
Addendum
having this work performed by a service  
center as it is important that this safety fea-
ture functions properly.” 
10. At page 160 under the heading: “Objects  
within the range of movement of the ped-
als” and at page 207 under the heading: 
“Carpets and floor mats,” the paragraph 
that begins: “Only use floor mats  …” should 
be disregarded and the following language 
should be read in lieu thereof: “The manu-
facturer of your vehicle recommends that 
you use floor mats that have been identified 
by it as appropriate for use in your vehicle 
and that can be properly fixed in place.” 
11. At page 165, under the heading: “Have  
maintenance carried out,” the sentence 
beginning, “The maintenance should be 
carried out …” should be disregarded and 
the following text should be read in lieu 
thereof:   “BMW recommends that you have  
the maintenance carried out by your service 
center.” 
12. At page 172, under the heading “Tire infla- 
tion specifications,” the sentence begin-
ning, “Tire inflation pressure specifications 
apply to approved tire sizes …” should be 
disregarded. 
13. At page 176, under the heading: “Mount- 
ing,” the paragraph beginning, “Have 
mounting and balancing …” should be dis-
regarded and the following text should be 
read in lieu thereof: “BMW recommends 
that you have mounting and balancing per-
formed by your service center or a tire 
mounting specialist.” 
14. At page 176, under the heading: “Approved  
wheels and tires,” the term “Approved” 
should be disregarded and in lieu thereof, 
the term “Recommended” should be read 
in its place. In addition, the text of that sec-
tion should be disregarded and the follow-
ing text should be read in lieu thereof:  
The manufacturer of your vehicle strongly  
suggests that you use wheels and tires that 
have been recommended by the vehicle  
manufacturer for your vehicle type; other- 
wise, for example, despite having the same 
official size ratings, variations can lead to 
body contact and with it, the risk of severe 
accidents.  
The manufacturer of your vehicle does not  
evaluate non-recommended wheels and 
tires to determine if they are suitable for use 
on your vehicle. 
15. At page 180, under the heading: “Snow  
Chains,” the text should be disregarded and 
the following text should be read in lieu 
thereof:  
Only certain types of fine-link snow chains  
have been tested by the manufacturer of 
your vehicle and are determined by the 
manufacturer of your vehicle to be road safe 
and are recommended by the manufacturer 
of your vehicle.  
Information about recommended snow  
chains is available from a service center. 
16. At page 181, under the heading “Hood,” the  
sentence beginning, “If you are unfamiliar” 
should be disregarded. 
17. At page 185, under the heading: “Engine oil  
change,” the text should be disregarded 
and in lieu thereof should be read as follows: 
BMW recommends that you have the oil  
changed at your BMW dealer's service cen-
ter or at another service center that has 
trained personnel that can perform the work 
in accordance with BMW specifications. 
18. At page 188, under the heading: “Service  
and Warranty Information Booklet for US 
models and Warranty and Service Guide 
Booklet for Canadian models,” the second 
paragraph should be disregarded and the 
following text read in lieu thereof:  
The manufacturer of your vehicle recom- 
mends that you have maintenance and 
repair performed by your BMW dealer's ser-
vice center or another service center or 
repair shop that employs trained personnel 
that can perform maintenance and repair  
Online Edition for Part no. 01 40 2 960 812 - II/15 

BMW M4 technologyVehicle features and options
This chapter describes all standard, country-
specific and optional features offered with the
series. It also describes features that are not
necessarily available in your car, e. g., due to
the selected options or country versions. This
also applies to safety-related functions and
systems. The respectively applicable country
provisions must be observed when using the
respective features and systems.
High-performance engine The high-performance engine gets a maximum
power of 317 kW and maximum torque of
550 Nm from a displacement of 3 liters. With
its spontaneous response behavior, a speed
range of wide utility results. The maximum en‐
gine speed is 7,600 rpm and is electronically
controlled. Because of the high engine dynam‐
ics, the maximum engine speed with the vehi‐
cle stationary is reduced.
Warm-up During the engine warm-up phase, the high-performance engine has a somewhat rougher
running behavior because of the emission con‐
trols.
When the engine is cold, the exhaust system
has a slightly metallic undertone due to the na‐
ture of the system.
For more information about the warm-up pro‐
cedure: Engine speed, refer to page  81, and
engine oil temperature, refer to page  81.
Compound brake
The high-performance braking system has
perforated compound brake discs.Because of particular structural characteristics,
there may be operation-related noises during
braking. However, this has no effect on per‐
formance, operational reliability and reliability
of the brake.
Correct brakingTo keep the brake system in optimum condi‐
tion, it is expedient to apply them at regular in‐
tervals corresponding to the vehicle character.
M carbon ceramic brake The high-performance braking system has
perforated carbon-ceramic brake disks and is
designed for use on racetracks.
Due to properties of the materials used, brak‐ ing may be associated with louder function
noises, particularly in wet conditions, just be‐
fore the vehicle comes to a stop. However, this
has no effect on the performance, operational
reliability and durability of the brake.
The effects of moisture and road salt, from us‐
ing a carwash or dew formation overnight e.g.,
may render the braking effect comparable to
that of a conventional braking system. This
may be perceived as reduced braking effect
and can be compensated for if needed by
pressing the brake pedal harder.
Before washing the vehicle in an automatic
carwash or wash tunnel, clean the brake discs
and brake calipers with a steam jet or high-
pressure washer as well, to prevent encrusta‐
tions and dirt buildups, caused by salt crystals,
e.g., if the car is immobile afterwards. The
cleaning effect of automatic carwashes or
wash tunnels is usually not adequate for this in
the area around the wheels.
To do this, also follow the instructions in
Washing the vehicle, refer to page  204, and
Braking safely, refer to page  159.Seite 156Driving tipsBMW M4 technology156
Online Edition for Part no. 01 40 2 960 812 - II/15 

Retreaded tires
Possibly substantial variations in the de‐
sign and age of the tire casing structures can
limit service life and have a negative impact on
road safety.◀
Winter tires
Winter tires are recommended for operating on
winter roads.
Although so-called all-season M+S tires pro‐
vide better winter traction than summer tires, they do not provide the same level of perform‐
ance as winter tires.
Maximum speed of winter tires If the maximum speed of the vehicle is higher
than the permissible speed for the winter tires,
then a respective symbol is displayed in your
field of vision. You can obtain this sign from the
tire specialist or from your service center.
Maximum speed for winter tires
Do not exceed the maximum speed for
the respective winter tires; otherwise, tire dam‐
age and accidents can occur.◀
Rotating wheels between axles The manufacturer of your vehicle advises
against switching wheels between the front
and rear axles. This can impair the handling
characteristics.
Rotating the tires is not permissible on vehi‐
cles with different tire sizes or rim sizes on the
front and rear axles.
StorageStore wheels and tires in a cool, dry place with
as little exposure to light as possible.
Always protect tires against all contact with oil,
grease and fuels.
Do not exceed the maximum tire inflation pres‐
sure indicated on the side wall of the tire.Mobility System
The concept
With the Mobility System, minor tire damage
can be sealed quickly to enable continued
travel. To accomplish this, sealant is pumped
into the tires, which seals the damage from the
inside.
The compressor can be used to check the tire
inflation pressure.
Hints▷Follow the instructions on using the Mobi‐
lity System found on the compressor and
sealant container.▷Use of the Mobility System may be ineffec‐
tive if the tire puncture measures approx.
1/8 in/4 mm or more.▷Contact the nearest service center if the
tire cannot be made drivable.▷If possible, do not remove foreign bodies
that have penetrated the tire.▷Pull the speed limit sticker off the sealant
container and apply it to the steering
wheel.▷The use of a sealant can damage the TPM
wheel electronics. In this case, have the
electronics checked at the next opportu‐
nity and have them replaced if needed.
Enclosed areas
Do not let the engine run in enclosed
areas, since breathing in exhaust fumes may
lead to loss of consciousness and death. The
exhaust gases contain carbon monoxide, an
odorless and colorless but highly toxic gas.◀
Storage The Mobility System is located under the
cargo floor panel.
Seite 177Wheels and tiresMobility177
Online Edition for Part no. 01 40 2 960 812 - II/15 

CareVehicle features and optionsThis chapter describes all standard, country-
specific and optional features offered with the
series. It also describes features that are not
necessarily available in your car, e. g., due to
the selected options or country versions. This
also applies to safety-related functions and
systems. The respectively applicable country
provisions must be observed when using the
respective features and systems.
Car washes General information
Regularly remove foreign objects such as
leaves in the area below the windshield when
the hood is raised.
Wash your vehicle frequently, particularly in
winter. Intense soiling and road salt can dam‐
age the vehicle.
Hints Steam jets or high-pressure washers
When using steam jets or high-pressure
washers, hold them a sufficient distance away
and use a maximum temperature of
140 ℉/60 ℃.
Holding them too close or using excessively
high pressures or temperatures can cause
damage or preliminary damage that may then lead to long-term damage.
Follow the user's manual for the high-pressure
washer.◀
Cleaning sensors/cameras/hardtop with
high-pressure washers
When using high-pressure washers, do not
spray the seals of the lowerable hardtop, sen‐
sors and cameras external to the vehicle, e.g.,Park Distance Control, for extended periods of
time and only from a distance of at least
12 in/30 cm.◀
Automatic car washes
Hints Do not use high pressure washing sys‐
tems
With washing systems operating at high pres‐
sures and nozzle positions close to the win‐
dows, drops of water can penetrate.◀▷Give preference to cloth car washes or
those that use soft brushes in order to
avoid paint damage.▷Make sure that the wheels and tires are not
damaged by the transport mechanisms.▷Fold in the exterior mirrors; otherwise, they
may be damaged, depending on the width
of the vehicle.▷Deactivate the rain sensor, refer to
page  69, to avoid unintentional wiper acti‐
vation.▷In some cases, an unintentional alarm can
be triggered by the interior motion sensor
of the alarm system. Follow the instruc‐
tions on avoiding an unintentional alarm,
refer to page  45.
Guide rails in car washes
Avoid car washes with guide rails higher
than 4 in/10 cm; otherwise, the vehicle body
could be damaged.◀
Before driving into a car wash In order to ensure that the vehicle can roll in a
car wash, take the following steps:
Seite 204MobilityCare204
Online Edition for Part no. 01 40 2 960 812 - II/15 

Everything from A to Z
IndexA ABS, Antilock Brake Sys‐ tem  116 
Acceleration Assistant, refer to Launch Control  74 
Accessories and parts  7 
Activated-charcoal filter  139 
Active Blind Spot Detec‐ tion  113 
Active M differential  119 
Adaptive brake lights, refer to Brake force display  115 
Adaptive Light Control  95 
Adaptive M chassis  119 
Additives, oil  185 
Adjustments, seats/head re‐ straints  52 
After washing vehicle  205 
Airbags  99 
Airbags, indicator/warning light  100 
Air circulation, refer to Recir‐ culated-air mode  138 
Air, dehumidifying, refer to Cooling function  137 
Air distribution, manual  138 
Air flow, automatic climate control  138 
Air pressure, tires  172 
Air vents, refer to Ventila‐ tion  139 
Alarm system  44 
Alarm, unintentional  45 
All around the center con‐ sole  16 
All around the roofliner  17 
All around the steering wheel  14 
All-season tires, refer to Win‐ ter tires  177 Alternating-code hand-held
transmitter  142 
Alternative oil types  185 
Ambient light  97 
Antifreeze, washer fluid  70 
Antilock Brake System, ABS  116 
Anti-slip control, refer to DSC  117 
Anti-theft protection, see through-loading sys‐
tem  149 
Approved axle load  210 
Approved engine oils, see Suitable engine oil
types  185 
Arrival time  88 
Ash tray  145 
Assistance when driving off  120  
Attentiveness assistant  115 
AUTO intensity  137 
Automatic car wash  204 
Automatic climate con‐ trol  136  
Automatic Curb Monitor  58 
Automatic deactivation, front- seat passenger airbags  101 
Automatic headlight con‐ trol  95 
Automatic locking  43 
Automatic recirculated-air control  138 
AUTO program, automatic cli‐ mate control  137 
AUTO program, intensity  137 
Auto Start/Stop function  65 
Average fuel consumption  88 
Average speed  88 
Axle loads, weights  210 B
Backrest curvature, refer to Lumbar support  53 
Backrest, width  53 
Band-aids, refer to First aid kit  199  
Bar for tow-starting/ towing  202 
Battery replacement, vehicle battery  195 
Battery replacement, vehicle remote control  35 
Battery, vehicle  195 
Belts, safety belts  55 
Beverage holder, cu‐ pholder  153 
BMW Assist, see user's manual for Navigation, En‐
tertainment and Communi‐
cation 
BMW Driver’s Guide App  6 
BMW Homepage  6 
BMW Internet page  6 
BMW maintenance sys‐ tem  188 
BMW M technology  156 
Bottle holder, refer to Cu‐ pholders  153 
Brake assistant  116 
Brake discs, break-in  158 
Brake force display  115 
Brake lights, adaptive  115 
Brake lights, brake force dis‐ play  115 
Brake pads, break-in  158 
Braking, hints  159 
Breakdown assistance  198 
Break-in  158 
Brightness of Control Dis‐ play  91 Seite 212ReferenceEverything from A to Z212
Online Edition for Part no. 01 40 2 960 812 - II/15 

External temperature warn‐ing  82 
Eyes for securing cargo  163 
F
Failure message, see Check Control  78 
False alarm, refer to Uninten‐ tional alarm  45 
Fan, refer to Air flow  138 
Filler neck for engine oil  184 
Fine wood, care  206 
First aid kit  199 
Fitting for towing, see Tow fit‐ ting  202 
Flat tire, changing wheels  195 
Flat tire, Tire Pressure Moni‐ tor TPM  103 
Flat tire, warning lamp  104 
Flooding  159 
Floor carpet, care  207 
Floor mats, care  207 
Fold down the rear seat back‐ rest, see Though-loading
system  149 
Fold-out position, wiper  70 
Foot brake  159 
Front airbags  99 
Front-end collision warning with City Braking func‐
tion  107 
Front lights  191 
front-seat passenger airbags, automatic deactivation  101 
Front-seat passenger airbags, indicator lamp  101 
Fuel  170 
Fuel consumption, current  83 
Fuel consumption, refer to Average fuel consump‐
tion  88 
Fuel filler flap  168 
Fuel gauge  81 
Fuel lid  168 Fuel quality  170 
Fuel recommendation  170 
Fuel, tank capacity  211 
Fuse  196 
G
Garage door opener, refer to Universal Integrated Remote
Control  141 
Gasoline  170 
Gear change  73 
Gear shift indicator  85 
General driving notes  159 
Glare shield  145 
Glove compartment  151 
Gross vehicle weight, ap‐ proved  210 
Ground clearance  160 
H
Handbrake, refer to parking brake  67 
Hand-held transmitter, alter‐ nating code  142 
Hardtop  46 
Hardtop, rollover protection system  102 
Hardtop, trunk partition  49 
Hazard warning flashers  198 
Headlight control, auto‐ matic  95 
Headlight courtesy delay fea‐ ture  94 
Headlight flasher  68 
Headlight glass  191 
Headlights  191 
Headlights, care  205 
Headlight washer system  68 
Head restraints  52 
Head restraints, front  56 
Head-up Display  91 
Head-up Display, care  207 
Head-up display, M view  92 Head-up display, standard
view  91 
Heating, neck  54 
Heavy cargo, stowing  163 
Height, vehicle  210 
High-beam Assistant  96 
High beams  68 
High beams/low beams, refer to High-beam Assistant  96 
High-performance en‐ gine  156 
Hills  160 
Hill start assistant, refer to Drive-off assistant  120 
Hints  6 
Holder for beverages  153 
Homepage  6 
Hood  181 
Horn  14 
Hot exhaust system  159 
HUD Head-up Display  91 
Hydroplaning  159 
I
Ice warning, see External temperature warning  82 
Icy roads, see External tem‐ perature warning  82 
Identification marks, tires  173 
Identification number, see ve‐ hicle identification num‐
ber  9 
iDrive  18 
Ignition key, refer to Remote control  34 
Ignition off  63 
Ignition on  63 
Indication of a flat tire  104 
Indicator and alarm lamps, see Check Control  78 
Indicator lamp, see Check Control  78 
Individual air distribution  138 
Individual settings, refer to M Drive  116 Seite 215Everything from A to ZReference215
Online Edition for Part no. 01 40 2 960 812 - II/15