2016 Citroen C4 PICASSO lamp

197
C4-Picasso-II_en_Chap04_conduite_ed01-2016
F Once you have identified a parking   zone,   press   this   button.
Assistance with bay parking
manoeuvres
This indicator lamp comes on in the
instrument panel to confirm activation
of
  the   function. F

O
perate the direction indicator on the
parking   side   chosen   to   activate   the  
m

easurement   function.   You   should   drive  a
t   a   distance   of   between   0.5   m   and   1.5   m  f
rom   the   row   of   parked   vehicles.
F
 
D
rive   slowly   following   the   instructions   until  
t

he   system   finds   a   free   space.F
 
M
ove   for wards   slowly   until   a   message   is  
d

isplayed, accompanied by an audible
signal,
  asking   you   to   engage   reverse   gear.
F

L
imit the speed of the vehicle to
a
  maximum   of   12   mph   (20   km/h)  
a

nd select " Enter bay parking
space " on the touch screen
tablet. When several successive bays are
found, the vehicle will be directed
towards
  the   last   one.
4
Driving

198
C4-Picasso-II_en_Chap04_conduite_ed01-2016
F Select  reverse,   release   the   steering   wheel  a
nd   start   moving   without   exceeding   4   mph  
(

7   km/h).
F
 
T
he   assisted   parking   manoeuvre   is   in  
p

rogress.
 W

ithout   exceeding   4   mph   (7   km/h),   follow  
t

he instructions displayed in the instrument
panel,
  aided   by   the   warnings   from   the  
"

Parking   sensors"   system,   until   the  
i

ndication   of   the   end   of   the   manoeuvre.At
  the   end   of   the   manoeuvre,   the   operating  i
ndicator   lamp   goes   off   in   the   instrument   panel,  
a

ccompanied   by   a   message   and   an   audible  
s

ignal.
The
  assistance   is   deactivated:   you   can   take  
ov

er   control.During
  parking   and   exit   from  p
arking   manoeuvres,   the   reversing  
c

amera function may come into
operation.
  It   facilitates   monitoring   of  
t

he   surroundings   of   the   vehicle,   by  
d

isplaying   additional   information   in   the  
in

strument
 pan
el.
For more information on the Reversing
camera ,
  refer   to   the   corresponding  
s

ection.
During
  a   bay   parking   manoeuvre,   the  
P

ark   Assist   system   is   automatically  
d

eactivated once the rear of the vehicle
is   within   50   cm   of   an   obstacle.
Driving

199
C4-Picasso-II_en_Chap04_conduite_ed01-2016
The system is deactivated by pressing the control.
The
  system   is   deactivated   automatically:
-
 
o
n   switching   off   the   ignition,
-
 
i
f   the   engine   stalls,
-

i
f no manoeuvre is started within 5 minutes
of selection of the type of manoeuvre,
-
 
a
fter   a   prolonged   stop   of   the   vehicle   during  
a

manoeuvre,
-
 
i
f   the   road   wheel   anti-slip   regulation   (ASR)  
i

s
 t
riggered,
-
 
i
f   the   speed   of   the   vehicle   exceeds   the  
s

tated limit,
-

w
hen the driver interrupts movement of the
steering
 w

heel,
-

a
fter 4 manoeuvre cycles,
-
 
o
n   opening   the   driver's   door,
-

i
f one of the front wheels encounters an
obstacle.
The
  operation   indicator   lamp   goes   off   in   the  
i

nstrument   panel   and   a   message   is   displayed  
a

ccompanied   by   an   audible   signal.
The
  driver   should   then   take   back   control   of   the  
v

ehicle's
 s
teering.
Deactivation
The system is switched off automatically:
-  w hen   towing   a   trailer,   connected  
e

lectrically,
-
 
i
f   the   driver's   door   is   opened,
-

i
f the speed of the vehicle is above 42 mph
(70
  km/h).
To
  switch   the   system   of   for   a   prolonged   period,  
c

ontact a CITROËN dealer or a qualified
workshop.
Operating faults
In the event of a fault with the power
steering,   this   warning   lamp   flashes   in  
t

he instrument panel, accompanied
by
  a   message.
Contact a CITROËN dealer or a qualified
workshop.
Switching off
If the lateral distance between your
vehicle   and   the   space   is   too   great,   the s

ystem may not be able to measure the
space.
Anything
  projecting   beyond   the   envelope
 o

f the vehicle (a ladder on the roof, for
example)
  is   not   taken   into   account   by   the
 P

ark   Assist   system   during   a   manoeuvre.
In bad weather or in winter, ensure that
the sensors are not covered by road
dirt,
  ice   or   snow.
In the event of a fault, have the system
checked
  by   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop.
If
 
the
 
system
 
is
 
deactivated
 
during
 
a
 
ma

noeuvre, the drive should reactivate
it
 
to
 
repeat
 
the
 
measurement. In
 
the
 
event
 
of
 
a
 
fault,
 
this
 
warning
 
l

amp flashes for a few seconds,
accompanied
 
by
 
an
 
audible
 
signal.
If
 
the
 
fault
 
occurs
 
during
 
the
 
use
 
o

f
 
the
 
system,
 
the
 
warning
 
lamp
 
g

oes off. High pressure jet washing
When
  washing   your   vehicle,   keep   the  
l

ance   at   least   30   cm   away   from   the  
sen

sors.
4
Driving

201
C4-Picasso-II_en_Chap04_conduite_ed01-2016
Under-inflation alertReinitialisation
This is given by fixed illumination of t
his   warning   lamp,   accompanied   by  
a

n   audible   signal   and,   depending   on  
e

quipment,   the   display   of   a   message. It is necessary to reinitialise the system every
time
  one   or   more   tyre   pressures   are   adjusted,  
a

nd   after   changing   one   or   more   wheels.
F

R

educe speed immediately, avoid
excessive
  steering   movements   and   sudden  
b

raking.
F

S

top the vehicle as soon as it is safe
to
 
do
 
so. F
I n the event of a puncture, use the
temporary
  puncture   repair   kit   or   the   spare  
w

heel   (depending   on   equipment),
or
F

i
f you have a compressor, such as the one
in
  the   temporary   puncture   repair   kit,   check  
t

he pressures of the four tyres when cold,
or
F
 
i
f   it   is   not   possible   to   make   this   check  
i

mmediately, drive carefully at reduced
speed.
The loss of pressure detected does not
always
  cause   visible   bulging   of   the   tyre.  
D

o
 
not   satisfy   yourself   with   just   a   visual  
c

heck. The alert is maintained until the system
is
 r

einitialised.
Snow chains
The system does not have to be
reinitialised  after   fitting   or   removing  
sn

ow
 c
hains.
Before
  reinitialising   the   system,   ensure  
t

hat the pressures of the four tyres are
correct for the use of the vehicle and in
line with the recommendations on the
tyre   pressure   label.
The under-inflation alert can only
be relied on if the reinitialisation of
the system has been done with the
pressures in the four tyres correctly
adjusted.
The under-inflation detection system
does   not   give   a   warning   if   a   pressure   is  
i

ncorrect   at   the   time   of   reinitialisation.
4
Driving

202
C4-Picasso-II_en_Chap04_conduite_ed01-2016
Reinitialisation of the system is done in the
touch  screen   tablet,   with   the   ignition   on   and   the  
v

ehicle   stationary.
F

I
n the Driving menu, select the " Driving
assistance " tab then "Under-inflation
initialisation".
F
 
C
onfirm   the   instruction   by   pressing   "Ye s ",
an
  audible   signal   and   a   message   confirm  
th

e
 r
einitialisation.
The
  new   pressure   settings   registered   are  
c

onsidered to be reference values by the
system.
Operating fault
The flashing and then fixed illumination of the u nder-inflation w arning lam p a ccompanied b

y   illumination   of   the   Service   warning   lamp  
i

ndicates   a   fault   with   the   system.
A
  message   appears,   accompanied   by   an  
a

udible
 s
ignal.
Before
  doing   anything   to   the   system,  
t

he pressures of the four tyres must be
checked
  and   the   system   reinitialised.
The under-inflation alert can only be
relied on if reinitialisation of the system
is done with the four tyre pressures
correctly
 
set. In
  this   case,   under-inflation   monitoring   of   the  
t

yres   is   no   longer   assured.
Have
  the   system   checked   by   a   CITROËN  
d

ealer   or   a   qualified   workshop.
Driving

204
C4-Picasso-II_en_Chap05_eclairage-visibilite_ed01-2016
Rear view mirror
Equipped with an anti-dazzle system, which darkens the mirror glass and reduces the nuisance to the   driver   caused   by   the   sun,   headlamps   from   other   vehicles...
Manual model
Adjustment
F A djust   the   mirror   so   that   the   glass   is  
d

irected   correctly   in   the   "day"   position.
In order to ensure optimum visibility
during
  your   manoeuvres,   the   mirror  
l

ightens   automatically   when   reverse  
g

ear
 i
s
 enga
ged.
Day / night position
F
 
P
ull   the   lever   to   change   to   the   "night"   anti-
dazzle
  position.
F
 
P
ush   the   lever   to   change   to   the   normal  
"

day"   position.
Automatic "electrochrome"
model
This system automatically and progressively changes   between   the   day   and   night   uses   by  
m

eans   of   a   sensor,   which   measures   the   light  
f

rom   the   rear   of   the   vehicle.
Automatic tilting in reverse gear
With the engine running, on engaging reverse gear,   the   mirror   glasses   tilt   downwards.
They
  return   to   their   initial   position:
-

a few seconds a fter c oming o ut o f r everse g ear,- once  the   speed   of   the   vehicle   exceeds  6 m
ph   (10   km/h),
-
 
o
n   switching   off   the   engine.
System
  which   provides   a   view   of   the   ground  
d

uring   parking   manoeuvres   in   reverse   gear.
This function can be deactivated in the Driving
menu.
F

Sel
ect the " Setting" tab then " Comfort"
and " Auto mirror dipping in reverse".
Lighting and visibility

206
C4-Picasso-II_en_Chap05_eclairage-visibilite_ed01-2016
Lighting control stalk
Main lighting
The various front and rear lamps of the vehicle
are  designed   to   adapt   the   driver's   visibility  
p

rogressively   according   to   the   climatic  
c

onditions:
-

s
idelamps, to be seen,
-
 
d
aytime   running   lamps   to   be   more   visible  
d

uring   the   day,
-

d
ipped beam headlamps to see without
dazzling
 o

ther
 d
rivers,
-

m
ain beam headlamps to see clearly when
the
  road   is   clear.
Additional lighting
Other lamps are provided to meet the
requirements  of   particular   driving   conditions:
-
 r

ear
 fo
glamps,
-
 
f
ront   foglamps   with   cornering   lighting,
-
d

irectional headlamps for improved
visibility
 w

hen
 c
ornering,
-
 
g
uide-me-home   and   welcome   lighting   to  
f

acilitate access to the vehicle,
-
 
p
arking   lamps   as   vehicle   position   markers.
Programming
The setting of some functions can be adjusted:
- a utomatic illumination of headlamps,
-
 
a
utomatic   headlamp   dipping,
-
 
g
uide-me-home   lighting,
-
 
w
elcome   lighting,
-
 
c
ornering   lighting,
-
 d

irectional
 l
ighting.
In
 
some
 
weather
 
conditions
 
(e.g.
 
low
 
t

emperature or humidity), the presence
of
 
misting
 
on
 
the
 
internal
 
sur face
 
of
 
the
 
g

lass
 
of
 
the
 
headlamps
 
and
 
rear
 
lamps
 
i

s
 
normal;
 
it
 
disappears
 
after
 
the
 
lamps
 
h

ave
 
been
 
on
 
for
 
a
 
few
 
minutes.
Travelling abroad
Halogen headlamps
For   motoring   in   countries   that   drive  
o

n the other side of the road, it is
necessary
  to   adapt   the   adjustment   of  
t

he dipped beams so as to not dazzle
the
  drivers   of   approaching   vehicles.  
C

ontact a CITROËN dealer or qualified
workshop.
Xenon headlamps
The
  design   of   the   dipped   beam  
h

eadlamps allows you to drive in a
country that drives on the other side
of the road, without the need for any
modification.
In the event of the failure of one or more
bulbs,
 
a
 
message
 
advises
 
you
 
to
 
check
 
t

he
 
lamp(s)
 
in
 
question.
Selection
 
and
 
control
 
of
 
the
 
various
 
front
 
and
 
rear
 
lamps
 
providing
 
the
 
vehicle's
 
lighting.
Lighting and visibility

207
C4-Picasso-II_en_Chap05_eclairage-visibilite_ed01-2016
Displays
Illumination of the corresponding indicator lamp in the instrument panel confirms that the
lighting
  selected   is   on.
The rear sidelamps and direction
indicators
  are   located   on   the   tailgate.  
W

hen   they   are   on,   opening   the   tailgate  
a

utomatically transfers illumination to
the lamps located in the rear bumper, to
maintain
  the   safety   of   the   vehicle.
Main lighting
Lighting off (ignition off) /Daytime running lamps (engine running).
Automatic illumination of headlamps.
D aytime   running   lamps   /   Dipped  
b

eam   /   Main   beam.
Sidelamps.
Dipped
  or   main   beam   headlamps.
Turn
 
the
 
ring   A to place the desired symbol
against
 
the   mark.
Selection of main lighting mode
Model without AUTO lighting
Model with AUTO lighting Headlamp dipping
Pull the stalk B towards you to switch the
l ighting   between   dipped   and   main   beam  
h

eadlamps or to activate automatic headlamp
dipping.
In
  the   lighting   off   and   sidelamps   modes,   the  
d

river can switch on the main beam headlamps
temporarily
  ("headlamp   flash")   by   maintaining   a  
p

ull   on   the   stalk.
5
Lighting and visibility