2016 Citroen BERLINGO MULTISPACE steering

+
ABS
35
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2016
Instruments and controls
Warning lamp is indicatesSolution - action
Power
steering on. a fault with the
system.The vehicle retains conventional steering without
assistance.
 
Have
 
it
 
checked   by   a   CITROËN  
dealer

 
or
 
a
 
qualified
 
workshop.
Door open
detection on
 
and
 
accompanied
 
by

 
a
 
message
 
in
 
the
 
screen. that a door is not
closed

 
correctly. Check
 
that
 
all
 
of
 
the
 
doors   are   closed.
ABS remaining
 
on. a fault with the anti-
lock
 
braking
 
system. The
 
vehicle
 
retains
 
conventional   braking.
Have
 
it
 
checked
 
by
 
a
 
CITROËN   dealer   or   a  
qualified

 
workshop.
ESC flashing.
triggering of the
a

SR
or
 
DSC
 
regulation. The
 
system
 
optimises   traction   and   improves   the  
directional

 
stability
 
of
 
the   vehicle.
Chapter
 
5,
 
"Driving
 
safety"   section.
remaining
 
on. a fault with the
system.
E.g.:
 
under-inflation
 
of

 
the
 
tyres. E.g.:
 
check
 
the
 
pressure   of   the   tyres.
Have
 
it
 
checked
 
by
 
a
 
CITROËN   dealer   or   a  
qualified

 
workshop.
 
(Wheel   speed   sensor,  
hydraulic

 
valve
 
block,
  ...).
Under-
inflation on.
The tyre pressure is
too
 
low
 
in
 
or
 
more
 
wheels. Check

 
the
 
tyre
 
pressure   as   soon   as   possible.  
This

 
check
 
must
 
be
 
done   with   the   tyres   cold.
flashing
 
then
 remaining

 
on,
 accompanied

 
by
 
the
 Service

warning
lamp,
 
and
 
depending
 on

 
equipment,
 
the
 display

 
of
 
a
 
message. The tyre pressure
monitoring
 
system
 
has a fault or one of
the wheels does not
have

 
a
 
sensor. Detection
 
of
 
under-inflation   is   no   longer   assured.
Have
 
it
 
checked
 
by
 
a
 
CITROËN   dealer   or   a  
qualified

 
workshop.
Particle
filter on. a
 
problem
 
with
 
the
 
particle

 
filter
 
(fuel
 
additive

 
level,
 
risk
 
of
 
blockage, ...). Have

 
the
 
filter
 
checked   by   a   CITROËN   dealer   or  
a

 
qualified
 
workshop.
Chapter
 
7,
 
"Levels"
 
section.
REadY To Go
3

36
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2016
Instruments and controls
Warning lamp is indicatesSolution - action
Dipped beam
headlamps /
Daytime
running
lamps on.a
  manual   selection   or  
automatic

  illumination   of  
headlamps.T

urn   the   ring   on   the   lighting   control   stalk   to   the  
second

  position.
illumination of the  dipped  beam  headlamps from
  the   time   the   ignition   is   switched   on: daytime

  running   lamps   (depending   on   the
 country

  in   which   the   vehicle   is   sold).
Chapter 4, "Steering mounted controls" section.
Main beam
headlamps pullin
g
 
of
 
the
 
stalk
 
towards
 
you. Pull

  the   stalk   to   return   to   dipped   beam  
headlamps.
Direction
indicators flashing

 
with
 
audible

 
signal. a change of direction via
the
 
lighting
 
stalk. To
  the   Right:   control   to   be   pushed   upwards.
To
  the   Left:   control   to   be   pushed   downwards.
Front
foglamps on.
a
 
manual
 
selection. The
  foglamps   only   operate   if   the   sidelamps   or  
dipped

  beam   headlamps   are   on.
Rear
foglamps on.
a
 
manual
 
selection. The
  foglamps   only   operate   if   the   sidelamps   or  
dipped

  beam   headlamps   are   on.
In
  conditions   of   normal   visibility,   switch   them   off  
to

  avoid   breaking   the   law.
"This
  lamp   is   a   dazzling   red".

37
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2016
Instruments and controls
Warning lamp in the
screen is
indicates Solution - action
Cruise
control on.
cruise
 
control
 
selected. Manual
 
selection.
Chapter
 
4,
 
"Steering
 
mounted   controls"   section.
Speed limiter on.speed
 
limiter
 
selected. Manual
 
selection.
Chapter
 
4,
 
"Steering
 
mounted   controls"   section.
Gear shift
indicator on.a
 
recommendation
 
independent of the type and
density

 
of
 
traffic. To
 
reduce
 
fuel
 
consumption,   change   to   an  
appropriate

 
gear
 
with
  a   manual   gearbox.  
The driver retains responsibility to follow this
indication

 
or
 
not.
Diesel pre-
heating on.climatic
 
conditions
 
requiring
 
pre-heating. W

ait
 
until
 
the
 
warning
  lamp   goes   off   before  
operating

 
the
 
starter.
Presence of
water in the
Diesel filter
on and
accompanied by
  a   message   in
 the

  screen.
water in the Diesel filter. Have   the   filter   bled   by   a   CITROËN   dealer   or   a  qualified
  workshop   without   delay.
Chapter   7,   "Checks"   section.
According
  to   country.
Service
spanner on.that a service will be due
shortly. Refer
  to   the   list   of   checks   in   the   maintenance   and  
warranty

  guide.
Have the service carried out by a CITR
o Ë n
dealer
  or   a   qualified   workshop.
Time flashing. adjustment
  of   the   time.Use
  the   left-hand   button   on   the   instrument   panel.
Chapter
  3,   "Instruments   and   controls"   section.
REadY To Go
3

42
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2016
Instruments and controlsThe   alert   is   maintained   until  
the tyre or tyres concerned is
reinflated,

  repaired   or   replaced.
The spare wheel (space-saver type or
a
  steel   rim)   does   not   have   a   sensor.
Operating fault
Under-inflation alert
The loss of pressure detected
does not always lead to visible
deformation
 
of
 
the
 
tyre.
 
Do
 
not
 
rely
 
on

  just   a   visual   check.The alert is given by the fixed illumination  of   this   warning   lamp, accompanied

  by   an   audible   signal,
 and

  depending   on   equipment,   the
 display

  of   a   message.The flashing and then fixed  illumination   of   the  
under-inflation

  warning  
lamp

  accompanied   by   the  
illu

mination   of   the   "Service"   warning  
lamp,

 
and   depending   on   equipment,  
the

 
display   of   a   message   indicates   a  
fault

 
with   the   system.
In
 
this
 
case,   monitoring   of   the   tyre  
pressures

  is   not   assured.
In
 
the
 
event
 
of
 
a
 
problem
 
on
 
one
 
of
 
the

 
tyres,
 
the
 
symbol
 
or
 
the
 
message
 
appears,

 
according
 
to
 
equipment,
 
to
 
identify

 
it.
-

Reduce speed, avoid sudden
steering

 
movements
 
or
 
harsh
 
brake
 
applications.
-

 
Stop

 
as
 
soon
 
as
 
it
 
is
 
safe
 
to
 
do
 
so.
-

In the event of a puncture, use
the

 
temporary
 
puncture
 
repair
 
kit
 
or the spare wheel (according to
equipment),
or
-

 
if

 
you
 
have
 
a
 
compressor,
 
the
 
one
 
in

 
the
 
temporary
 
puncture
 
repair
 
kit

 
for
 
example,
 
check
 
the
 
four
 
tyre
 
pressures when cold,
or
-

 
if

 
it
 
is
 
not
 
possible
 
to
 
check
 
the
 
tyre

 
pressures
 
at
 
the
 
time,
 
drive
 
carefully

 
at
 
reduced
 
speed.
This alert is also displayed when
one
  or   more   wheels   is   not   fitted  
with

  a   sensor   (for   example,   a  
space-saver

  or   steel   spare   wheel).
Go
 
to
 
a   CITROËN   dealer   or   a   qualified  
workshop to

  have   the   system   checked  
or

, following the repair of a puncture, to
have the original wheel, equipped with
a
 
sensor,   refitted.

44
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2016
Instruments and controls
Under-inflation alert
This is given by fixed illumination  of   this   warning   lamp, accompanied

  by   an   audible   signal
 and,

  depending   on   equipment,
 the

  display   of   a   message.
Before
  reinitialising   the   system,  
ensure that the pressures of
the four tyres are correct for the
use of the vehicle and in line with the
recommendations

  on   the   tyre   pressure  
label.
The

  under-inflation   alert   can   only  
be relied on if the reinitialisation of
the

  system   has   been   done   with   the  
pressures in the four tyres correctly
adjusted.
The

  under-inflation   detection   system  
does not give a warning if a pressure is
incorrect

  at   the   time   of   reinitialisation.
The loss of pressure detected
does not always cause visible
bulging
  of   the   tyre.   Do   not   satisfy  
yourself

  with   just   a   visual   check. The
  alert   is   maintained   until   the  
system

  is   reinitialised.
F
 
Reduce
  speed   immediately,   avoid  
excessive

  steering   movements   and  
sudden

  braking
F

Stop the vehicle as soon as it is
safe

  to   do   so. F
In the event of a puncture, use
the
  temporary   puncture   repair   kit  
or the spare wheel (depending on
equipment),
or
F

 
if
  you   have   a   compressor,   such   as  
the

  one   in   the   temporary   puncture  
repair

  kit,   check   the   pressures   of  
the four tyres when cold,
or
F

 
if
  it   is   not   possible   to   make   this  
check

  immediately,   drive   carefully  
at

  reduced   speed.
Reinitialisation
It is necessary to reinitialise the system every  time   one   or   more   tyre   pressures  
are

  adjusted,   and   after   changing   one  
or

  more   wheels.

49
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2016
MANUAL GEARBO x
5-speed
6-speed
To change gear easily, always depress
the
 
clutch
 
pedal   fully.
To
 
prevent
 
the
 
mat   from   becoming  
caught

 
under
 
the   pedal:
-
 
ensure

 
that
  the   mat   is   positioned  
and

 
secured   correctly   on   the   floor,
-
 
never

 
fit
 
one   mat   on   top   of   another.
When driving, avoid leaving your hand
on
 
the
 
gear
 
knob   as   the   force   exerted,  
even

 
if
 
slight,
 
may   wear   the   internal  
components

 
of
  the   gearbox   over   time.
Changing into 5th or 6th gear
To engage the gear correctly, move the gear  lever   fully   to   the   right.
Engaging reverse gear
The lever should be moved slowly to  reduce   noise.
To engage reverse gear, wait until the
vehicle
  has   come   to   a   complete   stop.
STEERING WHEEL ADJUSTMENT
When the vehicle is stationary,
release
  the   steering   wheel   adjustment  
mechanism

  by   pulling   the   lever.
Adjust
  the   steering   wheel   for   height  
and

  reach,   then   lock   the   mechanism   by  
pushing

  the   lever   fully   forward. In
  the   6-speed   configuration,   raise   the  collar
  below   the   gear   knob.
REadY To Go
3
Gearbox and steering wheel

50
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2016
The information appears in  the   instrument   panel  
in

  the   form   of   an   arrow.   It  
may

  be   accompanied   by   a  
recommended

  gear.
The
  system   adapts   its   gear  
change

  recommendation  
according to the driving conditions
(slope,

 
load, ...)   and   the   demands  
of the driver (power

, acceleration,
braking, ...).
The
 
system   never   suggests:
-
 
engaging
  first   gear,
-
 
engaging
  reverse   gear.
With
 
an
 
electronic
 
gearbox,
 
the
 
system
 
is

 
only
 
active
 
in
 
manual
 
mode.
GEAR SHIFT INDICATOR
depending on the driving situation and
your   vehicle's   equipment,   the   system  
may

  advise   you   to   skip   one   (or   more)  
gear(s).

 
Y
ou   can   follow   this   instruction  
without

  engaging   the   intermediate  
gears.
The

  gear   engagement  
recommendations

  must   not   be  
considered

  compulsory.  
This
  is  
because

  the   configuration   of   the   road,  
the

  traffic   density   and   safety   remain  
determining

  factors   when   choosing  
the

  best   gear.  
Therefore,
  the   driver  
remains

  responsible   for   deciding  
whether or not to follow the indications
given.
This

  function   cannot   be   deactivated.
System
 
which
 
reduces
 
fuel
 
consumption

 
by
 
recommending
 
the
 
most

 
appropriate
 
gear.
Gearbox and steering wheel

51
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2016
6-SPEED ELECTRONIC GEARBOx
- automatic  mode:   gear   selector   in  position
A.
-
 
manual
  mode:   gear   selector   in  
position

M.
For
  safety:
It
  is   only   possible   to   come   out  
of position

N   if   the   brake   pedal   is  
pressed.
The

  change   from   position   A (driving in
automatic
  mode)   to   position   M (driving
in
  manual   mode)   or   vice   versa   can   be  
made

  at   any   time.  
The
  warning   lamp   A
goes
  off   in   the   instrument   panel.
Mode selection Moving off
- To start the engine, the gear
selector   must   be   in   position   N.
-
 
Press
  firmly   on   the   brake   pedal.
-
 
Operate
  the   starter.
-

When the engine is running, place
the gear selector on

R, A or M as
desired.
-
 
Release
  the   brake   pedal   and  
accelerate.
If the gear selector is not in position

N,
and/or
  if   the   brake   pedal   is   not  
pressed,

  the   engine   will   not   start.  
Repeat

  the   above   procedure.
Reverse gear Engaging reverse gear
Move the gear selector to R.
Only attempt to select reverse gear
when the vehicle is stationary.
Neutral Changing to neutral
Move the gear selector to N.
  If   the  
vehicle

  is   moving,   do   not   select   this  
position

  even   momentarily.
REadY To Go
3
Gearbox and steering wheel