2016 AUDI TT ROADSTER ignition

Downloaded from www.Manualslib.com manuals search engine maximum
manoeuvring speed is 5 km/h. The
park assist will be deactivated if you drive too
fast or move the steering wheel by hand. To con­
tinue the parking manoeuvre, switch the engine
off/on. Then press the I@ button again. Alterna­
tively, drive out of the parking space without us­
ing the park assist.
Driver messages
Applies to: vehicles with park assist
Iii! Park assist: steering assistance active.
Please drive slowly and operate the brakes your­
self
The park assist is ready. You can now park the ve­
hicle. Watch the road ¢ & in Description on
page 108.
Ill Park assist: ended. Please take over steer­
ing.
The park assist has finished the parking manoeu­
vre.
Ill Park assist: cancelled. Continue steering ve­
hicle!
The park assist has interrupted the parking ma­
noeuvre to avoid a collision between the vehicle
and an obstacle.
Ill Park assist: cancelled. Steering input detec­
ted. Continue steering vehicle!
The steering assistant has been deactivated be­
cause the driver has intervened in the steering.
To continue the parking manoeuvre, press the
I@ button again.
[9] Reduce your speed! For the best results when
passing the line of parked cars where you want to
park, do not drive faster than 30 km/h (if parking
parallel to the roadside) or 20 km/h (if parking
perpendicular to the roadside) ¢ page 109.
Ill Park assist: cancelled. Speed too high. Con­
tinue steering vehicle!
You were driving too fast into the parking space.
Do not exceed 7 km/h when driving into the park-
� ing space.
� Ill
Park assist: currently unavailable. Stabilisa­
o
[;:j tion
control (ESC) off Parking aids
Switch the ES( on to use the park assist.
Iii! To leave parking space select reverse gear
and operate turn signal
The park assist is ready. You can leave the park­
ing space. Watch the road ¢ & in Description on
page 108.
Ill Park assist: cancelled. Stabilisation control
(ESC) input. Continue steering vehicle!
Take over the steering. Finish parking without
the park assist or drive out of the parking space.
The park assist has interrupted the parking ma­
noeuvre, because the ESC has been switched off.
Take over the steering or switch on the ESC
¢page 114 and start the parking manoeuvre
again ¢page 109.
Ill Park assist: ended. Please take over steering
and continue driving.
The park assist has finished manoeuvring the ve­
hicle out of the parking space. Please take over
the steering.
Ill Park assist: cancelled. Space too small
The assist function is unable to automatically
steer the vehicle out of the parking space be­
cause the space is too small. Manoeuvre the vehi­
cle out of the parking space without using the
park assist.
Ill Park assist: time limit exceeded
Ill Park assist: cancelled. Time limit exceeded.
Continue steering vehicle!
The parking manoeuvre was not completed with­
in about six minutes after the park assist was ac­
tivated. To continue the parking manoeuvre,
press the I@ button again.
Ill Park assist: currently unavailable
Ill Park assist: currently unavailable. Continue
steering vehicle!
The park assist cannot be used to park the vehi­
cle. Try repeating the parking manoeuvre or
switching the ignition off and on again.
Ill Park assist: not stopped long enough
Ill-
111

Downloaded from www.Manualslib.com manuals search engine Parking
aids
After you select reverse gear, the vehicle has to
remain stationary for a moment so that the park
assist can activate the steering. Follow the direc­
tions given in the display.
II Park assist: fault. Please contact workshop
Ill Park assist: fault. Continue steering vehicle!
Please contact workshop
Please contact a qualified workshop. The park as­
sist cannot be used to park the vehicle if a system
fault occurs.
II Park assist: cancelled. Space too small. Con­
tinue steering vehicle!
The park assist cannot be used to park the vehicle
in this space. Park the vehicle without using the
park assist or look for a bigger space.
Adjusting graphic display
and warning beeps
Applies to: vehicles with parking system plus/park assist
The settings for the graphic display and acoustic
signals are controlled via the infotainment sys­
tem.
.. Select the following on the infotainment sys­
tem: I MENU I button > Car > left control button
> Driver assist> Parking aid.
Warning beeps
Front volume -Volume for the front and side*
zones
Rear volume -Volume for the rear zone
In-car entertainment fader -The volume of the
current audio or video source is reduced when the
parking aid is switched on.
You will hear a short test tone each time you
make a new setting.
� Note
The settings will be automatically stored and
assigned to the remote control key in use.
112 Fault
warnings
Applies to: vehicles with rear parking aid/parking system
plus/park assist
Rear parking aid: fault. Obstacles cannot be de­
tected
Parking aid: fault. Obstacles cannot be detected
If the LED in the P,J1A button starts flashing when
you switch the system on, a system fault has oc­
curred. If the fault is not corrected before you
switch off the ignition, it will only be indicated by
the flashing LED in the P'),IA button the next time
you switch on the parking aid by engaging re­
verse gear. The fault warning can be displayed in
the second tab of the driver information system
as long as the fault is active.
Parking system plus*/parking system plus
and park assist*
If a sensor or loudspeaker malfunctions, the�
symbol will be shown on the infotainment sys­
tem in front of or behind the vehicle. If a rear
sensor malfunctions, obstacles will only be dis­
played in zones (D and @ ¢page 104, Fig. 106.
If a front sensor malfunctions, obstacles will only
be displayed in zones @ and @ .
Drive to a qualified workshop soon and have the
fault rectified.

Downloaded from www.Manualslib.com manuals search engine Intelligent
technology
A WARNING
When extending or retracting the rear spoiler,
please make sure that no persons or objects
are close to the moving spoiler -risk of injury!
CD CAUTION
- If you need to push the vehicle, never put
your weight on the rear spoiler -Risk of
damage!
- To avoid damage to the rear spoiler, you
should not lean on it or apply any other type
of pressure.
- Do not operate the rear spoiler manually
when the boot lid is open or any moving
parts of the automatic rear spoiler are ob­
structed -risk of damage!
Note
Clean the rear spoiler housing every 2 to 3
months. The rear spoiler housing must be
free of ice, snow and leaves in order to oper­
ate correctly.
Power management
This system helps to ensure reliable
starting
The power management controls the distribu­
tion of electrical energy and thus helps to ensure
that there is always enough power available to
start the engine.
If a vehicle with a conventional electrical system
is left parked for a long time, the vehicle battery
will gradually lose its charge because certain
electrical equipment (such as the immobiliser)
continues to draw current even when the ignition
is off. In some cases there may not be enough
power available to start the engine.
Your vehicle is equipped with an intelligent pow­
er management system to control the distribu­
tion of electrical energy. This significantly im­
proves reliability when starting the engine, and
also prolongs the life of the vehicle battery.
The main functions incorporated in the power
management system are battery diagnosis, re-
118 sidual
current management and dynamic power
management.
Battery diagnosis
The battery diagnosis function constantly regis­
ters the condition of the vehicle battery. Sensors
detect the battery voltage, battery current and
battery temperature. This enables the system to
calculate the current power level and charge con­
dition of the vehicle battery.
Residu al current management
The residual current management reduces power
consumption while the vehicle is parked. It con­
trols the supply of power to the various electrical
components while the ignition is switched off.
The system takes the battery diagnosis data into
consideration.
Depending on the power level of the vehicle bat­
tery, the individual electrical components are
switched off one after the other to prevent the
vehicle battery from losing too much charge and
to ensure that the engine can be started reliably.
Dynamic power management
While the vehicle is moving, this function distrib­
utes the available power to the various electrical
components and systems according to their re­
quirements. It ensures that on-board systems do
not consume more electrical power than is being
generated, and thus maintains the maximum
possible vehicle battery power level.
.
1 Note
- The power management system is not able
to overcome the given physical limits.
Please remember that the power and life of
the vehicle battery are limited.
- If the indicator lamp ri'.J ¢ page 15 appears,
the starting ability may be impaired.
Points to remember
Starting ability has first priority.
Short trips, city traffic and low temperatures all
place a heavy load on the vehicle battery. In
these conditions a large amount of power is

Downloaded from www.Manualslib.com manuals search engine 0
0
N
,.....
N
......
0
,.....
Vl
CX) consumed,
but only a small amount is supplied.
The situation is also critical if electrical equip­
ment is in use when the engine is not running. In
this case power is consumed when none is being
generated.
In these situations you will be aware that the
power management system is intervening to con­
trol the distribution of electrical power.
When the vehicle is parked for long periods
If you do not drive your vehicle for a period of
several days or weeks, the power management
will gradually shut off the on-board systems one
by one, or reduce the amount of current they are
using. This limits the amount of power consumed
and helps to ensure reliable starting even after a
long period. Certain convenience features, such
as remote control unlocking, may not be availa­
ble. These functions will be restored when you
switch on the ignition and start the engine.
With the engine switched off
If you listen to the radio or use the other info­
tainment functions when the engine is not run­
ning, this will discharge the vehicle battery.
The infotainment display will show a warning
message before the battery power drops to a lev­
el where the starting ability is impaired. This
message warns you that the system you are using
will soon be switched off automatically. You
should therefore start the engine if you wish to
continue using the system.
When the engine is running
Although the alternator generates electrical
power, the vehicle battery can still become dis­
charged while the vehicle is being driven. This can
occur when a lot of power is being consumed but
only a small amount supplied, especially if the
vehicle battery is not fully charged initially.
To restore the necessary energy balance, the sys­
tem will then temporarily shut off the electrical
components that are using a lot of power, or re­
duce the current they are consuming. Heating
systems in particular use a large amount of elec­
trical power. If you notice, for instance, that the
seat heating* or the rear window heater is not Intelligent
technology
working, they may have been temporarily switch­
ed off or regulated to a lower heat output. These
systems will be available again as soon as suffi­
cient electrical power is available.
You may also notice that the engine runs at a
slightly faster idling speed. This is quite normal,
and no cause for concern. The increased idling
speed allows the alternator to meet the greater
power requirement and charge the vehicle bat­
tery at the same time.
Information saved in the
control units
The vehicle is fitted in the factory with electronic
control units that, among other things, control
the engine and the gearbox. The control units al­
so monitor the exhaust system and the airbags.
The control units continually analyse data rele­
vant to the vehicle while you are driving. In the
event of faults or anomalies in the vehicle data,
only these data are saved. As a rule, faults are
shown by the warning lamps in the instrument
cluster.
Data saved in the control units can only be read
and analysed with special equipment.
A qualified workshop is only able to recognise
and deal with faults by using the relevant saved
data. Among other things, the saved data may
contain the following information:
- Data relating to the engine and the gearbox
-Speed
- Direction of travel
- Braking force
- Seat belt warning system data
The control units installed will not under any cir­
cumstances record conversations in the vehicle.
Event data recorder
Your vehicle is not equipped with an event data
recorder.
In an event data recorder, information about
the
vehicle is temporarily saved. In the event of an
accident, you can therefore obtain detailed infor-
mation about the course of events. On vehicles ...,.
119

Downloaded from www.Manualslib.com manuals search engine Multi
Media Interface
Notes on traffic safety
You should only use certain infotainment system
functions, e.g. enter a navigation destination,
while the vehicle is stationary. Always be pre­
pared to stop operating the infotainment system
in the interest of your own safety and that of oth­
er road users.
A WARNING
Only operate the infotainment system when
the traffic conditions allow you to do so safely
and when you can maintain proper control of
your vehicle -risk of accident!
(©) Note
Certain functions are not available while the
vehicle is in motion.
Introduction The Multi Media Interface (MMI) combines dif­
ferent communication, navigation* and enter­
tainment systems in your Audi. You can operate
your MMI system via the MMI control console,
the multi-function steering wheel or the speech
dialogue system*.
Fig. 123 MMI control console
Overview of MMI control console
CD Rotary pushbutton with joystick
function .................... .
@ MMI touch pad* ............. .
o @
Left control button ........... . 122
124
123
123
� @
Right control button .......... .
8 ®
Buttons for calling up menus di-
� rectly ...................... . 122 Multi
Media Interface ® !
MENU! button
0
I BACK! button
122
122
MMI ON/OFF button
with joystick function
How to use
Fig. 124 MMI ON/OFF button with joystick function
Switching the MMI system on/off:
The MMI can be switched on/off manually. l?l
:;;
:i:
<(
a:
- To switch on manually: Briefly press the ON/
OFF button CD¢ Fig. 124. Or: Press the I
MENU!
button ®
¢page 121, Fig. 123 or one of the
buttons for calling up menus directly ®
¢ page 121, Fig. 123.
- To switch off manually: Press and hold the ON/
OFF button CD¢ Fig. 124 until the MMI
switches off. The MMI system will not be
switched on automatically when the ignition is
switched on if it was turned off manually the
last time it was operated.
Other functions:
- To adjust the volume: Turn the ON/OFF button
CD ¢ Fig. 124.
- To mute: Briefly press the ON/OFF button.
- To select the previous/next function (e.g. ra-
dio station/track): Briefly press the ON/OFF
button to the left ll>I.
- To rewind/fast forward (e.g. track): Press and
hold the ON/OFF button to the right l>l>I or left
l A WARNING
The audio system volume should be set at a
level which enables you to hear external
121

Downloaded from www.Manualslib.com manuals search engine 0
0
N
,.....
N
....
0
,.....
Vl
CX) Speech
dialogue system
How to use the speech
dialogue system
Applies to: vehicles with speech dialogue system
You can operate many infotainment functions
conveniently by voice.
Important: The ignition and the MMI system
must be switched on, you must not be talking on
the phone, and the parking aid must not be ac­
tive.
� To switch on: Briefly press the [2!l button @ on
the multi-function steering wheel¢ page 23,
Fig. 10 and give a spoken command after the
beep signal.
� To switch off: Press and hold the [2!l button for
several seconds. Or: Say the command Cancel.
� To pause: Say the command Pause. To end the
pause, press the [2!l button.
� To make a correction: Press the� button once
® ¢page 21, Fig. 8. Or: Say the command Cor­
rection.
Input help
The system guides you through the input routine
with cues and messages.
- Input help messages on screen: After the
speech dialogue system is switched on, a selec­
tion of possible commands will be shown. The
command display can be switched on/off via
IM ENU I
> Settings > left control button > MMI
settings > Speech dialogue system.
- Spoken input help cues: To have the system
play the commands currently possible, press
the [2!l button on the multi-function steering
wheel and say Help.
How to help the system understand you
Speak clearly in a normal volume. Speak louder if
you are driving fast.
Speak in a normal tone without long pauses.
Avoid speaking when the speech dialogue system
is saying a cue. Speech
dialogue system
Close doors and windows and soft top* to reduce
background noise. Make sure that passengers are
not talking when you say a command.
Keep the air outlets of the air distribution system
pointed away from the microphone, which is fit­
ted in the vicinity of the front interior lights in
the headliner/on the driver's seat belt*. For more
information about the seat belt microphone, re­
fer to¢ page 157.
The system should only be operated by the driv­
er, since the handsfree microphone is directed
towards the driver.
Other settings
Refer to¢ page 218, Speech dialogue system.
&_ WARNING
- Please direct your full attention to the road
at all times! As the driver, you have full re­
sponsibility for the safety of the vehicle and
other road users. For this reason, you should
only use the functions in a manner that al­
lows you to maintain control of the vehicle
in all situations -accident risk!
- The speech dialogue system must not be
used in cases of emergency, since the voice
changes in stressful situations. This could
result in a failed or delayed telephone con­
nection. Always dial emergency numbers
manually!
(@ Note
- The dialogue is paused when an incoming
telephone call is received; you can continue
the dialogue by ignoring the call. If you an­
swer the call, the dialogue will be cancelled.
- No navigation cues* or traffic announce­
ments* are played when a dialogue is active.
- You can select an entry from a list both via
the speech dialogue system and using the
rotary pushbutton.
- The speech dialogue system does not sup­
port commands in Arabic, Norwegian or
Hungarian.
133

Downloaded from www.Manualslib.com manuals search engine CD
CAUTION
Please always observe the information ¢(0 in
Wi-Fi hotspot on page 166.
Natural commands
Applies to: vehicles with speech dialogue system Speech
dialogue system
The following overview shows a selection of commands that enable you to speak more naturally with
your vehicle.
• I want to talk to John Smith.
• Who did I call lately?
• Who called me last?
• Call the last number.
• I
would like to go to (XY).
• How much longer to go?
• Show me the traffic on the map.
RAD IO
• Please select BBC.
• What's
my most recent station?
Fig. 139 Natural commands
ijj} Note
The natural commands are not available for
all languages.
External speech dialogue system
Applies to: vehicles with external speech dialogue system
Important: The ignition and the MMI system must be switch­
ed on.
You must not be speaking on the phone.
The parking aid and the Audi speech dialogue sys­
tem must not be active.
A mobile phone must be connected to the MMI
system via the Handsfree profile¢ page 141.
The mobile phone connected must feature a
speech dialogue function that can be controlled
� externally.
� � To switch on: Press and hold the@!l button on
[;:j the
multi-function steering wheel and give a •
How far can the fuel get us?
• Nearest restaurant.
• I'm hungry. Let's eat.
MEDIA
• Play my favourite music.
• What artists have I got?
spoken command after the external speech dia­
logue system has been activated.
� To resume a dialogue: Press the @!l button if
necessary and say a new command. Or: Select
and confirm Continue on the MMI control con­
sole.
� To restart a dialogue: After a dialogue has
been ended, the system remains active for a
short period during which you can start a new
dialogue at any time. Briefly press the @!l but­
ton. Or: Select and confirm Restart speech dia­
logue on the MMI control console.
� To switch off: Press and hold the @!l button for
several seconds. Or: Select and confirm Cancel
on the MMI control console.
@ Note
- No navigation cues* or traffic announce­
ments* are played when a dialogue is active.
- This function depends on the mobile phone
you are using. For further information re­
garding your mobile phone, contact your
mobile network service provider or refer to
..,_
139

Downloaded from www.Manualslib.com manuals search engine Telephone
- We recommend using the vehicle's Wi-Fi
hotspot when the car phone is in use so that
your mobile phone's apps retain access to
the Internet.
Setting up
Connecting a mobile phone via Bluetooth
Applies to: vehicles with telephone
Fig. 140 PIN display for entry on mobile phone
Important
The vehicle must be stationary, and the ignition
must be switched on.
The Bluetooth function and the discoverability
option of the MMI system ¢page 215 and the
mobile phone must be activated.
The mobile phone you would like to connect must
not be connected actively to any other Bluetooth
device.
The MMI must not be connected to a mobile
phone.
A mini SIM card must not be inserted in the SIM
card reader*.
Connecting a mobile phone
... Select: I MENU I button >Telephone > Connect
mobile phone> Continue. The available Blue­
tooth devices will be shown on the infotain­
ment display. Or: Search for the MMI system
via the Bluetooth device search function on
your mobile phone.
... Select and confirm the desired mobile phone
from the list of Bluetooth devices shown.
l l
Not available in all markets. Applies to mobile phones
with Bluetooth remote SIM Access Profile on vehicles with
Audi connect* and Audi phone box*.
142 ...
The MMI will generate a PIN for the connection
¢Fig. 140.
... Select and confirm Yes.
... Enter the PIN to establish a connection on your
mobile phone. Or: If the PIN is already being
displayed on your mobile phone, confirm it on
the phone and on the M MI. You have about 30
seconds to enter the PIN.
... If you wish to connect your mobile phone via
the remote SIM Access Profile, please also en­
ter your SIM card's PIN in the MMI 1
> .
... Please note any additional system queries on
your mobile phone, e.g. whether the phone
should connect automatically in the future. On
some mobile phones, you may also need to
download the directory and allow access to
your messages separately.
After connecting successfully
After the connection has been established suc­
cessfully, you will be shown a short message con­
taining information on the profiles used to estab­
lish the connection. You can also change the pro­
files afterwards. Select: !MENU! button
> Set­
tings > left control button> MMI settings > Con­
nection manager ¢page 215.
In addition, the contacts on the mobile phone are
automatically loaded into the directory of the
MMI. This may take several minutes, depending
on how many contacts are stored on the mobile
phone.
You can configure your vehicle's mobile Wi-Fi
hotspot 1
> and the Audi connect services*
¢page 159 immediately after connecting an
rSAP-enabled mobile phone. Or: Select !TEL! but­
ton > right control button> Connection manager
> right control button > Wi-Fi settings.
CD CAUTION
Please always observe the information ¢0 in
Wi-Fi hotspot on page 166. _______ �