2016 AUDI TT COUPE Owners Manual

Downloaded from www.Manualslib.com manuals search engine ..... N
a:
@ Tips
For additional information on ESC and ABS,
refer to ¢page 87.
BRAKE! .. (USA models) I rl] (Canada models)
Brake pads!
If the warning light turns on, immediately con­
tact your authorized Audi dealer or authorized
Audi Service Facility
to have all brake pads in­
spected . Both sets
of brake pads on an axle must
always be replaced at the same time.
A WARNING
Driving with bad brakes can cause a collision
and serious personal injury.
-
If the rl] warning light or the .. warning
light l) with the message Brake pads!
comes on in the instrument cluster display,
immediately contact your authorized Audi
dealer
or authorized Audi Service Facility to
have all brake pads checked or replaced if
necessary.
ffl;f !f Safety systems
-1
The II (USA models) Im (Canada models) indi­
cator
light monitors the safety systems.
Safety system
If the II (USA models) Im (Canada models) in­
dicator
light turns on or blinks, there is a mal­
function in a safety system.
Drive
to an authorized Audi dealer or authorized
Audi Service Facility immediately
to have the
malfunction corrected.
A WARNING
-Have the safety systems inspected immedi-
ately. Otherwise, there
is a risk that the sys­
tems may not activate during a collision,
which increases
the risk of serious injury or
death.
co ..... .....
:=: 1) - : USA models only
Instruments and indicator lights
~ Engine control
If the II indicator light turns on if there is a mal­
function in
the engine control.
Drive slowly
to an authorized Audi dealer or au­
thorized Audi Service Facility
to have the engine
checked .
o System indicator light (MIL)
The system indicator light (MIL) is part of the On
Board Diagnostic system (OBD II). The ¢.j sym­
bol turns on when the ignition is switched on and
turns
off again once the engine is started and
running
at a steady idle speed. This indicates that
the MIL is functioning correctly.
The indicator
light turns on if there is a malfunc­
tion in the engine electronics. See an authorized
Audi dealer or authorized Audi Service Facility
to
have the malfunction corrected.
For additional
information, refer to¢ page 17.
!?\Engine speed limitation
Applies to vehicles wit h en gi ne speed lim itation
(I! Maximum engine speed: XXXX rpm
The engine speed is automatically limited to the
speed displayed in the driver information system.
This protects
the engine from overheating.
The engine speed
limitation deactivates once the
engine is no longer in the critical temperature
range and you have released the accelerator ped­
al once.
If the engine speed limitation was activated by
an engine
control malfunction, the II indicator
light also turns on. Make sure the engine speed
does
not go above the speed displayed, for exam­
ple when downshifting. Drive
to an authorized
Audi dealer or authori z
ed Audi Service Facility im­
mediately to have the malfunction corrected.
~ Engine oil level (min.)
II Please check oil level
15

Downloaded from www.Manualslib.com manuals search engine Instruments and indicator lights
You may continue driving for the time being.
Check the engine oil level as soon as possible
<:!)page 239.
-If the engine oil level is too low, add engine o il
<:!)page 240.
-If the engine oil level is correct and the indica­
tor light still turns on, drive at low engine
speed to an authorized Audi dealer or author­
ized Audi Service Facility.
X;:';,,, Engine oil sensor
• Oil le vel system: malfunction! Please con·
tact Service
The sensor to check the engine oil level has
failed. Drive to an authorized Audi deale r or a u­
thorized Audi Service Facility immediately to have
the malfunction corrected.
[JlJ Tank system
D Ple a se r efuel
If the indicator light turns on for the first time
and the message appears, there are about 1.9
gal (7 L) of fuel left in the tank.
D Plea se refuel immediately
If t he indicator lig ht turns on the message ap­
pears, the fuel tank is almost empty. Refuel the
vehicle immediately.
D Tank sy ste m : malfun ction! Please contact
Servic e
If the indicator light t urns on and this message
appears, there is a malfunction in the tank sys­
tem.
Drive to an author ized Audi dealer or authorized
Audi Serv ice Facility immediately to have th e
malfunction corrected.
@l For the sake of the environment
Fuel should never enter the sewer system or
come into contact w ith the ground.
(Di Tips
More information on refueling is available on
page¢ page 232.
16
· ,_Washer fluid level
m Pleas e add washer fluid
Fill the washer fluid for the windshield washer
system and the headlight washer system* when
the ignit ion is switched off<:!) page 248.
\9 ! Windshield wipers
@Windshield wiper s: malfunction! Plea se
conta ct Servi ce
There is a malfunction with the windshield wip­
e r
s.
Drive to an authorized Audi dealer or authorized
Audi Service Facility immediately to have the
malfunction corrected.
-:q>.-Bulb failure indicator
If the II indicator light turns on, a bulb has
failed. The message indica tes the location of the
bulb.
Replace
the bu lb immediately .
Vehicle lights: malfunction! Please contact
Service
There i s a malfunction in the headlights or the
light switch. Drive to an authorized Audi dealer or
authorized Aud i Serv ice Facility immediately to
have the malfunction corrected.
&. WARNING
-Light bulbs are under pressure and can ex·
plode when bulbs are replaced, whic h in­
creases the risk of injury.
-
With gas-discharge lamps* (xenon head­
lights), the high-vo ltage component must
be handled appropriately. Otherwise, there
is a risk of fatal injury.
~CD Headlight range control system
II Headlight range control: malfunction! See
owne
r's manual
There i s a mal f u nction in the headlight range
control system, which may cause glare for other
drive rs. .,..

Downloaded from www.Manualslib.com manuals search engine Drive to an authorized Audi dealer or authorized
Audi Service Facility immediately to have the
malfunction corrected.
~O Audi adaptive light
Applies to: vehicles with Audi adaptive light
rJJ Audi adaptive light: malfunction! See own­
er's manual
There is a malfunction in the adaptive lights. The
headlights still function.
Drive to an authorized Audi dealer or authorized
Audi Service Facility immediately to have the
malfunction corrected.
li,D Light/rain sensor
El Automatic headlights: malfunction! See
owner's manual
II Automatic wipers: malfunction! See owner's
manual
The light/rain sensor is malfunctioning.
The low
beams remain switched on at all times
for safety reasons when the light switch is in the
AUTO position. You can continue to turn the
lights on and off using the light switch. You can
still control all wiper functions that are inde­
pendent of the rain sensor.
Drive to an authorized Audi dealer or authorized
Audi Service Facility immediately to have the
malfunction corrected.
; Damper control
App lies to: vehicles with Audi drive select
R Suspension: malfunction! You may continue
driving
There is an adaptive damper malfunction.
Drive to an authorized Audi dealer or authorized
Audi Service Facility immediately to have the
malfunction corrected.
Instruments and indicator lights
¢ Q Turn signals
If the. or B indicator light blinks, a turn sig­
nal is turned on. If both indicator lights are blink­
ing,
the emergency flashers are on.
In
an indicator light blinks twice as fast as usual,
then a turn signal bulb has failed. Replace the
bulb immediately.
CJ! 4f. Rear safety belt
Applies to: vehicles with rear safety belt detection
The respective indicator light will turn on briefly
when a safety belt on the rear seats is fastened
or unfastened.
f!l-If this indicator light turns on briefly, the
safety belt on the rear seat is not fastened.
II-If this indicator light turns on briefly, the
safety belt on the rear seat was fastened.
·-If this indicator light blinks, the safety belt
was unfastened while driving. Above a certain
speed, there will also be a warning tone.
(D Tips
For additional information on safety belts, re­
fer to ~page 180.
On-Board Diagnostic
system (OBD)
System indicator light (MIL)
The system indicator light (MIL) Ill in the instru­
ment cluster is part of the On Board Diagnostic
System (OBD II).
The
warning/indicator light turns on when the ig­
nition is
switched on and turns off once the en­
gine is started and is running in idle at a stable
speed. This indicates that the MIL is functioning
correctly.
If the light does not turn off after starting the
engine or turns on while driving, this may indi­
cate there is a malfunction in the engine. If the
indicator turns on, the catalytic converter may be
damaged. ..,.
17

Downloaded from www.Manualslib.com manuals search engine Instruments and indicator lights
Drive with reduced engine performance (avoid
high
speeds for extended periods of time and/ or
fast acceleration) and have the malfunction cor­
rected. See an authorized Audi dealer or author­
ized Audi Service Facility.
The
indicator may turn on if the electronic speed
lim iter is faulty. For additional information, refer
to c:> page 72, Electronic speed limiter.
On-Board Diagnostics
Fig. 4 Locat ion of Data Link Connector (DLC)
On-Board Diagnostics monitors the components
of your emission control system. Each monitored
component in your engine system has been as­
signed a code. In case of a malfunction, the com-
18
ponent will be identified and the fault stored as a
code in the control module memory.
The MIL light may also illum inate if there is a
l
eak in the on-boar d fuel vapor recovery system.
If the light illuminates after a refuelling, stop
the vehicle and make sure the fuel filler cap is
properly closed c:> page 233.
In order to make an accurate diagnosis, the stor­
ed data can only be displayed using special d iag­
nostic equipment (generic scan tool for OBD).
In order to connect the special diagnostic equip­
ment, push the plug into the Data Link Connector
(DLC). The DLC is located to the right of the hood
release c:> fig. 4.
Your authorized Audi dealer or a qualified service
station can interpret the code and perform the
necessary repair.
11. WARNING
Do not use the diagnostic connector for per­
sonal use. Incorrect usage can cause malfunc­
tions, which can increase the risk of a colli­
sion!
- I

Downloaded from www.Manualslib.com manuals search engine ..... N
G: CX)
.....
"' U"I
.....
"' .....
Driver information system
Overview
Fig. S Driver information system diagram: classic view
Fig. 6 Dri
ver in formation system diagram : expanded view
The driver information system displays various
items:
(!) Tachometer
@ Left additional display (divided in two sec-
tions in
the expanded view)
@ Tab area
@ Central area
® Status line (displayed on one or two lines)
@ Right additional display (divided in two sec-
tions in the expanded view)
A WARNING
Do not assume the roads are free of ice based
on
the outside temperature display. Be aware
Driver information system
that there may be ice on roads even when the
outside temperature is around 41 °F (+ S 0()
and that ice can increase the risk of accidents.
(0 Tips
-You can select the units used for tempera­
ture, speed and other measurements in
the
Infotainment system.
-
If your vehicle is stationary or if you are driv­
ing
at very low speeds, the temperature dis­
played may
be slightly higherthan the ac­
tual temperature outside due to the heat ra­
diating
from the engine .
-
At temperatures below 41 °F (+S 0(), a
snowflake symbol appears in
front of the
temperature display~.&.
19

Downloaded from www.Manualslib.com manuals search engine Driver information system
Multifunction steering
wheel plus
Operating
Apples to: vehicles with multifunction steering wheel plus
The Multifunction steering wheel plus* hos 14
buttons. You con use them to operate the driver
information
system and the MMI functions,
change the volume and switch the voice recogni­
tion system* on and off.
Fig. 7 Infotainment system display
Fig. 8 Multifunction
steering wheel operation
Requ irement: the ignition must be switched on.
The driver information
system contains multiple
tabs CD that display various information @.
The
following tabs are available, depend ing on
vehicle
equipment:
1. Tab Vehicle
2 . Ta
ba)
Warnings
3. Tab
Rad io¢ page 145
Media~ page 149
4. Tab Telephone* ¢page 110
20
5. Tab Navigation*¢ page 131
Map*
6. Tabb >
Sound ¢page 166
Audi connect* ¢page 121
Settings ¢page 166
a) This tab is only visible if at least o ne indicator light or
message is shown or if the correspon ding system is
sw i
tched on.
bl The contents of the tab depen d on the men u that was
used last.
® button I <11> I
- Switching tabs: press the I I button to the
left/right (for example, radio).
@IVIEWI button
-Switching views: press the IVIEWI button to
switch from the classic¢ page 19, fig. 5 to the
expanded ¢ page 19, fig. 6 view.
® buttonl2J
-Returning to functions at higher levels: press
the~ button.
@ 12] and 0 control buttons
-Opening the selection menu: press the left
control button.
-Opening the options menu: press the right
control button.
Q) Left thumbwheel
-Selecting a function in a menu/list: turn the
left thumbwheel to the desired function in a
menu or list (such as selecting a station, Lap
times*) .
-
Confirming a selection: press the left thumb­
wheel (for example, confirm the station).
-Zooming in/out on the map: when a map is
displayed, turn the left thumbwheel up/down
to zoom in/out on the map.

Downloaded from www.Manualslib.com manuals search engine ..... N
G: CX)
.....
"' U"I
.....
"' .....
Control buttons
Applies to: vehicles with multifu nction steering wheel plus
F ig . 9
Open ing th e selectio n and optio ns menu
Left control button
- Opening the selection menu : press the left
co ntrol bu tton Ill~ fig. 9. You can now select
and co nfirm a fu nction in the selection menu
using th e left thumbwheel (for ex ample, se­
lecting a frequency band) .
Right control button
-Opening the options menu: press the right
co ntrol bu tton (g ~fig. 9. You ca n now adjust
any context-dependent functions and settings
u sing th e left thumbwheel (for ex ample, sou nd
settings).
Driver information system
Preset buttons
Applies to: vehicles with multifunction steering wheel plus
Fig. 10 Multifun ctio n steering wheel, rig ht s ide
CD button !:a
-Accepting a call : when there is an incoming
call,
press the 0 button.
- Ending a call : press the 0 button during an ac­
tive
phone call.
- Opening the call list: if no phone call is in prog­
ress and there are no incoming calls, press the
0 button.
@button5l
-Switching the voice recognition system on:
briefly press the EE! button. Say the desired
command after the Beep.
- Switching
the voice recognition system off:
hold down the EE! button. Or: say the command
Cancel.
For more info rm ation about the voice recogni tion
system, refe r to ~page 104, Voice recognition
system.
®Right thumbwheel
You can adjus t the volume of an audio source or a
system message (for ex am ple, from the voice
recognition
system) when t he sou nd is playin g.
-Increasing or decreasing the volume : turn the
righ t thumbwheel upward or d ownward .
- Muting or pausing : turn th e right thumbwheel
downw ard .
Or: press the righ t thumbwheel.
-Unmuting or resuming : turn the right thumb­
wheel upwa rd. Or: p ress th e righ t thumbwheel. .,..
21

Downloaded from www.Manualslib.com manuals search engine Driver information system
©button l1<1<1l l1>1>1I
- Selecting the previous/next track or station :
press the ll1>1I butto n .
- Fast forwarding/rewinding audio files: press
and ho ld the li1>1 I b utton un til th e desired
loca tion
in the file is reached.
@button0
-Programmable steering wheel button -open­
ing a function : press the@ button on th e mul­
ti fu nct i
on steering wheel.
- Programmable steering wheel button -re­
questing a function : hold dow n the@button.
- Programmable steering wheel button -chang­
ing a function : select the first tab >Vehicle
settings > Steering wheel button assignment .
® button l~·"I
-Repeating the last voice guidance : press th e
l~""I button w hen route guidance is active .
-Changing the voice guidance volume: when
route guidance is active, turn the right thumb­
wheel upward or dow nward during voice guid­
ance.
Multifunction steering
wheel
Operating
The multifunction steering wheel has four but­
tons. With this feature , you can operate the driv­
er information system and the M MI functions
and you can also change the volume .
Fig . 11 Standard multifu nction steering wheel
Requirement: the ign ition must be switched on.
22
@Operating the driver information system
The driver information system contains multiple
tabs(!) t h a t display various information@ .
The following t
abs are availab le, depending on
vehicle equipment:
1. Tab Vehicle
2. Taba )
W
arnings
3. Tab Radio 9page 145
Media ¢page 149
4. Tabb )
Sound ¢page 166
Settings r=.>page 166
a) This tab is only v is ible if at least o ne indicator ligh t or
message is show n or if th e c orresponding sys te m is
sw i
tched on.
b ) The co ntents of th e t ab depe nd on th e men u t hat was
u sed l
ast.
-IMODEI: press the I MODEi button until the de­
sired tab is displayed.
- Tur ning
the left thumbwheel: turn the le ft
thumbwheel to the desired f unctio n.
-
Pressi ng the left t humbwh eel: press th e left
thumbwheel to confirm your selection.
- Q uick ly turning t he left thumbwheel: quickly
t u rn
the left thumbwheel to scroll in the list.
@ IVIEWI button
-Switching views: press the IVIEWI button to
sw itch from the cla ssic 9 page 19, fig. 5 to the
expanded 9 page 1 9, fig. 6 view .
@Right thumbwheel
The volume of an audi o source or a system mes­
sage (such as traffic announcements) can be di­
rectly adjusted during th e audio outpu t.
- Increasing or decreasing the volume : turn the
right thumbwheel upward or downwa rd .
- Muting or pausing: turn the right thumbwheel
downward. Or : press the right thum bwheel.
-Unmuting or resuming : turn the right thumb­
wheel upward. Or: press the right thumbwh eel.