2016 Citroen BERLINGO MULTISPACE 2016

183
Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2016
Side repeater
Type A, WY5W - 5W (amber)
-
Push the repeater towards the rear
and disengage it by pullin

g the
front.
-

Contact a CITR
o Ë n dealer to
obtain a new repeater which is a
sealed
  component.
-
 
T
o   refit,   engage   the   repeater  
towards the rear and bring it
towards

  the   front.
Courtesy lamps
Type A, 12V5W - 5W
-
Unclip the lens by sliding a
screwdriver in the slots on each
side

  of   the   courtesy   lamp.
-
 
Pull
  the   bulb   out   and   change   it.
-

Clip the lens in its housing and
ensure

  that   it   is   secured   correctly.
Front / Rear
QUICk HELP
8
Changing a bulb

184
Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2016
Rear lamps
This procedure requires the use of
the spanner supplied with the tools for
changing  a   wheel.
When
  refitting,   take   care   to  
reposition the tabs and the wiring
correctly to avoid trapping the
wiring.
a

fter changing the rear direction
indicator
  bulb,   the   reinitialisation   time   is  
above

  2   minutes.
-
Move aside the 4 tabs then extract
the
  bulb   holder.
-
 
Remove
  the   faulty   bulb   by  
pressing it lightly while turning it
anticlockwise.
-

 
Change
  the   bulb.
When
  removing   the   lamp   unit:
-
 
with
  tailgate,   pull   the   lamp   unit  
towards the centre of the vehicle,
-

 
with
  hinged   doors,   pull   the   lamp  
unit

  towards   you.
For
 
more
 
information
 
on
 
bulbs,
 
refer
 
to
 the
 
"Types
 
of
 
bulb".
1.

Brake lamps / sidelamps


T

ype B,
 
P21/5W
 
-
 
21/5W
2.

Direction indicators


T

ype B,
 
PY21W
 
-
 
21W
 
(amber)
3.

Reversing lamps


T

ype B, P21W - 21W
4.

Foglamps


T

ype B, P21W - 21W
High pressure jet washing When using this type of washing
on stubborn dirt, do not persist on
the
 
headlamps,
 
the
 
other
 
lamps
 
and

 
their
 
edges
 
to
 
avoid
 
damaging
 
their

 
coating
 
and
 
seals. Chapter
  9,   "Changing   a   wheel"  
section.
-


Identify the failed bulb, then open
the

  rear   doors   to   180°.
Chapter
  3,   "Access"   section.
-
 
Remove
  the   two   fixing   bolts   using  
the

  spanner   provided.
-
 
Pull
  the   lamp   unit   from   the   outside.
-
 
Holding
  the   lamp,   disconnect   the  
electrical

  connector.
Changing a bulb

185
Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2016
Number plate lamps
- Unscrew  the   two   nuts.
-  
Push
  the   pins.
-

If necessary
, disconnect the
connector
  to   remove   the   lamp.
-
 
Change
  the   bulb.
Third brake lamp
Type A, W16W - 16W
Type A, W5W - 5W
With tailgate
-
d
isengage the plastic lens using a
screwdriver.
-
 
Change

 
the
 
bulb.
-

Replace the plastic lens and press
on

 
it. With hinged doors
-
 
Unclip

 
the
 
interior
 
trim.
-
d
isconnect the connector by
moving
 
aside
 
its
 
tab.
-

T

urn the bulb holder a quarter turn
anticlockwise.
-
 
Change

 
the
 
bulb.
-
 
Put

 
the
 
bulb
 
holder
 
back
 
in
 
place
 
and

 
reconnect
 
the
 
connector.
-
 
Put

 
the
 
trim
 
back
 
in
 
place.
QUICk HELP
8
Changing a bulb

186
Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2016
CHANGING A FUSE
The fuseboxes are located:
-
in the lower dashboard on the

left-hand side (behind the cover),
-
 
under
  the   bonnet   (near   the   battery).
The
  information   given   concerns   only  
those fuses which can be changed by
the user using the tweezer

, located
behind the dashboard storage
compartment
  on   the   right-hand   side.  
For

  any   other   work,   visit   a   CITROËN  
dealer

  or   a   qualified   workshop.
Removing and fitting a fuse
Always replace a failed fuse with a
fuse of the same rating.
Motor
 
trade
 
technicians:
 
for
 
complete

 
information
 
on
 
the
 
fuses
 
and relays, refer to the "Repair
Manual"

 
diagrams
 
via
 
the
 
dealer
 
network.
CITR

o
Ë
n
will not accept responsibility
for the cost incurred in repairing
your vehicle or for rectifying the
malfunctions
 
resulting
 
from
 
the
 installation of accessories not
supplied
 
and
 
not
 
recommended
 
by
 
the
 
CITROËN

 
network
 
and
 
not
 
installed
 
in accordance with its instructions,
in

 
particular
 
when
 
the
 
combined
 
consumption

 
of
 
all
 
of
 
the
 
additional
 
equipment

 
connected
 
exceeds
 

10
 
milliamperes. Before replacing a fuse, the cause of
the
  incident   must   be   identified   and  
rectified.
●

 
Use
  the   tweezer.
Changing a fuse

187
Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2016
Dashboard fuses
Tilt the cover to gain access to the
fuses.Fuses
F Amperes  Aa
llocation
1 15 Rear wiper
2 -
n

ot used
3 5
a

irbag
4 10 Air
  conditioning,   diagnostic   socket,   mirror   control,  
headlamp

  beam
5 30 Electric windows
6 30 Locks
7 5Rear
  courtesy   lamp,   front   map   reading   lamp,   roof  
console
8 20 Audio

  equipment,   screen,   tyre   under-inflation  
detection,

  alarm   and   siren
9 30Front
  and   rear   12V   socket
10 15 Central
  column
11 15 Low current ignition switch
12 15 Rain and sunshine sensor, airbag
13 5 Instrument
  panel
14 15 Parking
  sensors,   digital   air   conditioning   controls,  
hands-free

  phone   kit
15 30 Locks
16 -
n

ot used
17 40Rear
  screen/mirrors   demist/defrost
QUICk HELP
8
Changing a fuse

188
Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2016
Passenger compartment fuses
Fuses F Amperes
 
Aa
llocation
1 -
n

ot used
2 20 Heated seats
3 -
n

ot used
4 15 Folding
  mirrors   relay
5 15 Refrigeration
  equipment   socket   relay
Changing a fuse

189
Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2016
Fuses under the bonnet
after opening the bonnet, unclip and tilt
the corresponding box to gain access
to
  the   fuses. Fuses
F Amperes  Aa
llocation
1 20 Engine
  management
2 15 Horn
3 10 Front
  and   rear   wash-wipe   pump
4 20 Headlamp
  wash   pump
5 15 Engine
  components
6 10 Steering wheel angle sensor,
d SC
7 10Brake
  switch,   clutch   switch
8 25 Starter
  motor
9 10Headlamp
  beam   motor,   fleet   management   unit
10 30 Engine
  components
11 40
n

ot used
12 30 Wipers
13 40 Built-in
  systems   interface
14 30 Pump
15 10 Right-hand
  main   beam   headlamp
16 10 Left-hand
  main   beam   headlamp
17 15Right-hand
  dipped   beam   headlamp
18 15 Left-hand
  dipped   beam   headlamp
QUICk HELP
8
Changing a fuse

190
Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2016
Placing the windscreen wiper
blades in the special positionChanging a front wiper blade
- Lift
  the   wiper   arm.
-  
Unclip
  the   blade   and   remove   it.
-
 
Fit
  the   new   blade.
-
 
Push
  back   the   wiper   arm.
Changing the rear wiper blade
- Lift  the   wiper   arm,   then   unclip   the  blade
  and   remove   it.
-
 
Fit
  the   new   blade   and   push   back  
the

  wiper   arm.
CHANGING A WIPER BLADE
- Within  a   minute   after   switching   off  the
  ignition,   press   the   wiper   stalk  
downwards to position the wiper
blades along the windscreen pilla

rs
(special
  position). To return the windscreen wipers to
their
  normal   position,   switch   on   the  
ignition

  and   operate   the   wiper   stalk.
Changing a wiper blade