2016 Citroen DS5 Owner's Manual

127
DS5_en_Chap04_conduite_ed02-2015
F With the engine running, press button 1. The
activated/deactivated status when the engine was
switched off is retained when the engine is switched
on again.
The blade retracts automatically 3 seconds after switching
off the engine except in STOP mode of Stop & Start.
Activation / dea ctivation
F With the engine running, adjust the
b
rightness of the information using
button
3 :
- to

wards the rear to increase the
brightness,
-
to

wards the front to decrease the
brightness.
Brightness adjustment
We recommend that adjustments are
only made using these buttons when
the vehicle is stationary.
When stationary or while driving, no
objects should be placed around the
transparent blade (or on its cover) to
avoid blocking deployment of the blade
and preventing its correct operation.
In certain extreme weather conditions
(rain and/or snow, bright sunshine, ...)
the head-up display may not be legible
or may suffer temporary inter ference.
Some sunglasses may hamper reading
of the information.
To clean the transparent blade, use a
clean, soft cloth (such as a spectacles
cloth or microfibre cloth). Do not use
a dry or abrasive cloth or detergent or
solvent products as these could scratch
the blade or damage the anti-reflection
coating.
Height adjustment
F With the engine running, adjust the display
t o the required height using button 2 :
-
to

wards the rear to move the display up,
-
to

wards the front to move the display
down.
driving

DS5_en_Chap04_conduite_ed02-2015
Memorising speeds
Activating the function
Modifying a speed setting
With your Audio system
"MEM" button
F Press this button to display the list of
memorised speed settings.
By offering preset speed settings, this function facilitates the programming of a speed setting for both the speed limiter and the cruise
control.
The system includes up to 5 or 6 speeds, depending on equipment, that you can modify.
As a safety measure, the driver must
only modify the speed settings when
stationary.
F
Go t

o the main menu by pressing the
"MENU" button:
F Selec
t the"Personalisation-configuration"
menu and confirm.
F
Se

lect " Vehicle parameters" menu and
confirm.
F
Se

lect the "Driving assistance" line and
conform.
F
Se

lect "Speeds memorised" line and
confirm.
F
Se

lect "Activation" to activate the function. F
Se

lect the speed setting to be modified and
confirm.
F Mo
dify the speed setting.
F
Selec

t " OK " and confirm to save the
modifications.

129
DS5_en_Chap04_conduite_ed02-2015
With the touch screen
F Press this button to select the
"driving" menu.
F
Pr

ess "Speed settings ".
F
Se

lect the system for which you want to
memorise new speed settings:
F
Ch

oose the speed setting to be modified. F
En

ter the new value using the numerical
keypad and confirm.
F
Co

nfirm to save the modification and quit
the menu.
"MEM" button
This button allows you to select a speed setting
to be used with the speed limiter or cruise
control.
Refer to the corresponding section.
Modifying a speed setting
● speed limiter
or
●
cr

uise control
driving

DS5_en_Chap04_conduite_ed02-2015
6. Speed limiter on / pause indication.
7. Sp
eed limiter mode selection indication.
8.
Pr

ogrammed speed value.
9.
Se

lection of a memorised speed setting.
displays in the instrument panel
Speed limiter
The speed limiter is a driving aid that
cannot, in any circumstances, replace the
need to observe speed limits or the need
for vigilance on the part of the driver. 1.
Sp

eed limiter mode selection wheel.
2.
Pr
ogrammed value decrease button.
3.
Pr
ogrammed value increase button.
4.
Sp
eed limiter on / pause button.
5.
Di
splay memorised speed settings button.
Steering mounted controls
This information also appears in the
head-up display.
For more information, refer to the
"Head-up display" section.
System which prevents the vehicle from exceeding the speed programmed by the driver.
The speed limiter is switched on
manually.
The minimum programmed speed is
20
m

ph (30 km/h).
The programmed speed remains in the
system memory when the ignition is
switched off.

131
DS5_en_Chap04_conduite_ed02-2015
F Turn the wheel 1 to the "LIMIT" p osition
to select the speed limiter; the function is
paused.
F
If t

he speed setting is suitable (last speed
setting programmed in the system) press
button 4 to switch the speed limiter on.
Switching on Adjusting the limit speed
setting
F Pressing button 4 temporarily interrupts the
f
unction (pause). You do not have to switch the speed limiter on
in order to set the speed.
To modify the limit speed setting from the
current speed of the vehicle:
F
in s
teps of +/- 1 mph (km/h), make
successive short presses on button 2 or 3 ,
F
co
ntinuously, in steps of +/- 5 mph (km/h),
press and hold button 2 or 3 .
To modify the limit speed setting using
memorised speeds and from your Audio
system:
F
wi
th the system first activated.
For more information on memorising speeds,
refer to the corresponding section.
F
ma
ke a long press on button 2 or 3
, the
system displays the memorised speed
closest to the actual speed of the vehicle;
this setting becomes the new limit speed,
F
to c
hoose another memorised speed, make
another long press on button 2 or 3.
To modify the limit speed setting using
memorised speeds and from the touch screen:
F
pr
ess button 5 to display the six memorised
speed settings,
F
pr
ess the button for the desired speed
setting.
This setting becomes the new limit speed.
driving

DS5_en_Chap04_conduite_ed02-2015
Temporarily exceeding the
programmed speedSwitching off
Operating fault
The use of mats not approved by
CITROËN may inter fere with the
operation of the speed limiter.
To avoid any risk of jamming of the
pedals:
-
en

sure that the mat is positioned
c o r r e c t l y,
-
do n

ot fit one mat on top of another.
F
If y

ou want to temporarily exceed the
programmed limit speed, press firmly
o

n
the accelerator pedal, going beyond the
point of resistance .
The speed limiter is deactivated temporarily
and the displayed programmed speed flashes. F
Tu

rn wheel 1 to the "0"
position: the
display of information on the speed limiter
disappears. Flashing dashes indicate a fault with the speed
limiter.
On a steep descent or in the event of
sharp acceleration, the speed limiter
will not be able to prevent the vehicle
from exceeding the programmed speed.
When the limit speed is exceeded but is not
due to action by the driver, there is an audible
signal to complete the alert.
Once the speed of the vehicle returns to
the programmed setting, the speed limiter
functions again: the display of the programmed
speed setting becomes steady again. Have it checked by a CITROËN dealer or a
qualified workshop.

133
DS5_en_Chap04_conduite_ed02-2015
The cruise control system is a driving aid
that cannot, in any circumstances, replace
the need to observe speed limits, nor the
need for vigilance on the part of the driver.
Cruise control
1. Cruise control mode selection wheel.
2. Bu tton for setting the current speed of the
vehicle as the cruise setting or lowering the
cruise setting.
3.
Bu

tton for setting the current speed of the
vehicle as the cruise setting or raising the
cruise setting.
4.
Cr

uise control pause / resume button.
5.
Di

splay memorised speed settings button.
Steering mounted controls
6. Cruise control pause / resume indication.
7. Cr uise control mode selected indication.
8.
Cr

uise speed setting.
9.
Se

lecting a memorised cruise speed.
displays in the instrument panelThe cruise control is switched on
manually.
It requires a minimum vehicle speed of
25 mph (40 km/h) as well as:
-
wi

th a manual gearbox, the
engagement of fourth gear or
higher,
-
wi

th an automatic gearbox, the gear
selector at position
d o

r second
gear or higher in manual mode.
This information also appears in the
head-up display.
For more information, refer to the
"Head-up display" section.
System which automatically maintains the cruising speed of the vehicle at a setting programmed by the driver, without any action on the accelerator
pedal.
Switching off the ignition cancels any
programmed speed setting.
The operation of the cruise control can be
interrupted (pause):
-
by p

ressing control 4 or by pressing the
brake or clutch pedal,
-
au

tomatically, if operation of the dynamic
stability control system is triggered.
As a safety measure, you are advised
to keep your feet near the pedals at all
times.
driving

DS5_en_Chap04_conduite_ed02-2015
F Turn the wheel 1 to the "cRUISE" position
to select cruise control mode; the function
is paused.
F
To s

tart the cruise control and set a cruise
speed, once the vehicle has reached the
desired speed, press button 2 or 3 : the
current speed of your vehicle becomes the
cruise speed setting.
Yo

u can release the accelerator pedal.
Switching on
F Pressing button 4 interrupts operation of
the system (pause).
F
Pr

essing button 4 again restores operation
of the cruise control (ON).
Adjusting the cruise speed
setting
The cruise control must be activated. As a precaution, it is recommended
that the cruise speed chosen be close
to the current speed of your vehicle, so
as to avoid any sudden acceleration or
deceleration of the vehicle.
To modify the cruise speed setting from the
current speed of the vehicle:
F
in s

teps of + or - 1 mph (km/h), make
repeated short presses on button 2 or 3 ,
F
co

ntinuously, in steps of + or - 5 mph
(km/h), press and hold button 2 or 3 .
Take care: pressing and holding
button
2

or 3
r
esults in a rapid change
in the speed of your vehicle.
To modify the cruise speed setting using
memorised speeds and from your Audio
system:
F
wi

th the system first activated.
For more information on memorising speeds,
refer to the corresponding section.
F
ma

ke a long press on button 2 or 3 , the
system displays the memorised speed
closest to the actual speed of the vehicle;
this setting becomes the new cruise speed,
F
to c

hoose another memorised speed, make
another long press on button 2 or 3. To modify the cruise speed setting using
memorised speeds and from the touch screen:
F
pr

ess button 5 to display the six memorised
speed settings,
F
pr
ess the button for the desired speed
setting.
This setting becomes the new cruise speed.