The brake uid reservoir is also used for your vehicle’s clutch uid. As long as you keep the brake uid level as instructed above, there is no need for checking the clutch uid level.Brake uid marked DOT 5 is not compatible with your vehicle’s braking system and can cause extensive damage.
NOTICE
Brake reservoir
MINMAX
*if equipped