2016 Citroen BERLINGO MULTISPACE steering

63
Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2016
TRIP COMPUTER
A

few definitions
Range: displays the distance which
can  travelled   with   the   remaining   fuel  
detected

  in   the   tank,   basd   on   the  
average

  consumption   over   the   last   few  
miles

  (kilometres).
This
  displayed   value   may   vary  
significantly

  following   a   change   in   the  
vehicle

  speed   or   the   relief   of   the   route.Current fuel consumption:
only
calculated and displayed above
20   mph   (30   km/h).
Average fuel consumption: this is the
average   fuel   consumption   since   the  
last

  trip   computer   zero   reset.
Distance travelled: calculated since
the   last   trip   computer   zero   reset.
Distance remaining to the
destination: calculated with reference to
the   final   destination,   entered   by   the   user.
 If guidance is activated, the navigation


system   calculates   it   as   a   current   value.
Average speed: this is the average
speed calculated since the last trip
computer
  zero   reset   (ignition   on).
Each press of the button, located at
the
 
end
 
of
 
the
 
wiper
 
stalk,
 
displays
 
the
 
dif

ferent
 
trip
 
computer
 
information
 
in
 
turn,

 
depending
 
on
 
the
 
screen.
When the required trip is displayed,
press  the   control   for   more   than  
two seconds. When
  the   range   falls   below   20   miles  
(30

  km),   dashes   are   displayed.  
After
 
fillin

g   with   at   least   10   litres   of   fuel,   the  
range is recalculated and is displayed
when

  it   exceeds   60   miles   (100   km).
If, whilst driving, dashes are displayed
continuously in place of the digits,
contact   a   CITROËN   dealer.
The "vehicle" tab with the range,
current
 
fuel
 
consumption
 
and
 
the
 remaining
 
distance
 
to
 
run.
The "1" tab (trip 1) with the average
speed,
 
the
 
average
 
fuel
 
consumption
 
and the distance travelled in trip

"1".
The
 
"2"
 
tab
 
(trip
 
2)
 
with
 
the
 
same
 
information

 
for
 
a
 
2
nd trip.
Reset
Steering mounted controls
EaSE oF USE and CoMFoRT
4

64
Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2016
CRUISE CONTROL
"CRUISE"
"This is the speed at which the driver
wishes  to   drive".
This
  aid   to   driving   in   free-flowing  
traffic

  enables   the   vehicle   to   maintain  
the

  speed   programmed   by   the   driver,  
unless

  a   steep   gradient   makes   this  
impossible.
For

  the   system   to   be   programmed   or  
activated,

  the   vehicle   speed   must   be  
greater

  than   25   mph   (40   km/h)   with  
4th gear

  or   higher   engaged. The
  state   of   the   cruise   control   system  
can

  be   seen   in   the   instrument   panel  
together

  with   the   the   programmed  
speed

  setting.
Function selected,
display of the "Cruise
Control"   symbol.
Function off,
OFF
Function   on.
Vehicle speed above,
the   programmed  
speed

  flashes.
o

perating fault
detected,
OFF - the dashes
flash.
1.
 Cruise
 
control
 
mode
 
On
 
/
 
Off.
2.
 
Reduce

 
cruise
 
speed
 
setting.
3.
 
Increase

 
cruise
 
speed
 
setting.
4.
 
Pause

 
/
 
Resume
 
cruise
 
control.
Steering mounted controls

65
Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2016
Selecting the functionFirst activation /
Programming a
speed Temporarily exceeding the
speed setting
Deactivation (off)
- Press this button or
the  brake   or   clutch  
pedal.
Reactivation
- Following deactivation of the cruise
control,  press   this   button.
Your vehicle will return to the last
programmed
  speed.
Alternatively,
  you   can   repeat   the   "first  
activation"

  procedure.
It is possible to accelerate and drive
momentarily
 
at
 
a
 
speed
 
greater
 
than
 
the

 
programmed
 
speed
 
setting.
 
The

 
value

 
programmed
 
flashes.
When the accelerator pedal is
released, the vehicle will return to the
programmed
 
speed.
-

Reach the chosen speed by
pressing

 
the
 
accelerator.
-

Press the

SET - or SET +
 
button.
This
 
programmes/activates
 
the
 
speed
 
setting

 
and
 
the
 
vehicle
 
will
 
maintain
 
this

 
speed.
-

Place the switch in the

CRUISE
position.
 
The

 
cruise
 
control
 
is
 
selected but is not yet active and
no

 
speed
 
has
 
been
 
programmed.
Steering mounted controls
EaSE oF USE and CoMFoRT
4

66
Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2016
Changing the
programmed speedSwitching the system off
Operating fault Cancelling the programmed
speed setting
When the vehicle becomes stationary, after switching of
f the ignition, the
system
  no   longer   memorises   a   speed.
There
 
are
 
two
 
methods
 
of
 
memorising
 
a speed

higher
 
than
 
the
 
previous
 
one:
-
Place the dial in position
0 or switch
off the ignition to switch everything
off.
Good practice
Without using the accelerator
-

Press the
SET +   button.
A brief   press   increases   the   speed   by   1   mph   (km/h).
A maintained   press   increases   the   speed   in steps
  of   5   mph   (km/h).
Using the accelerator
-
 
Exceed
  the   memorised   speed   until  
the speed required is reached,
-


Press the
SET + or SET -   button.
To
  memorise   a   speed   lower than the
previous
  one:
-

Press the
SET -   button.
a brief press decreases the speed by


1
  mph   (km/h).
A
 

maintained   press   decreases   the  
speed

  in   steps   of   5   mph   (km/h).The
  programmed   speed   setting   is  
cleared

  and   replaced   by   three   dashes.  
Contact a CITR

o Ë n dealer or a
qualified
  workshop   to   have   the   system  
checked.When

  changing   the   programmed  
speed

  setting   by   means   of   a  
maintained

  press,   pay   attention   as  
the speed can increase or decrease
rapidly

.
d

o not use the cruise control on
slippery   roads   or   in   heavy   traffic.
In the event of a steep slope, the cruise
control   cannot   prevent   the   vehicle   from  
exceeding

  the   programmed   speed  
setting.
In any event, the cruise control cannot
replace the need to observe the speed
limits

  and   the   need   for   vigilance   on   the  
part

  of   the   driver.
It   is   advisable   to   keep   your   feet   near  
the

  pedals.
To   avoid   any   jamming   under   the  
pedals:
-

 
ensure
  that   the   mat   and   its   fixings  
on

  the   floor   are   positioned   correctly,
-  
never
  place   one   mat   on   top   of  another
.
Steering mounted controls

 67
Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2016
The speed of the vehicle responds to
the pressure of the driver's foot, up
to the the accelerator pedal's point of
resistance, which indicates that the
programmed  speed   has   been   reached.
However, pressing the pedal beyond
this
  point   of   resistance   to   the   floor  
allows

  the   programmed   speed   to   be  
exceeded.

 
T
o   resume   use   of   the   limiter,  
simply

  reduce   the   pressure   on   the  
accelerator pedal gradually and return
to

  a   speed   below   that   programmed.
Adjustments can be carried out
when stationary, with the engine
running, or with the vehicle moving. This
  speed   limiter   shows   the   function  
selection

  status   in   the   instrument   panel  
and

  displays   the   programmed   speed:SPEED LIMITER
"LIMIT"
Function selected,
displaying of the
"Speed
  Limiter"  
symbol.
Function of

f,
last
  programmed  
speed -

OFF.
Function
  on.
Vehicle speed above,
the
  programmed  
speed setting is
displayed

  flashing.
o

perating fault
detected,
OFF - the dashes
flash.
1.
 
Limiter

 
mode
 
On
 
/
 
Off.
2.
 
Reduce

 
programmed
 
speed
 
setting.
3.

 
Increase

 
programmed
 
speed
 
setting.
4.

 
Speed

 
limiter
 
On
 
/
 
Pause.
"This is the selected speed which the
driver
 
does
 
not
 
wish
 
to
 
exceed".
This
 
selection
 
is
 
made
 
with
 
the
 
engine
 running while stationary or with the vehicle


moving.
 
The

 
minimum
 
speed
 
which
 
can
 be

 
programmed
 
is
 
20
 
mph
 
(30
 
km/h).
Steering mounted controls
EaSE oF USE and CoMFoRT
4

68
Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2016
Selecting the functionProgramming a speed setting On / Off
- Place the switch in the LIMIT
position.  The   limiter   is   selected  
but

  is   not   yet   active.  
The
  screen  
indicates

  the   last   programmed  
speed

  setting.
A
 

speed   can   be   programmed   without  
activating

  the   limiter   but   with   the  
engine

  running.
To
  memorise   a   speed   higher than the
previous
  one:
-

Press the
SET +   button.
A brief   press   increases   the   speed   by   1 mph   (km/h).
A
 
maintained   press   increases   the   speed   in   steps   of
 5

  mph   (km/h).
To memorise a speed lower than the
previous   one.
-

Press the
SET -   button.
A brief   press   decreases   the   speed   by   1   mph   (km/h).
A
 
maintained   press   decreases   the   speed   in   steps   of
 5

  mph   (km/h).
Pressing this button once activates
the  limiter,   pressing   the   button   again  
deactivates it

(OFF).
Steering mounted controls

 69
Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2016
Exceeding the programmed
speedSwitching the function offOperating fault
The programmed speed is cleared then
  replaced   by   three   dashes.
Contact a CITR
o Ë n dealer or a
qualified
  workshop   to   have   the   system  
checked.
Flashing of the speed setting
Good practice
In  any   event,   the   speed   limiter   cannot  
replace the need to observe speed
limits,

  nor   can   it   replace   the   need   for  
vigilance

  on   the   part   of   the   driver.
Always
  pay   attention   to   the   profile  
of the road and sharp acceleration
and

  stay   in   complete   control   of   your  
vehicle.
T

o   avoid   any   jamming   under   the  
pedals:
-

 
ensure
  that   the   mat   and   its   fixings  
on

  the   floor   are   positioned   correctly,
-
 
never
  place   one   mat   on   top   of  
another

.
Pressing the accelerator pedal in order
to
 
exceed
 
the
 
programmed
 
speed
 
will have no ef

fect unless you press
the pedal firmly beyond the point of
resistance.
The
 
limiter
 
is
 
deactivated
 
temporarily
 
and

 
the
 
programmed
 
speed
 
flashes
 accompanied
 
by
 
an
 
audible
 
signal.
To
 
return
 
to
 
the
 
limiter
 
function,
 
reduce
 
your

 
speed
 
to
 
below
 
the
 
programmed
 
speed.
The

 
speed
 
setting
 
flashes:
-

following forcing of the accelerator
point of resistance,
-

 
when

 
the
 
limiter
 
cannot
 
prevent
 
an
 
increase in the vehicle speed due
to

 
the
 
profile
 
of
 
the
 
road
 
or
 
on
 
a
 
steep descent,
-

 
in

 
the
 
event
 
of
 
sharp
 
acceleration. -

Place the switch in position

0 or
switch off the ignition to switch the
system
 
off.
The
 
last
 
programmed
 
speed
 
remains
 
in
 
the

 
memory.
Steering mounted controls
EASE OF USE and COMFORT
4

94
Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2016
FRONT FITTINGS
1. Lower glove box
This may or may not be fitted with a lid.
Upper storage compartment
This is located on the dashboard,
behind  the   steering   wheel.
A
 

recess   makes   lifting   of   the   lid   easier  
when

  opening.   Guide   it   to   its   rest  
position.
T

o close, guide the lid then press the
centre
  gently.
Any
  liquid   which   could   spill   risks  
causing an electrical short circuit and
therefore

  a   potential   fire.
3. Side storage compartment
4. Bag hook
Only hang flexible bags which are not too  heavy   on   this   hook.
2. Storage pocket and bottle
holder (1.5 L)
Practical information