2016 Citroen BERLINGO MULTISPACE 2016

175
Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2016
- Position the wheel on the hub and
start  tightening   the   bolts   by   hand.
-

Carry out an initial tightening of the
bolts

  using   the   wheelbrace.
5. Fitting the spare wheel
- Lower  the   vehicle   completely   by  folding
  the   jack,   then   remove   the  
jack.
-


T
ighten the bolts again using the
wheelbrace,
  tighten   them   fully  
without

  forcing   them.
-

Place the wheel to be repaired in
the

  carrier. -
 Secure   the   carrier   on   the   hook   then  raise the carrier by tightening the
bolt
  with   the   wheelbrace.
-
 
Fully
  tighten   the   bolt,   then   check  
that

  the   wheel   is   held   flat   against  
the

  floor.
If this is not the case, repeat the
operation.
n

ever go underneath a vehicle
that
  is   supported   only   by   a   jack  
(use

  a   stand).
n

ever use a power driver in place of
the
  wheelbrace.
QUICk HELP
8
Changing a wheel

176
Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2016
FITTING THE WHEEL
TRIM
The tyre valve must be centred in the wheel
  trim   cut-out.
This
  position   is   essential   for   fitting   the  
wheel

  trim   correctly   on   the   steel   wheel.  
(If

the valve is not correctly aligned with
the
  cut-out,   the   anti-rotation   system  
will be in contact with the heads of the
wheel

  bolts   and   risks   being   damaged  
if

  the   user   persists   in   fitting   the   wheel  
trim

  in   this   incorrect   position). -

Ensure that all of the clips are
engaged except the last one
(opposite

  the   valve   hole).
-
 
Strike
  the   wheel   trim   with   the   palm  
of your hand, opposite the valve
in

  the   area   of   the   last   fixing   clip  
(always

  in   the   direction   of   clipping).
-

Ensure that the outer edge of
the

  wheel   trim   is   not   deformed   or  
pushed

  into   the   wheel:
●
 
Correct
position for the edge of
the
  wheel   trim.
●
 
Incorrect
position for the edge of
the
  wheel   trim.
6. Refitting the repaired wheel
The wheel is refitted as described in step  5,   not   forgetting   to   refit   the   wheel  
trim.
Refer

  to   the   "Instruments   and  
controls" section of chapter 3,
"T

yre   under-inflation   detection"  
part,

  for   recommendations   after  
changing

  a   wheel   fitted   with   a   tyre  
under-inflation

  detection   sensor.
Refer
  to   the   "Identification  
markings"

  section   of   chapter   9   to  
locate

  the   tyre   label.
The spare wheel is not designed
to
  be   used   over   long   distances.  
Have the tightening of the bolts
and

  the   tyre   pressure   checked   by  
a

  CITROËN   dealer   or   a   qualified  
workshop

  as   soon   as   possible.
Have the original wheel repaired
and
  refitted   by   a   CITROËN   dealer  
or

  a   qualified   workshop   as   soon   as  
possible.
Changing a wheel

177
Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2016
Check the position of the tyre
valve relative to the ring of the
wheel trim.
Valve not positioned correctly:
  below  
the

 
ring. Observe the wheel trim fitting
procedure, so as to avoid
breaking the fixing clip and
deformation at the edge of the
wheel trim.
Deformation
  of   the   edge   of   the   wheel  
trim

  at   the   valve,   because   it   is   fitted  
incorrectly

.Valve positioned correctly:
  below   the  
ring.
QUICk HELP
8
Changing a wheel

178
Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2016
REMOVABLE SNOW SCREEN
(
BLANKING COVER )
According to country, the removable snow screen is installed on the lower
part
  of   the   front   bumper   to   prevent   the  
accumulation

  of   snow   at   the   radiator  
cooling

  fan.
Fitting Removal
- offer up the snow screen facing its
centring pin A   on   the   front   bumper.
-

Put it in place by pressing at each
clip

B   located   in   the   four   corners.
Do
 
not
 
forget
 
to
 
remove
 
the
 
snow screen when the exterior
temperature

 
is
 
higher
 
than
 
10°C
 
(no

 
risk
 
of
 
snowfall)
 
and
 
when
 
towing. -
Pass a screwdriver into the hole
located
  near   each   of   the   clips.
-

Use the screwdriver as a lever to
unclip the four clips

B   in   turn.
Snow screen

179
Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2016
SNOW CHAINS
In wintry conditions, snow chains
improve  traction   as   well   as   the  
behaviour

  of   the   vehicle   when   braking.
 The

  snow   chains   must   be   fitted  
only

  to   the   driving   wheels.  
They
 
must

  never   be   fitted   to   "space-
saver"
  type   spare   wheels.
 T

ake   account   of   the   legislation   in  
force in your country on the use
of

  snow   chains   and   the   maximum  
running

  speed   authorised.Advice on installation
F
 
If
  you   have   to   fit   the   chains   during  
a

  journey,   stop   the   vehicle   on   a   flat  
surface

  on   the   side   of   the   road.
F
 
Apply
  the   parking   brake   and  
position

  any   wheel   chocks   to  
prevent

  movement   of   your   vehicle.
F

Fit the chains following the
instructions provided by the
manufacturer

.
F

Move of
f gently and drive for a
few
  moments,   without   exceeding  
30

  mph   (50   km/h).
F
 
Stop
  your   vehicle   and   check   that  
the snow chains are correctly
tightened.It

  is   recommended   that   before   you  
leave,

  you   practise   fitting   the   snow  
chains

  on   a   level   and   dry   surface.
Use only the chains designed to be
fitted
  to   the   type   of   wheel   fitted   to   your  
vehicle:
For

  more   information   on   snow   chains,  
contact a CITR

o Ë n dealer or a
qualified
  workshop.
o
riginal
tyre size Maximum
  link  
size.
195/65

  R159
  mm
195/70
  R15
205/65
  R15
215/55
  R16
215/50
  R17
avoid driving with chains on roads
that have been cleared of snow

,
to
  avoid   damaging   your   vehicle's   tyres  
and

  the   road   surface.   If   your   vehicle  
is

  fitted   with   alloy   wheels,   check   that  
no

  part   of   the   chain   or   its   fixings   is   in  
contact

  with   the   wheel   rim.
QUICk HELP
8
Snow chains

180
Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2016
CHANGING A BULB
Type A
All  glass   bulb:   pull   gently  
as

  it   is   fitted   by   pressure.
Type C
Halogen
  bulb:   release   the  
retaining

  spring   from   its  
housing. T
ype B
Bayonet
  bulb:   press  
on the bulb then turn it
anticlockwise.
T

ypes of bulb
Various
 
types
  of   bulb   are   fitted   to   your  
vehicle.
T

o
 
remove
 
them:
Type D
Light-emitting   diode  
(LED):

  for   replacement  
of

  the   daytime   running  
lamps,

  contact   a  
CITR

o Ë n dealer or a
qualified
  workshop.
Changing a bulb

181
Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2016
2. Sidelamps
Type A, W5W - 5W
- 
Remove
  the   cover   by   pulling   the  
flexible

  rubber   tab.
-
 
Remove
  the   bulb   holder   fitted   by  
pressure

  by   pulling   the   connector.
-
 
Change
  the   bulb.
-
 
Ensure
  that   the   cover   is   refitted  
correctly all round to assure correct
sealing.
Front lamps
1. Dipped / Main beam headlamps
T ype C, H4 - 55W
-
 
Remove
  the   centre   cover   by   pulling  
the

  flexible   rubber   tab.
-
 
Disconnect
  the   electrical   connector.
-
 
Release
  the   retaining   tab.
-
 
Change
  the   bulb   taking   care  
to

  align   the   metal   part   with   the  
grooves

  on   the   lamp.
-
 
Reposition
  the   retaining   tab.
-
 
Ensure
  that   the   cover   is   refitted  
correctly all round to assure correct
sealing.
High pressure washing Open

 
the
 
bonnet.
 
T

o
 
access
 
the
 
bulbs,
 
reach

 
behind
 
the
 
headlamp
 
unit.
Carry out the operations in reverse
order
 
to
 
refit
 
each
 
bulb
 
and
 
check
 
that
 
the

 
bonnet
 
is
 
closed
 
securely.
Halogen
 
bulbs
 
must
 
be
 
changed
 
with

 
the
 
headlamp
 
off.
 
Wait
 
a
 
few
 
minutes

 
(risk
 
of
 
serious
 
burns).
 
d
o not touch the bulb directly with your
fingers,
 
use
 
lint-free
 
cloths.
It
 
is
 
normal
 
for
 
condensation
 
to
 
form
 
inside

 
the
 
headlamps.
 
Regular
 
use
 
of
 the
 
vehicle
 
eliminates
 
this
 
misting.
The
 
bulbs
 
must
 
be
 
changed
 
with
 
the ignition of

f or with the battery
disconnected.
 
Wait
 
approximately
 
3 minutes

 
after
 
changing
 
the
 
bulb
 
before

 
reconnecting
 
the
 
battery.
Check
 
that
 
the
 
lamps
 
operate
 
correctly
 
after

 
each
 
operation.
When using this type of washing
on stubborn dirt, do not persist on
the
 
headlamps,
 
the
 
lamps
 
and
 
their
 
edges

 
to
 
avoid
 
damaging
 
their
 
coating
 
and

 
seals.
QUICk HELP
8
Changing a bulb

182
Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2016
3. Direction indicators
Type B,  PY21W   -   21W   (amber)
-
 
Remove
  the   cover   by   pulling   the  
flexible

  rubber   tab.
-

T
urn the bulb holder a quarter turn
anticlockwise.
-
 
Remove
  the   bulb   by   pressing   it  
lightly

  while   turning   it   anticlockwise.
-
 
Change
  the   bulb.
-
 
Ensure
  that   the   cover   is   refitted  
correctly all round to assure correct
sealing. 4. Front foglamps
T

ype C, H1 - 55W
-
 
Remove
  the   three   clips   and   the  
screw securing the wheel arch liner

,
located
  below   the   bumper.
-
 
Move
  the   wheel   arch   liner   upwards.
-
d isconnect the bulb holder
connector by pressing the tab at
the
  top.-
 
Remove
  the   bulb   holder   by  
squeezing the two clips (at top and
bottom)

  using   a   finger   and   thumb.
-
 
Replace
  the   module   (bulb   holder  
and

  bulb).
-

Carry out the operations in reverse
order

  to   fit   the   module   and   refit   the  
wheel

  arch   liner.
Changing a bulb