2016 Citroen C4 PICASSO Socket

267
C4-Picasso-II_en_Chap07_info-pratiques_ed01-2016
The fitting of electrical equipment or accessories which are not
recommended by CITROËN may result
in
  a   failure   of   your   vehicle's   electronic  
s

ystem   and   excessive   electrical  
c

onsumption.
Contact a CITROËN dealer
for
  information   on   the   range   of  
r

ecommended equipment and
accessories.
Installation of radio
communication
transmitters
Before installing any after-market radio c ommunication transmitter, you can
contact a CITROËN dealer for the
specification of transmitters which can
be
  fitted   (frequency,   maximum   power,  
a

erial position, specific installation
requirements), in line with the Vehicle
Electromagnetic
 C

ompatibility
 D

irective (2004/104/EC). Depending
  on   the   legislation   in   force   in  
t

he country, certain safety equipment
may   be   compulsory:   high   visibility  s
afety   vests,   warning   triangles,  b
reathalyzers, spare bulbs, spare fuses,
fire
  extinguisher,   first   aid   kit,   mud   flaps  
a

t   the   rear   of   the   vehicle.
"Multimedia"
Portable satellite navigation system, driving assistance   systems,   reversing   camera,  
p

ortable video screen, portable video carrier,
smartphone carrier, Bluetooth
® hands-free kit, t
wo-screen
 
video
 
pack,
 
portable   video   player,  
C

D
 
player,
 
230
 
V/50
 
Hz
 
socket,   230   V/12   V  
a

daptor,
 
iPhone/iPad
 
charger...
By
 
visiting
 
a
 
CITROËN
 
dealer
 
you   can   also  
o

btain
 
cleaning
 
and
 
maintenance   products  
(

interior
 
and
 
exterior)
 
-
 
including   ecological  
p

roducts
 
in
 
the
 
"TECHNATURE"   range,  
p

roducts
 
for
 
topping-up
 
(screenwash...),   paint  
t

ouch-up
 
pens
 
and
 
aerosols
 
for   the   exact  
c

olour
 
of
 
your
 
vehicle,
 
refills
 
(sealant   cartridge  
f

or
 
the
 
temporary
 
puncture
 
repair   kit...), ...
7
Practical information

285
C4-Picasso-II_en_Chap08_en-cas-panne_ed01-2016
A. "Sealant"  or   "Air"   position   selector.
B. On "I" 
/   off   "O" s witch.
C.
 D

eflation   button.
D.
 P

ressure   gauge   (in   bars   and   psi).
E.
 C

ompartment   housing   a   cable   with   an  
a

daptor   for   a   12   V   socket.
Description of the kit
The speed limit sticker I must be affixed to   the   vehicle's   steering   wheel   to   remind  
y

ou   that   a   wheel   is   in   temporary   use.
Do
  not   exceed   a   speed   of   50   mph  
(

80 km/h)   when   driving   with   a   tyre  
r

epaired   using   this   type   of   kit.
F.
 S

ealant
 c
artridge.
G.
 W

hite   pipe   with   cap   for   repair.
H.
 B

lack   pipe   for   inflation.
I.
 S

peed   limit   sticker.
The
 
tyre
 
inflation
 
pressures
 
are
 
given
 
on
 
this
 
lab

el.
The
 
vehicle's
 
electric
 
system
 
allows
 
the
 
c

onnection
 
of
 
the
 
compressor
 
for
 
long
 
e

nough
 
to
 
inflate
 
a
 
tyre
 
after
 
a
 
puncture
 
r

epair.
8
In the event of a breakdown

286
C4-Picasso-II_en_Chap08_en-cas-panne_ed01-2016
1. Sealing
Repair procedure
Avoid removing any foreign bodies which   have   penetrated   into   the   tyre.F

U
ncoil the white pipe G  
f
ully.
F  
U
nscrew   the   cap   from   the   white   pipe.
F
C
onnect the white pipe to the valve of the
tyre   to   be   repaired.
F
 
S

witch   off   the   ignition.
F

T

urn the selector A to the "sealant"
position.
F
 
C

heck   that   the   switch   B is in
position "O" . F  
C
onnect   the   compressor's   electric   plug   to  
t

he   vehicle's   12   V   socket.
F  
S
tart   the   vehicle   and   leave   the   engine  
r

unning.Take care, this product is harmful if s
wallowed   and   causes   irritation   to   the   eyes.
Keep this product out of the reach of
children.Do not start the compressor before
connecting   the   white   pipe   to   the   tyre  
v

alve:   the   sealant   product   would   be  
e

xpelled   through   the   pipe.
In the event of a breakdown

288
C4-Picasso-II_en_Chap08_en-cas-panne_ed01-2016
2. Inflation
F Turn the selector A to the "Air" position.
F
 
U
ncoil   the   black   pipe   H  
f
ully.
F
 
C
onnect   the   black   pipe   to   the  
v

alve   of   the   wheel. F
 
C
onnect   the   compressor's   electric   plug   to  t
he   vehicle's   12   V   socket.
F  S tart   the   vehicle   again   and   leave   the  
e

ngine
 r
unning.
As
  soon   as   possible,   go   to   a   CITROËN  
d

ealer   or   a   qualified   workshop.
You must inform the technician that you
have
  used   this   kit.   After   inspection,   the  
t

echnician will advise you on whether
the tyre can be repaired or if it must be
replaced. F
 
A
djust   the   pressure   using   the   compressor  (
to   inflate:   switch   B in position "I"
;  t
o deflate:   switch   B in position "O" and
press button C ), in accordance with the
vehicle's
 
t
yre   pressure   label   (located   on   the  
l

eft   hand   door   aperture).  

A l

oss of pressure indicates that the
puncture
  has   not   been   fully   plugged;  
c

ontact a CITROËN dealer or qualified
workshop
  for   assistance.
F
 
R
emove   and   stow   the   kit.
F
 
D
rive   at   reduced   speed   (50   mph   [80   km/h]  
m

ax)   limiting   the   distance   travelled   to  
a

pproximately   120   miles   (200   km).
In the event of a breakdown

290
C4-Picasso-II_en_Chap08_en-cas-panne_ed01-2016
Checking /adjusting tyre pressures
You can also use the compressor without
injecting  any   product,   to   check   and   if   necessary  
a

djust   your   tyre   pressures.
F

T
urn the selector A to the "Air"
position.
F
 
U
ncoil   the   black   pipe   H  
f
ully.
F
 
C
onnect   the   black   pipe   to   the  
t

yre   valve. F
 C onnect   the   compressor's   electrical  
c

onnector   to   the   vehicle's   12   V   socket.
F
 
S
tart   the   vehicle   and   let   the   engine   run.
F
 
A
djust   the   pressure   using   the   compressor  
(

to   inflate:   switch   B in position "I";
 
t

o deflate:   switch   B in position "O" and
press button C ),
  according   to   the   vehicle's  
t

yre   pressure   label.
F
 
R
emove   the   kit   then   stow   it.Should the pressure of one or more
tyres
  be   adjusted,   it   is   necessary   to  
r

einitialise the under-inflation detection
system.
For more information on Under-
inflation detection , refer to the
corresponding
 s

ection.
In the event of a breakdown

297
C4-Picasso-II_en_Chap08_en-cas-panne_ed01-2016
Removing a wheel
Parking the vehicle
Immobilise the vehicle where it does not
block  traffic:   the   ground   must   be   level,  
s

table   and   not   slippery.
Apply
  the   parking   brake   unless   it   has  
b

een   programmed   to   automatic   mode,  
s

witch   off   the   ignition   and   engage   first  
g

ear*   to   block   the   wheels.
Check
  that   the   braking   warning   lamp  
a

nd the P   warning   lamp   in   the   parking  
b

rake   control   lever   come   on.
For
  greater   safety,   place   the   chock   2
against
  the   wheel   opposite   to   the   one  
b

eing
 c
hanged.
The
  occupants   must   get   out   of   the  
v

ehicle   and   wait   where   they   are   safe.
Never
  go   underneath   a   vehicle  
s

upported   by   a   jack;   use   an   axle   stand.
List of operations
F Remove  the   wheel   bolt   cover(s)   using   the  t
ool 4   (depending   on   equipment).
F
 
F
it   the   security   socket   5 on the
wheelbrace


1   to   slacken   the   security   bolt  
(

if fitted).
F
 
S
lacken   the   other   bolts   (no   more   than   a  
1

/4 turn)   using   the   wheelbrace   1  
o
n l y.
* Position P
 
for
 
an
 
automatic
 
gearbox. Do
  not   use:
-
 
t
he   jack   for   any   purpose   other   than  
l

ifting   the   vehicle,
-
 
a
ny   other   jack   than   the   one  
s

upplied   by   the   manufacturer.F
 
P
lace   the   foot   of   the   jack   3   on   the   ground  
a

nd   check   that   it   is   directly   below   the  
f

ront A or rear B   jacking   point   provided   on  
t

he underbody, whichever is closest to the
wheel   to   be   changed.
Ensure   that   the   jack   is   stable.   If   the  
g

round   is   slippery   or   loose,   the   jack  
m

ay   slip   or   drop   -   Risk   of   injury!
Ensure
  that   the   jack   is   positioned   only  
a

t   one   of   the   jacking   points   A or B
under
  the   vehicle,   making   sure   that   the  
v

ehicle's   contact   sur face   is   centred   on  
t

he   head   of   the   jack.   Other wise   there   is  
a

  risk   of   damage   to   the   vehicle   and/or   of  
t

he   jack   dropping   -   Risk   of   injury!
8
In the event of a breakdown

299
C4-Picasso-II_en_Chap08_en-cas-panne_ed01-2016
Fitting a wheel
F Lower  the   vehicle   fully.
F  F old   the   jack   3   and   detach   it.
List of operations
F Put  the   wheel   in   place   on   the   hub.
F  S crew   in   the   bolts   fully   by   hand.
F
 
P
re-tighten   the   security   bolt   using   the  
w

heelbrace 1 fitted with the security
socket  5
  (depending   on   equipment).
F
 
P
re-tighten   the   other   bolts   using   the  
w

heelbrace 1  
o
n l y.
The
 
jack
 
must
 
only
 
be
 
used
 
to
 
change
 
a
 w
heel
 
with
 
a
 
damaged
 
tyre.
The
 
jack
 
does
 
not
 
require
 
any
 
m

aintenance.
The
 
jack
 
conforms
 
to
 
European
 
l

egislation,
 
such
 
as
 
defined
 
in
 
the
 
M

achinery
 
Directive
 
2006/42/CE.
8
In the event of a breakdown

300
C4-Picasso-II_en_Chap08_en-cas-panne_ed01-2016
Fitting the "space-saver"
spare wheel
If your vehicle is fitted with alloy wheels,
when  tightening   the   bolts   on   fitting,   it  
i

s normal to notice that the washers
do not come into contact with the
"space-saver"
  spare   wheel.   The   wheel  
i

s secured by the conical sur face of
each
  bolt.
After changing a wheel
To correctly store the punctured wheel
in the boot ( not in the location for the
space-saver wheel ), first remove the
central
  cover.
When
  using   the   "space-saver"   type  
s

pare   wheel,   do   not   exceed   50   mph  
(

80 km/h).
Have
  the   tightening   of   the   bolts   and   the  
p

ressure   of   the   spare   wheel   checked  
b

y a CITROËN dealer or a qualified
workshop
  without   delay.
Have the punctured wheel repaired
and refitted to the vehicle as soon as
possible.
F
 
T

ighten
 
the
 
security
 
bolt
 
using
 
the
 w
heelbrace 1 fitted with the security
socket  5
 
(depending
 
on
 
equipment).
F
 
T

ighten
 
the
 
other
 
bolts
 
using
 
the
 
w

heelbrace 1
 
o

n l y.
F
 
R

efit
 
the
 
wheel
 
bolt
 
cover(s)
 
(depending
 
on
 
e

quipment).
F
 
S

tow
 
the
 
tools
 
in
 
the
 
box. The
  tyre   inflation   pressures   are   given   on   this  lab
el.
In the event of a breakdown