There is a risk of damage to the gearbox:
- i f you press the accelerator and
b
rake pedals at the same time,
-
i
f you force the movement of the
s
elector from the P position to
another position when the battery
is
flat.
To
reduce fuel consumption when at
a
prolonged standstill with the engine
r
unning (traffic jam...), put the selector
i
n the n position and apply the parking
b
rake.
If the selector is not in position P
,
when
the
driver's
door
is
opened
or
a
pproximately
45
seconds
after
the
i
gnition
is
switched
off,
a
warning
m
essage
appears
in
the
screen.
F
R
eturn the selector to position P ;
t
he
message
disappears.
When
driving
on
flooded
roads
or
when
c
rossing
a
ford,
proceed
at
walking
p
ace.
Operating fault
Manual operation
When the ignition is on, the lighting o
f this warning lamp, accompanied
b
y
an
audible signal and a message in the
m
ultifunction screen, indicates a gearbox fault.
In
this
case, the gearbox switches to back-up
m
ode
and
is locked in 3rd gear. You may feel
a
substantial knock when changing from P
to R
and
from n to R .
This will not cause any
d
amage
to
the gearbox.
Do
not
exceed 60 mph (100 km/h), local speed
r
estrictions
p
ermitting.
Contact
a
CITROËN dealer or a qualified
w
orkshop
as soon as possible.
F
Sel
ect position M for sequential c
hanging o
f
the
four
gears.
F
P
ush
the
selector
towards
the
+
sign
to
c
hange
up
a
gear.
F
P
ull
the
selector
towards
the
-
sign
to
c
hange
down
a
gear.
It
is
only
possible
to
change
from
one
gear
to
a
nother
if
the
vehicle
speed
and
engine
speed
p
ermit;
other wise,
the
gearbox
will
operate
t
emporarily
in
automatic
mode. This
symbol
is
displayed
if
a
gear
i
s
not
engaged
correctly
(selector
b
etween
two
positions).
d
disappears
and
the
gears
e
ngaged
appear
in
succession
in
the
in
strument
pan
el.
Stopping the vehicle
Before switching off the engine, you can engage p osition P or
n
to place the gearbox in neutral.
In
both cases, apply the parking brake to
i
mmobilise the vehicle.
Invalid value during manual
operation
If the engine speed is too low or too high, the gear selected flashes for a few seconds, then
t
he actual gear engaged is displayed.
It
is possible to change from position d
(automatic)
to position M (manual) at any time.
When
the vehicle is stationary or moving
v
ery slowly, the gearbox selects gear M1
automatically.
The
sport and snow programmes do not
o
perate in manual mode.
11 9
Six-speed automatic gearbox which offers a choice between the comfort of fully automatic
o
peration or manual gear changing.
Two
driving modes are available:
-
a
utomatic operation with electronic
management
of the gears by the gearbox,
-
m
anual
operation for sequential changing
o
f the gears by the driver.
Automatic gearbox (EAT6)
P. Park.
- I mmobilisation of the vehicle, parking brake
o
n or off.
-
S
tarting the engine.
R.
R
everse.
-
R
eversing manoeuvres, vehicle stationary,
e
ngine at idle.
n. N
eutral.
-
I
mmobilisation of the vehicle, parking
b
rake on.
-
S
tarting the engine.
d
.
A
utomatic
ope
ration.
M + / -.
M
anual operation with sequential
c
hanging of the six gears.
F
P
ull backward to change up through the
g
ears.
or
F
P
ush for ward to change down through the
g
ears. When
you move the selector to select a
p
osition, the corresponding indicator is
d
isplayed in the instrument panel.
P.
Pa
rk
R.
Reverse
n. N
eutral
d
.
D
rive
(
Automatic
ope
ration)
1 2 3 4 5 6.
G
ears engaged during manual
ope
ration
-.
I
nvalid value during manual operation
gear selector positionsdisplays in the instrument panel
Foot on brake
F Press the brake pedal when this i
ndicator lamp is displayed in the
i
nstrument panel (e.g.: starting
t
he
eng
ine).
driving
121
F Select position d for automatic c hanging o
f the six gears.
The
gearbox then operates in auto-adaptive
m
ode, without any intervention on the part
o
f the driver. It continuously selects the most
s
uitable gear according to the style of driving,
t
he profile of the road and the load in the
v
ehicle.
For
maximum acceleration without touching
t
he selector, press the accelerator pedal down
f
ully (kick down). The gearbox changes down
a
utomatically or maintains the gear selected
u
ntil the maximum engine speed is reached.
On
braking, the gearbox changes down
a
utomatically to provide efficient engine
b
raking.
If you release the accelerator sharply, the
gearbox
will not change to a higher gear for
s
afety reasons.
Automatic operation
Never select position n while the
v ehicle is moving.
Never select positions P or R unless
the
vehicle is completely stationary.
Reverse
When selecting reverse R with the ignition on, t
he rear parking sensors are activated.
For
more information, refer to the "Rear parking
sen
sors"
se
ction.
Creep function (moving without
using the accelerator)
This function provides great flexibility in manoeuvring the vehicle at low speed (when
p
arking, in traffic jams, …).
With
the engine at idle, parking brake released
a
nd position d
,
M or R
s
elected,
t
he vehicle
moves
as soon as you take your foot off
t
he brake pedal (even without pressing the
a
ccelerator).
For
your safety, this function will be activated
o
nly if you press the brake pedal when
c
hanging from for ward drive to reverse.
It
is deactivated on opening the driver's door.
Closing
the door then pressing the brake or
a
ccelerator pedal, reactivates the function.
driving
To reduce fuel consumption when at a prolonged standstill with the engine
r
unning (traffic jam...), put the selector
i
n the n position and apply the parking
b
rake.
If the selector is not in position P
,
when
the
driver's
door
is
opened
or
a
pproximately
45
seconds
after
the
i
gnition
is
switched
off,
a
warning
m
essage
appears
in
the
screen.
F
R
eturn the selector to position P
;
t
he
message
disappears.
When
driving
on
flooded
roads
or
when
c
rossing
a
ford,
proceed
at
walking
p
ace. There
is a risk of damage to the gearbox:
-
i
f you press the accelerator and
b
rake pedals at the same time,
-
i
f you force the movement of the
s
elector from the P position to
another position when the battery
is flat.
F
Sel
ect position M for sequential
c
hanging
o
f
the
six
gears.
F
M
ove
the
selector
towards
the
+
sign
to
c
hange
up
a
gear.
F
M
ove
the
selector
towards
the
-
sign
to
c
hange
down
a
gear.
It
is
only
possible
to
change
from
one
gear
to
a
nother
if
the
vehicle
speed
and
engine
speed
p
ermit;
other wise,
the
gearbox
will
operate
t
emporarily
in
automatic
mode.
Manual operation
d disappears and the gears e
ngaged appear in succession in the
in
strument
pan
el.
If
the
engine speed is too low or too high, the
g
ear
selected flashes for a few seconds, then
t
he
actual
gear engaged is displayed.
It
is
possible to change from position d
(automatic)
to position M (manual) at any time.
When
the
vehicle is stationary or moving
v
ery
slowly, the gearbox engages first gear
au
tomatically.
Invalid value during manual
operation
This symbol is displayed if a gear i s not engaged correctly (selector
b
etween two positions).
Stopping the vehicle
Before switching off the engine, you can engage position P or n to place the gearbox in
neu
tral.
In
both cases, apply the parking brake to
i
mmobilise the vehicle. When
the ignition is on, the lighting
o
f this warning lamp, accompanied
Operating fault
by an audible signal and a message in the m
ultifunction screen, indicates a gearbox fault.
In
this case, the gearbox switches to back-up
m
ode and is locked in 3rd gear. You may feel
a
substantial knock when changing from P
to R
and from n to R.
This will not cause any
d
amage to the gearbox.
Do
not exceed 60 mph (100 km/h), local speed
r
estrictions
p
ermitting.
Contact
a CITROËN dealer or a qualified
w
orkshop as soon as possible.
123
Gear efficiency indicatorSystem which reduces fuel consumption by advising the driver to change up.
Operation
Example:
-
Y ou are in third gear.
-
Y
ou press the accelerator pedal.
-
T
he system may suggest that you engage
a
higher gear.
The
information appears in the instrument
p
anel in the form of an arrow. The
system adapts its gear change
r
ecommendation according to the
d
riving conditions (slope, load, ...) and
t
he demands of the driver (power,
a
cceleration, braking, ...).
The
system never suggests:
-
e
ngaging first gear,
-
enga
ging
r
everse
g
ear,
-
e
ngaging a lower gear.
With
an
electronic
or
automatic
g
earbox,
the
system
is
only
active
in
m
anual
m
ode.
On vehicle fitted with a manual
g
earbox, the arrow may be
a
ccompanied by the gear
re
commended.
Depending
on
the
driving
situation
and
your
v
ehicle's
equipment,
the
system
may
advise
y
ou
to
skip
one
(or
more)
gear(s).
You
can
f
ollow
this
instruction
without
engaging
the
i
ntermediate
g
ears.
The
gear
engagement
recommendations
must
n
ot
be
considered
compulsory.
In
fact,
the
c
onfiguration
of
the
road,
the
amount
of
traffic
a
nd
safety
remain
determining
factors
when
c
hoosing
the
best
gear.
Therefore,
the
driver
r
emains
responsible
for
deciding
whether
or
not
t
o
follow
the
advice
given
by
the
system.
This
function
cannot
be
deactivated.
driving
Stop & Start
Operation
going into engine STOP mode
For your comfort, during parking manoeuvres, STOP mode is not
a
vailable for a few seconds after
c
oming out of reverse gear.
Stop
& Start mode does not affect the
f
unctionality of the vehicle, such as for
example,
braking, power steering...
Never
refuel with the engine in STOP
m
ode; you must switch off the ignition
w
ith the key.
The "ECO"
warning
lamp
comes
o
n
in
the
instrument
panel
and
the
e
ngine
goes
into
standby:
-
w
ith a manual gearbox , when stationary
or
at
speeds
below
12
mph
(20
km/h)
(
depending
on
version),
when
you
put
the
g
ear
lever
into
neutral,
and
you
release
the
c
lutch
pedal.
-
w
ith a 5 or 6-speed electronic gearbox ,
when
stationary
or
at
speeds
below
5
mph
(
8
km/h)
(depending
on
version),
when
y
ou
press
the
brake
pedal
or
put
the
gear
s
elector in position
n
.
-
w
ith an automatic gearbox , vehicle
stationary,
when
you
press
the
brake
pedal
o
r
you
place
the
gear
selector
in
position
n
.
A
time
counter
calculates
t
he
sum
of
the
periods
in
S
TOP mode
during
a
journey.
I
t
rests
itself
to
zero
every
time
t
he
ignition
is
switched
on
with
t
he
key.
The
Stop
&
Start system
puts
the
engine
t
emporarily
into
standby
-
STOP
mode
-
during
s
tops
in
the
traffic
(red
lights,
traffic
jams...).
The
engine
restarts
automatically
-
START
m
ode
-
as
soon
as
you
want
to
move
off.
T
he
restart
takes
place
instantly,
quickly
and
sil
ently.
Per fect
for
urban
use,
the
Stop
&
Start
system
r
educes
fuel
consumption
and
exhaust
e
missions
as
well
as
the
noise
level
when
s
tationary.
125
going into engine START mode
The "ECO" warning lamp goes off a
nd the engine starts:
-
w
ith a manual gearbox , when you
depress
the clutch pedal,
-
w
ith an electronic or automatic
gearbox :
●
g
ear selector in position A / d or M,
when
you release the brake pedal,
●
o
r
gear selector in position n and the
b
rake pedal released, when you move
t
he
gear selector to position A / d or M,
●
o
r
when you engage reverse gear.
Special cases: START invoked
automatically
For reasons of safety and for your comfort, START mode is invoked automatically when:
-
y
ou open the driver's door,
-
y
ou unfasten the driver's seat belt,
-
t
he speed of the vehicle exceeds 7 mph
(11
km/h) with the electronic gearbox
s
ystem,
-
s
ome special conditions (battery charge,
e
ngine temperature, braking assistance,
a
mbient temperature...) where the engine is
n
eeded for control of a system.
The "ECO"
warning lamp flashes for
a
few seconds, then goes off.
This operation is perfectly normal.
With
a
manual
gearbox
in
STOP
m
ode,
if
you
engage
a
gear
without
f
ully
depressing
the
clutch
pedal,
a
m
essage
is
displayed
asking
you
to
f
ully
depress
the
clutch
pedal
so
that
t
he
engine
can
restart.
STOP
mode
is
not
invoked
when:
-
t
he
driver's
door
is
open,
-
t
he
driver's
seat
belt
is
not
fastened,
-
t
he
vehicle
has
not
exceeded
6
mph
(10
km/h)
since
the
last
engine
start
using
t
he
key,
-
t
he
engine
is
needed
to
maintain
a
c
omfortable
temperature
in
the
passenger
c
ompartment,
-
d
emisting
is
active,
-
s
ome
special
conditions
(battery
charge,
e
ngine
temperature,
braking
assistance,
a
mbient
temperature...)
where
the
engine
is
n
eeded
to
assure
control
of
a
system.
Special cases: STOP mode not
available
The "ECO" warning lamp flashes for a
few seconds then goes off.
This operation is perfectly normal.
driving
Stop & Start requires a 12 V battery with a special specification and
t
echnology.
All
work on this type of battery must
o
nly be done by a CITROËN dealer or
a
qualified workshop.
For
more information on the 12 V
b
attery, please see the corresponding
s
ection.
Operating fault
In the event of a fault with the system, the "ECO OFF" switch warning lamp flashes for a
f
ew moments then comes on continuously.
Have
it checked by a CITROËN dealer or a
q
ualified
w
orkshop.
In
the event of a fault in STOP mode, the
v
ehicle may stall. All of the instrument panel
w
arning lamps come on. It is then necessary
t
o switch off the ignition and start the engine
a
gain using the key.
Press
this
switch
to
deactivate
the
system.
The
deactivation
is
confirmed
by
the
switch
w
arning
lamp
coming
on
accompanied
by
a
m
essage.
Pressing
this
switch
again
reactivates
the
f
unction.
The
switch
warning
lamp
goes
off,
a
ccompanied
by
a
message.
In
certain
circumstances,
such
as
maintaining
a
comfortable
temperature
in
the
passenger
c
ompartment,
it
may
be
useful
to
deactivate
S
top
&
Start.
You
can
request
deactivation
at
any
time,
once
t
he
ignition
is
switched
on.
If
the
engine
is
in
STOP
mode,
it
restarts
i
mmediately.
Stop
&
Start
reactivates
automatically
each
t
ime
the
ignition
is
switched
on.
deactivation / Manual
reactivation
Opening the bonnet
dr
iving on flooded roads
Before
driving through a flooded road,
i
t is strongly recommended that you
d
eactivate the Stop & Start system.
For
more advice on driving,
p
articularly on flooded roads, refer to
t
he corresponding section.
Before
doing anything under the bonnet,
d
eactivate the Stop & Start system to
a
void the risk of injury related to an
a
utomatic change to START mode.