2016 Citroen BERLINGO MULTISPACE RHD bonnet

DIESEL
162
Berlingo-2-VP_en_Chap07_Verification_ed02-2015
Fuel
Berlingo-2-VP_en_Chap07_Verification_ed02-2015
FUEL CUT- OFF
In a serious collision, a mechanism automatically
  prevents   fuel   from  
reaching

  the   engine.
The
  flashing   of   this   warning  
lamp

  is   accompanied   by   a  
message

  in   the   screen.
Check
  that   there   is   no   odour   or  
leakage

  of   fuel   outside   the   vehicle   and  
re-establish

  the   fuel   supply:
-

switch of
f the ignition
(ST
o

P

position),
-
 
remove
  the   key,
-
 
put
  the   key   back   in   the   ignition,
-
 
switch
  on   the   ignition   and   start.
DIESEL PRIMING PUMPFuel used for Diesel engines
The Diesel engines  are  compatible  with  biofuels
  which   conform   to   current   and  
future European standards (

d iesel fuel
which
  complies   with   standard   EN   590  
mixed

  with   a   biofuel   which   complies  
with standard E

n 14214) available at
the
  pumps   (containing   up   to   7   %   Fatty  
Acid

  Methyl   Ester).
B30 biofuel can be used in certain
Diesel
  engines.   However,   this   use,  
even occasional, requires strict
application of the special servicing
conditions.

  Contact   a   CITROËN   dealer  
or

  a   qualified   workshop.
The use of any other type of (bio)fuel
(vegetable  or   animal   oils,   pure   or   diluted, domestic

  fuel...)   is   strictly   prohibited
 (risk

  of   damage   to   the   engine   and   fuel
 system).
If you run out of fuel, it is necessary to
prime  the   fuel   circuit.
Other HDi engines
- Fill  the   fuel   tank   with   at   least   five  litres
  of   Diesel.
-
 
Squeeze
  and   release   the   manual  
priming

  pump,   under   the   bonnet,  
under

  the   protective   cover.
-
o perate the starter until the engine
starts.
BlueHDi engine
- Fill   the   fuel   tank   with   at   least   five  litres
  of   Diesel.
-

Switch on the ignition (without
starting

  the   engine).
-
 
W
ait   around   6   seconds   and   switch  
of

f   the   ignition.
-
 
Repeat
  the   operation   10   times.
-
o perate the starter to run the
engine.

181
Berlingo-2-VP_en_Chap08_aide-rapide_ed02-2015Berlingo-2-VP_en_Chap08_aide-rapide_ed02-2015
2. Sidelamps
T ype A, W5W - 5W
-
 
Remove
  the   cover   by   pulling   the  
flexible

  rubber   tab.
-
 
Remove
  the   bulb   holder   fitted   by  
pressure

  by   pulling   the   connector.
-
 
Change
  the   bulb.
-
 
Ensure
  that   the   cover   is   refitted  
correctly all round to assure correct
sealing.
Front lamps
1. Dipped / Main beam headlamps
T ype C, H4 - 55W
-
 
Remove
  the   centre   cover   by   pulling  
the

  flexible   rubber   tab.
-
 
Disconnect
  the   electrical   connector.
-
 
Release
  the   retaining   tab.
-
 
Change
  the   bulb   taking   care  
to

  align   the   metal   part   with   the  
grooves

  on   the   lamp.
-
 
Reposition
  the   retaining   tab.
-
 
Ensure
  that   the   cover   is   refitted  
correctly all round to assure correct
sealing.
High pressure washing Open

 
the
 
bonnet.
 
T

o
 
access
 
the
 
bulbs,
 
reach

 
behind
 
the
 
headlamp
 
unit.
Carry out the operations in reverse
order
 
to
 
refit
 
each
 
bulb
 
and
 
check
 
that
 
the

 
bonnet
 
is
 
closed
 
securely.
Halogen
 
bulbs
 
must
 
be
 
changed
 
with

 
the
 
headlamp
 
off.
 
Wait
 
a
 
few minutes

 
(risk
 
of
 
serious
 
burns).

 
Do
 
not
 
touch
 
the
 
bulb
 
directly
 
with

 
your
 
fingers,
 
use
 
a
 
lint-free
 
cloth.
It
 
is
 
normal
 
for
 
condensation
 
to
 
form
 
inside

 
the
 
headlamps.
 
Regular
 
use
 
of
 the
 
vehicle
 
eliminates
 
this
 
misting.
The
 
bulbs
 
must
 
be
 
changed
 
with
 
the ignition of

f or with the battery
disconnected.
 
Wait
 
approximately
 

3
 
minutes
 
after
 
changing
 
the
 
bulb
 
before

 
reconnecting
 
the
 
battery.
Check
 
that
 
the
 
lamps
 
operate
 
correctly
 
after

 
each
 
operation.
When using this type of washing
on stubborn dirt, do not persist on
the
 
headlamps,
 
the
 
lamps
 
and
 
their
 
edges

 
to
 
avoid
 
damaging
 
their
 
coating
 
and

 
seals.
QUICk HELP
8
Changing a bulb

186
Berlingo-2-VP_en_Chap08_aide-rapide_ed02-2015Berlingo-2-VP_en_Chap08_aide-rapide_ed02-2015
CHANGING A FUSE
The fuseboxes are located:
-
in the lower dashboard on the

left-hand side (behind the cover),
-
 
under
  the   bonnet   (near   the   battery).
The
  information   given   concerns   only  
those fuses which can be changed by
the user using the tweezer

, located
behind the dashboard storage
compartment
  on   the   right-hand   side.  
For

  any   other   work,   visit   a   CITROËN  
dealer

  or   a   qualified   workshop.
Removing and fitting a fuse
Always replace a failed fuse with a
fuse of the same rating.
Motor
 
trade
 
technicians:
 
for
 
complete

 
information
 
on
 
the
 
fuses
 
and relays, refer to the "Repair
Manual"

 
diagrams
 
via
 
the
 
dealer
 
network.
CITR

o
Ë
n
will not accept responsibility
for the cost incurred in repairing
your vehicle or for rectifying the
malfunctions
 
resulting
 
from
 
the
 installation of accessories not
supplied
 
and
 
not
 
recommended
 
by
 
the
 
CITROËN

 
network
 
and
 
not
 
installed
 
in accordance with its instructions,
in

 
particular
 
when
 
the
 
combined
 
consumption

 
of
 
all
 
of
 
the
 
additional
 
equipment

 
connected
 
exceeds
 

10
 
milliamperes. Before replacing a fuse, the cause of
the
  incident   must   be   identified   and  
rectified.
●

 
Use
  the   tweezer.
Changing a fuse

189
Berlingo-2-VP_en_Chap08_aide-rapide_ed02-2015Berlingo-2-VP_en_Chap08_aide-rapide_ed02-2015
Fuses under the bonnet
after opening the bonnet, unclip and tilt
the corresponding box to gain access
to
  the   fuses. Fuses
F Amperes  
a a llocation
1 20 Engine
  management
2 15 Horn
3 10 Front
  and   rear   wash-wipe   pump
4 20 Headlamp
  wash   pump
5 15 Engine
  components
6 10 Steering wheel angle sensor,
d SC
7 10Brake
  switch,   clutch   switch
8 25 Starter
  motor
9 10Headlamp
  beam   motor,   fleet   management   unit
10 30 Engine
  components
11 40
n

ot used
12 30 Wipers
13 40 Built-in
  systems   interface
14 30 Pump
15 10 Right-hand
  main   beam   headlamp
16 10Left-hand
  main   beam   headlamp
17 15Right-hand
  dipped   beam   headlamp
18 15 Left-hand
  dipped   beam   headlamp
QUICk HELP
8
Changing a fuse