Page 263 of 527

261
C4-Picasso-II_en_Chap07_info-pratiques_ed01-2016
Very cold climate screen(s)*
Removable protective screens which prevent the accumulation of snow at the radiator cooling fan.
D epending on version, you will have one or two screens.
F
O
ffer up the corresponding very cold
c
limate screen to the upper or lower
section
of the front bumper.
F
P
ress around the edge of each screen to
e
ngage its fixing clips one by one.
F
U
se a screwdriver as a lever to release the
fixing
clips in turn on each screen.
Do
not forget to remove the very cold climate
s
creen(s)
w
hen:
-
t
he ambient temperature exceeds 10 °C,
-
tow
ing,
-
d
riving
a
t
s
peeds
a
bove
7
5
m
ph
(
120 km/h).
Removal Fitting
360 Vision system
The pre-cut zone must be removed
before fitting the screen to the front
b
umper, to allow operation of the
camera.
When the very cold climate screen
is
fitted, the image provided by the
c
amera is slightly different.
* Depending
on
the
country
of
sale.
7
Practical information
Page 280 of 527

278
C4-Picasso-II_en_Chap07_info-pratiques_ed01-2016
Brake wear depends on the style of driving, particularly in the case o
f vehicles used in town, over short
distances.
It may be necessary to have
t
he condition of the brakes checked,
e
ven between vehicle services.
Brake pads
For information on checking brake disc wear, contact a CITROËN dealer
or
a qualified workshop.
Brake disc wear
Only use products recommended by
CITROËN or products of equivalent
quality
an
d
sp
ecification.
In order to optimise the operation of
units as important as those in the
braking
system, CITROËN selects and
o
ffers very specific products.
After
washing the vehicle, dampness,
o
r in wintry conditions, ice can form
on
the brake discs and pads: braking
e
fficiency may be reduced. Make light
b
rake applications to dry and defrost
t
he brakes.
Electric parking brake
For more information, refer to the " Electric
parking brake - Operating faults "
section.
This system does not require any
routine
servicing. However, in the
e
vent of a problem, have the system
checked by a CITROËN dealer or a
q
ualified
w
orkshop.
Manual gearbox
The gearbox does not require any m
aintenance (no oil change).
Refer
to the manufacturer's service
s
chedule for the checking interval for
t
his
c
omponent.
Automatic gearbox
The gearbox does not require any maintenance (no oil change).
Refer
to the manufacturer's service
s
chedule for details of the level
checking
interval for this component.
To
avoid damaging the electrical units,
n
ever use a high pressure jet wash in
t
he engine compartment.
Unless
there is a leak in the circuit, a drop in
t
he brake fluid level indicates that the brake
p
ads are worn.
Practical information
Page 283 of 527

281
C4-Picasso-II_en_Chap07_info-pratiques_ed01-2016
Recommendations on storage
AdBlue® freezes at about -11°C and
deteriorates above 25°C. It is recommended
t
hat bottles be stored in a cool area and
protected
from direct sunlight.
Under
these conditions, the fluid can be kept
f
or
at
least a year.
If the additive has frozen, it can be used once it
has
completely thawed out.
Procedure
Before topping-up, ensure that the vehicle is parked on a flat and level sur face.
In wintry conditions, ensure that the
temperature
of the vehicle is above -11°C.
O
ther wise, by freezing, the AdBlue
® cannot
be
poured
into
its
tank.
Park
your
vehicle in a
w
armer area for a few hours to allow the top-up
to
be
carried
out.
F
P
ress
the
START/STOP
button
to switch
o
ff
the
engine. F
F or access to the AdBlue® tank, raise the b
oot floor, or on 7-seat versions, unfold the
right
hand
seat
in
the
third
row.
Never store bottles of AdBlue
® in your
vehicle.
F
W
ithout pressing, turn the black cap a
q
uarter turn anti-clockwise and lift it off.
F
T
urn the blue cap a 6
th of a turn anti-
clockwise.
F
L
ift
off
the
cap.
F
O
btain a bottle of AdBlue
®. After first c
hecking
the
use-by
date,
read carefully
t
he instructions on use on the label before
pouring
the
contents
of
the bottle into your
v
ehicle's
Ad
Blue
® tank.
7
Practical information
Page 303 of 527

301
C4-Picasso-II_en_Chap08_en-cas-panne_ed01-2016
Changing a bulb
For H7 type bulbs with lugs... take care to observe their correct installation
so
as to ensure the best lighting
p
erformance.
Risk of electrocution
Xenon bulbs (D5S-25W) must be
replaced by a CITROËN dealer or a
qualified
w
orkshop.
Front lamps
Model with xenon headlamps
1. Directional dipped beam headlamps (D5S-25W).
2.
M
ain beam headlamps (H7-55W).
3.
D
aytime running lamps / sidelamps
(
6 light emitting diodes - LEDs).
4.
D
irection indicators
(
6 light emittng diodes - LEDs).
5.
F
ront foglamps (H11-55W).
Model with halogen headlamps
1. Dipped beam headlamps (H7-55W).
2. M ain beam headlamps (H7-55W).
3.
D
aytime
r
unning
lam
ps/sidelamps
(
4 light emitting diodes - LEDs).
4.
D
irection indicators (PW Y24W).
5.
F
oglamps
(
H11-55W). In
some weather conditions (e.g. low
t
emperature or humidity), the presence
of misting on the internal sur face of the
g
lass of the headlamps and rear lamps
i
s normal; it disappears after the lamps
h
ave been on for a few minutes.
Light- emitting diodes - LEDs
For replacement, contact a CITROËN dealer or
qualified w
orkshop.
8
In the event of a breakdown
Page 306 of 527
304
C4-Picasso-II_en_Chap08_en-cas-panne_ed01-2016
The direction indicator bulb is located below
the front lamp.
F
T
urn the bulb holder a quarter turn anti-
clockwise.
F
R
emove the bulb holder.
F
C
hange the failed bulb.
For reassembly, carry out these operations in
reverse
o
rder.
Direction indicators Front foglamps
F Unclip the finisher by pulling at the top.
F R emove the two screws to remove the unit.
F
T
urn the bulb holder a quarter turn.
F
R
emove the bulb holder.
F
C
hange the failed bulb.
For reassembly, carry out these operations in
reverse
order, pressing on the finisher to refit it.
Faster
flashing
of
a
direction
indicator
w
arning
lamp
(left
or
right)
indicates
a
f
ailed
bulb
on
that
side.
Direction indicators (light
emitting diodes - LED)
For the replacement of this type of lamp,
contact a CITROËN dealer or a qualified
workshop.
In the event of a breakdown
Page 307 of 527
305
C4-Picasso-II_en_Chap08_en-cas-panne_ed01-2016
You should contact a CITROËN dealer or a
qualified workshop for the replacement of the
l
ight-emitting diode - LED.
Door mirror spotlamps
Integrated direction indicator
side repeaters
You should contact a CITROËN dealer or a
qualified workshop for the replacement of these
b
ulbs. 1.
D
irection indicators (PY21W amber)
.
2.
S
idelamps / foglamps (P21/5W)
.
Rear lamps
Light-emitting diodes -
LEDs
For replacement, contact a CITROËN
dealer
or qualified workshop.
3.
B
rake
lamps
/
sidelamps
(light-emitting
d
iodes
-
LEDs).
4. R
eversing
lamps
(W16W).
5.
D
irection
indicators
(PY21W).
Model with LED lamps
3. Sidelamps ( 5W5).
4. B rake lamps (P21/ W).
5.
D
irection indicators (W Y16W).
6.
R
eversing lamps (W16W).
Model with conventional bulb lamps
8
In the event of a breakdown
Page 309 of 527
307
C4-Picasso-II_en_Chap08_en-cas-panne_ed01-2016
1. Direction indicators (PY21W amber).
2. S idelamps / foglamps (P21/5W).
Rear lamps
3. Sidelamps (light-emitting diodes - LEDs).
4. B rake lamps (light-emitting diodes - LEDs).
5.
D
irection indicators (PY21W).
6.
R
eversing lamps (light-emitting diodes -
L
ED s).
Model with LED lamps
3. Sidelamps ( W5W).
4. B rake lamps / sidelamps (P21W).
5.
D
irection indicators (W Y16W).
6.
R
eversing lamps (W16W).
Model with conventional bulb lamps
Light-emitting diodes -
LEDs
For replacement, contact a CITROËN
dealer or qualified workshop.
8
In the event of a breakdown
Page 311 of 527
309
C4-Picasso-II_en_Chap08_en-cas-panne_ed01-2016
Direction indicator, sidelamp and
foglamp
Access is by passing a hand under the bumper.
F T urn the bulb holder a quarter of a turn and
pull
it out.
F
C
hange the bulb.
For reassembly carry out these operations in
reverse
o
rder.
You can also contact a CITROËN dealer or a
qualified
workshop for the replacement of these
b
ulbs. For the replacement of this type of lamp,
contact a CITROËN dealer or a qualified
workshop.
Third brake lamp (light emitting
diodes-LED)
Number plate lamps (W5W)
To refit, press on the lens to clip it in place.
F
I
nsert a thin screwdriver into one of the cut-
outs in the lens.
F
P
ush it outwards to unclip it.
F
R
emove the lens.
F
C
hange the faulty bulb.
8
In the event of a breakdown