2016 AUDI TT COUPE oil

Downloaded from www.Manualslib.com manuals search engine Instruments and indicator lights
You may continue driving for the time being.
Check the engine oil level as soon as possible
<:!)page 239.
-If the engine oil level is too low, add engine o il
<:!)page 240.
-If the engine oil level is correct and the indica­
tor light still turns on, drive at low engine
speed to an authorized Audi dealer or author­
ized Audi Service Facility.
X;:';,,, Engine oil sensor
• Oil le vel system: malfunction! Please con·
tact Service
The sensor to check the engine oil level has
failed. Drive to an authorized Audi deale r or a u­
thorized Audi Service Facility immediately to have
the malfunction corrected.
[JlJ Tank system
D Ple a se r efuel
If the indicator light turns on for the first time
and the message appears, there are about 1.9
gal (7 L) of fuel left in the tank.
D Plea se refuel immediately
If t he indicator lig ht turns on the message ap­
pears, the fuel tank is almost empty. Refuel the
vehicle immediately.
D Tank sy ste m : malfun ction! Please contact
Servic e
If the indicator light t urns on and this message
appears, there is a malfunction in the tank sys­
tem.
Drive to an author ized Audi dealer or authorized
Audi Serv ice Facility immediately to have th e
malfunction corrected.
@l For the sake of the environment
Fuel should never enter the sewer system or
come into contact w ith the ground.
(Di Tips
More information on refueling is available on
page¢ page 232.
16
· ,_Washer fluid level
m Pleas e add washer fluid
Fill the washer fluid for the windshield washer
system and the headlight washer system* when
the ignit ion is switched off<:!) page 248.
\9 ! Windshield wipers
@Windshield wiper s: malfunction! Plea se
conta ct Servi ce
There is a malfunction with the windshield wip­
e r
s.
Drive to an authorized Audi dealer or authorized
Audi Service Facility immediately to have the
malfunction corrected.
-:q>.-Bulb failure indicator
If the II indicator light turns on, a bulb has
failed. The message indica tes the location of the
bulb.
Replace
the bu lb immediately .
Vehicle lights: malfunction! Please contact
Service
There i s a malfunction in the headlights or the
light switch. Drive to an authorized Audi dealer or
authorized Aud i Serv ice Facility immediately to
have the malfunction corrected.
&. WARNING
-Light bulbs are under pressure and can ex·
plode when bulbs are replaced, whic h in­
creases the risk of injury.
-
With gas-discharge lamps* (xenon head­
lights), the high-vo ltage component must
be handled appropriately. Otherwise, there
is a risk of fatal injury.
~CD Headlight range control system
II Headlight range control: malfunction! See
owne
r's manual
There i s a mal f u nction in the headlight range
control system, which may cause glare for other
drive rs. .,..

Downloaded from www.Manualslib.com manuals search engine Driving
Driving
General information
New engine
The engine needs to be run-in during the first
1,000 mi (1,500 km).
For the first 600 mi (1,000 km):
... Do not use full throttle.
... Do not drive at engine speeds that are more
than 2/3 of the maximum permitted RPM.
... Avoid high engine speeds.
From 600 to 1,000 mi (1 ,000 to 1,500 km):
... Speeds can gradually be increased to the maxi­
mum permissible road or engine speed.
During and after break-in period
... Do not rev th e engine u p to high speeds when it
is cold. This
applies whether the transmission is
in N
(Neutral) or in gear.
After the break-in period
... Do not exceed maximum engine speed under
any cir cu
mstances .
... Upshift into th e nex t higher gear before reach ­
ing th e red
area at th e end of the tachometer
sea le r=:> page 8 .
During the firs t few hours of drivi ng, the engine's
interna l fric tion is higher than later when a ll th e
moving parts have been broken in . How well this
break-in process is done depends to a considera­
ble extent on the way the vehicle is driven during
the first 1,000 mi (1,500 km).
@Note
Extremely high engine speeds are automati­
cally reduced. However, these rpm limits are
programmed for an engine well r un -in, not a
new engine.
@ For the sake of the environment
Do not drive with unnecessarily high engine
speeds -upshi fting early saves fuel, reduces
noise and protects the environment.
56
·New tires
If your veh icle is runni ng on new tires, d rive par­
t icula rly careful for the first 350 m i (500 km) af­
ter fitting.
.&. WARNING
-New tires tend to be slippery and must a lso
be "broken-in". Be sure to remember this dur­
ing the first 350 m i (500 km). Brake gently .
Avoid following closely behind other vehicles
or other situations that might req uire sudden,
hard braking.
Avoid damaging the vehicle
When you are driv ing on poor roads, or over
cu r
bs, steep ramps, etc., make certain that l ow­
l y i
ng parts such as sp oile rs and exhaust system
parts do not bottom out and get damaged.
This is especially true for veh icles with low-s lu ng
c h
assis (sports chassis) * and fully loaded
vehicles .
Driving through water on roads
Note th e following to avo id vehicl e damage when
driv ing thro ugh water, for example on flooded
roads:
- The wat
er must not be any higher than the bot­
t
om of the vehicle body.
-
Do not dri ve faster than walking speed.
_&. WARNING
Af te r driving through water or mu d, the brak­
ing e
ffect can be reduced due to moisture on
the brake d iscs and brake pads. A few careful
b rake applications should dry off the bra kes.
@Note
Vehicle components such as the engi ne,
transmission, su s pension o r electrica l system
can be severely damaged by driving through
water. ..,.

Downloaded from www.Manualslib.com manuals search engine @ Tips
-Determine the depth before driving through
water.
-Do not stop the vehicle, drive in reverse or
switch the engine off when driving through
water.
- Keep in mind that oncoming vehicles may
create waves that raise the water level and
make it too deep for your vehicle to drive
through safely.
- Avoid driving
through salt water (corrosion).
Economical and environmentally-friendly
driving
The amount of fuel consumption, the envi ron­
mental impact and the wear to the engine,
b rakes and tires depends mostly on yo ur driving
style. Wit h
an anticipatory and economic driv ing
style, fu
el consumption can be reduced by ap­
proximately 10-lSo/o. The following tips will help
you conserve the environment and your money at
the same time.
Anticip atory driv ing
A veh icle uses the most fuel when a ccele rating.
When you drive with anticipation, you do not
need to brake as often and thus acce lerate less.
When possible, let your vehicle coast with a gea r
engaged -for example, when you notice that the
next traffic light is red.
Avoid full acceleration
You should rarely travel at the maximum vehicle
speed. High speeds cause a disproportionately
high increase in fuel consumption, emissions and
traffic noise. Slower driving saves fuel.
Reduce idling time
It pays off to stop the engine, for example when
at railroad crossings or traffic lights with longer
red lights. Stopping the engine for 30-40 sec­
onds already saves more fuel than the amount of
extra fuel needed to restart the engine.
It takes a very long time in idle to warm the en­
gine up to operating temperature. Wear and
emissions are especially high in the warm-up
Driving
phase. Therefore, you should begin driving im­
mediately after starting the engine. Avoid high
RPMs while doing this.
Service regularly
By servic ing you r vehicle regularly, you can help
to reduce fuel consumption before you even start
to drive . The maintenance condition of your vehi­
cle not only affects traffic safety and long-term
val ue b ut also impacts fuel co nsumptio n.
A poorly serviced engine can lead to fuel con­
sumption that is 10% higher than normal.
Also check the oil level when refueling. The oil
con sumpti on
depends largely on the engine load
and speed. It is no rmal for the oil consumption
of a new engine to reach its lowest point only af­
ter a certain amount of use. Therefore, the oil
consumption can only be properly judged after
approximately 3,000 mi (5,000 km) have been
driven.
Avoi d short trip s
The engine and exhaust cleaning system must
reach their optimal operating tempera tu re to ef­
fectively reduce consumption and emissions.
A cold engine consumes a disproportionately
high
amount of f u el. The engine is at operating
temperature and consumption has normalized
only after approximately four kilometers.
Q) Note
Do not leave engine idling unattended after
starting. If warning lights should come on to
indicate improper operation, they would go
unheeded. Extended idling also produces
heat, which could result in overheating or
other damage to the vehicle or other proper­
ty.
CD Note
-Have your vehicle maintained properly and
in accordance with the service recommenda­
tions in your Warranty & M ain tenance book-
let. Lac k of proper mai ntenance as well as
improper use of th e vehi cle w il l impair the
function of the emission control system and
cou ld lead to damage. .,..
57

Downloaded from www.Manualslib.com manuals search engine ...... N
> u. CX> ...... u:>
"' ...... u:> ......
-There is no vehicle stabilization when ESC/
ASR are switched off.
(D Tips
-When the cruise control system is switched
on, ESC/ ASR cannot be switched off or sport
mode cannot
be switched on.
- Malfunctions in the rear spoiler
or the Audi
magnetic ride may make
it impossible to
switch the ESC/ ASR off or to switch sport
mode on.
Brakes
New brake pads
New brake pads do not achieve their full braking
effect during the first 250 mi (400 km) . They
must be "broken in" first. However, you can com­
pensate
for the slightly reduced braking force by
pressing
firmly on the brake pedal. Avoid heavy
braking during the break-in period.
Wear
Brake pad wear depends largely on the way the
vehicle is driven and on operating conditions.
This is especially true
if you are driving frequently
in
the city and on curves or with a sporty driving
style.
Operating noise
Noises may occur when braking depending on the
speed, braking force and outside conditions such
as temperature and humidity.
Effect of water and road salt
In certain situations, for example after driving
through water, in heavy
rain, after overnight con­
densation
or after washing your car, the braking
effect can be reduced by moisture or ice on the
brake rotors and brake pads. The brakes
must be
"dried" first with a few careful brake applica­
tions.
At higher speeds and with the windshield wipers
turned
on, the brake pads press against the brake
rotors
for a short amount of time. This action
which is
not felt by the driver happens at regular
Intelligent Technology
intervals and facilitates a better reaction time for
the brakes in wet weather.
T
he braking effect can also be reduced if you are
driving on salted roads and you do
not apply the
brakes for Long periods of time. The Layer of salt
on the brake rotors and pads must be worn off
first when the brakes are applied.
Corrosion
Leaving the vehicle parked for Long periods of
time, Low mileage and avoiding heavy braking
can contribute
to corrosion on the brake rotors
and
dirty brake pads.
If you usually avoid heavy braking or ifthere is
corrosion present, occasiona l heavy braking
at
high speeds is recommended to clean the brake
rotors and
pads¢.&..
Brake system malfunction
if you notice that the brake pedal travel has sud­
denly gotten Larger, then a brake circuit may have
failed. Drive
to an authorized Audi dealer or au­
thorized Audi Service Facility immediately to have
the problem corrected. On the way there, drive
with reduced speed and keep in mind that a Long
braking distance and increased pressure on the
brake pedal will be necessary.
Low brake fluid level
When the brake fluid Level is Low, malfunctions in
the brake system may occur. The brake fluid Level
is electronically monitored.
Brake booster
The brake booster amplifies the pressure you ap­
ply to the brake pedal. It only works when the en­
gine is running.
A WARNING
-New brake pads do not achieve their full
braking effect during the first 250 mi
(400 km). They must be "broken in" first.
However, you
can compensate for the
slightly reduced braking force by pressing
firmly on the brake pedal. Avoid heavy brak-
ing during
the break-in period. ~
89

Downloaded from www.Manualslib.com manuals search engine Intelligent Technology
-Only apply the brakes for the purpose of
cleaning the brake system when road and
traffic conditions permit. You must not en­
danger other road users. This increases the
risk of an accident.
-
On steep slopes, reduce the speed and se­
lect a lower gear or lower selector lever po­
sition . Drive
as little as possible while press­
ing the brake pedal and avoid putting your
left foot on the brake pedal while driving.
This could
cause the brakes to overheat and
impair the efficiency of the brakes.
-
Do not let the brakes "grind" by always
keeping
your foot on the brake pedal. This
can
cause the brakes to over heat, increase
wear and increase brak ing distance u nneces ­
sari ly.
-
Certa in weather and operating cond it io ns
such as driving through water, driving in
heavy rain or driving after washing your ve­
hicle
can impair the effectiveness of the
brakes. In the winter, ice may build up on
the brake pads, rotors and drums. Check
these components by braking carefully. Ap­
plying
the brakes carefully several times
dries the brakes and removes ice build-up.
- The efficiency
of the brakes can also be im­
paired by driving
for long stretches on roads
covered with salt without using the brakes.
You can remove salt deposits from the
brake rotors and pads by carefully applying
the brakes several times.
-If the front spoiler is damaged or you install
another spoiler, make sure the front wheel
brakes are ventilated properly. Otherwise,
the brake system could overheat, wh ic h re ­
duces
thei r effectiveness.
- Failure
of a brake circuit impairs braking
performance, which increases braking dis­
tance.
Avoid driving the vehicle and have it
towed it to the nearest authorized Audi
dealer or authorized Audi Service Facility.
- Never
let the vehicle roll while the engine is
stopped because this increases the risk of an
accident.
-
If the brake booster is not working, you will
have
to press much harder on the brake
90
pedal to compensate for the lack of the
booster.
@ Note
-Never let the brakes "rub" by pressing the
pedal lightly when braking is not really nec­
essary. This
causes the brakes to overheat
and increases braking distance and causes
wear.
- Before driving a long
distance on a steep
slope, decrease your speed and select a low­
er driving gear. This makes use of the en­
gine braking effect and relieves the brakes.
If you need to brake additionally, brake in
interva ls and not continuously.
(D Tips
-Ifthe brake booster is not work ing, you
must press the brake pedal w ith much more
force than normal.
-
If you retrofit your vehicle with a front spoil­
er wheel covers or similar items, make sure '
that the air flow to the front wheels is not
interrupted. Otherwise the brake system
can become too hot.
Electromechanical
steering
The electromechanical steering supports the
driver's steering movements.
Power steering adapts electronically based on
the vehicle speed.
Indicator lights and messages
• Steering: malfunction! Please stop vehicle
If this indicator light turns on and stays on and
this message appears, the power steering may
have failed.
Stop the vehicle in a safe location as soon as pos­
sible.
Do not continue driving. See an authorized
Audi dealer or authorized Audi Service Facility for
assistance.
i:t-D Steering: malfunction! You may continue
driving

Downloaded from www.Manualslib.com manuals search engine ..... N
G: CX)
.....
"' U"I
.....
"' .....
If the indicator light turns on, the steering wheel
may be more difficult to move or more sensitive
than usual. The steering wheel may also be at an
angle when driving straight.
Drive slow ly to an authorized Audi dealer or au­
thorized Audi Service Facility to have the mal­
function corrected.
@ Tips
If the. or '~ij indicator light only stays on
for a short time, you may continue driving.
ALL wheel drive (quattro)
In all wheel drive, all four wheels ore powered.
General information
In all wheel drive, the driving power is divided be­
tween all four wheels. This happens automatical­
ly depending on your driving behavior as well as
the current road conditions. c::> page 87, Electron­
ic
stabilization control (ESC).
The all wheel drive concept is designed for high
engine power. Your vehicle is exceptionally pow­
erful and has excellent driving characteristics
both under normal driving conditions and on
snow and ice. Always read and follow safety pre­
cautions c::> &..
Winter tires
By using all wheel drive, your vehicle has good
forward motion with standard tires in winter con­
ditions. However,
in winter we recommend using
winter or all season tires on all four wheels, be­
cause this will improve the broking effect.
Snow chains
If there are snow chain laws, snow chains must
also be used on vehicles with all wheel drive
c::> page 265, Snow chains.
Replacing tires
For vehicles with all wheel drive, only wheels with
the same rolling circumference should be used.
Avoid
wheels with different tread depths
c::> page 257, New tires or wheels.
Intelligent Technology
Offroad vehicle?
Your Audi is not an offroad vehicle -there is not
enough ground clearance. For this reason, avoid
difficult
terrain.
&,,!!_ARNING
-I
-Also, in vehicles with all wheel drive, adapt
your driving style to the current road and
traffic conditions. Do not let the increased
safety provided tempt you into taking risks,
because this increases the risk of an acc i­
dent.
- The braking ability
of your vehicle is limited
to the traction of the wheels. In this way, it
is not different from a two wheel drive vehi­
cle.
Do not be tempted to accelerate to a
h
igh speed when the road is slippery this in­
creases the risk of an accident.
- Note
that on wet streets, the front wheels
can "hydrop lane" if driving at speeds that
are too high. Unlike front wheel drive
veh icl
es, the engine does not rev higher sud­
denly when the vehicle begins hydroplaning .
For
this reason, pay attention to the road
conditions
regard less of your speed.
Rear spoiler
The extendoble rear spoiler increases driving sta­
bility.
Fig. 89 Center console: button for the rear spoiler
The rear spoiler retracts and extends. It can be
activated in various operating modes (manual
mode or automatic mode) .
91

Downloaded from www.Manualslib.com manuals search engine Intelligent Technology
Automatic mode (normal operation)
-Automatic extension: the rear spoiler will auto­
matically extend when speeds exceed approxi­
mately 75 mph (120 km/h)
-Automatic retraction: the rear spoiler will auto­
matically retract when speeds decrease to un­
der approximately 50 mph (80 km/h).
Manual mode
-Extending manually: briefly tap the~ fig. 89
button to fully extend the rear spoiler.
- Retracting manually:
when driving at speeds
below approximately 10 mph (20 km/h), press
and hold the button to retract the rear spoiler.
When at speeds between 10 mph (20 km/h)
and 75 mph (120 km/h), the rear spoiler will
completely retract when you tap the button.
Indicator lights
Ii) I. Rear spoiler: malfunction!
The
rear spoiler may not have extended due to a
malfunction.
This could change the veh icle's driv­
ing characteristics
at high speeds. Do not drive
faster than 85 mph (140 km/h). Drive to an au ­
thorized Audi dealer or authorized Audi Service
Facility
immediately to have the malfunction cor­
rected. The color
of the indicator light depends
on the vehicle speed.
..&. WARNING
-
Driving at higher speeds without the rear
spoiler deployed can impair handling charac­
teristics, making
the vehicle harder to con­
trol.
- Always
make sure that the spoiler is de­
ployed when driving at
speeds ove r 85 mph
(140 km/h). If the rear spoiler warning/indi­
cator light in the instrument cluster comes
on, the rear spoiler may not have deployed.
- Never drive
at speeds higher than 85 mph
(140 km/h) ifthe spoiler is not deployed.
Have
the spoiler inspected as soon as possi ­
ble by an
authorized Audi dealer or qualified
workshop.
- Always obey
speed limits and other traffic
laws.
92
..&. WARNING
Improper operation of the rear spoiler can
cause crushing injuries.
-Always make sure that nobody, especially
children, is
in the way when the rear spoiler
is deployed or retracted.
«J:) Note
-Never push on the vehicle on the rear spoil­
er. This could
cause damage.
- To
prevent damage to the rear spoiler do
not lean or place anything on it.
-
-Only operate the rear spoiler manually when
the luggage compartment lid is close and
the rear spoiler moving parts are not
blocked. Otherwise, damage could occur.
(D Tips
Clean the rear spoiler compartment every 2 to
3 months. To function correctly, the rear
spoiler must be free of ice, snow and leaves.
Energy management
The starting ability is optimized
The energy management system manages the
electrical energy distribution
and optimizes the
availability
of electrical energy for starting the
engine.
When a vehicle with a conventiona l energy sys­
tem is not driven for a long time, the battery is
drained by equipment (for example the immobil­
izer). In
certain circumstances, there could may
not be enough energy to start the engine.
Your vehicle
is equipped with an intelligent ener­
gy
management system for distributing electrici­
ty. T his sign ificant
ly improves the starting ability
and increases the battery life.
The
energy management system Is made up of
battery diagnosis, Idling current management
and dynamic energy management.
Battery diagnosis
The battery diagnosis determines the battery
charge level. The sensors determine the battery Ill>

Downloaded from www.Manualslib.com manuals search engine ..... N
G: CX)
.....
"' U"I
.....
"' .....
.. Guide the reserve canister filler tube into the
funnel and start the emergency fueling.
.. Remove the funnel after refueling and close the
fuel filler door so that it latches shut.
CD Note
Remove any overflowing fuel from the ve hicle
paint immediately.
Fuel filler door emergency release
If the fuel filler door lock is faulty, the fuel filler
door con be unlocked manually.
Fig. 181 L uggage compa rtment: cover in t he r ight side
t
rim panel
.,.. Open the luggage compartment lid.
.. L ift the cargo floor .
"'
"' 0 0
it IIl
.,.. Loosen the strap from its holde r and pull on it
carefu lly Qfig. 181.
Catalytic converter
It is very important that your emission control
system (catalytic converter) is functioning prop­
erly to ensure
that your vehicle is running in on
environmentally sound manner.
.,.. Always use lead-free gasoline Q page 231, Gas­
oline grade .
.. Never run the tank down all the way to empty.
.. Never put too m uch motor oil in your engine
Q page 240, Adding engine oil "t::r..
.. Never try to push-or tow-start your vehicle.
The
catal ytic converter is an efficient "clean-up"
device built into the exhaust system of the vehi­
cle. The catalytic
converter burns many of the
pollutants in the exhaust gas before they are re­
leased into
the atmosphere .
Checking and Filling
The exclusive use of unleaded fuel is critically im­
portant for the life of the catalytic converter and
proper functioning of the engine.
A WARNING
f= - I
The temperature of the exhaust system is
high, both when driving and after stopping
the engine.
- Never
touch the exhaust tail pipes once they
have become hot. This could result in burns.
-Do not park or operate the vehicle in a reas
where the hot exhaust system may come in
contact with dry grass, brush, fuel spill or
other material which can cause a fire .
-
Do not appl y additional undercoating or
r ustproofing on or near the exhaust mani­
fold, exhau
st pipes, catalytic converter or
heat shields. During driving, the substance
used for un dercoating could overheat and
cause a fire.
CD Note
-Be aware that just one tank filli ng with
leaded fuel w ill already seriously degrade
the performance of th e c atalytic converter .
-
Do not exceed the correct engine oil leve l
Qpoge240 .
-Do not drive until the fuel tank becomes
completely empty. The engi ne could mis­
fire. Unbu r
ned fuel coul d also get into the
exhaust system and this could cause the
ca ta lyt ic co nver ter to overheat.
-Do not swi tch off the ignition whil e the vehi ­
cl e is moving .
-
Do not continue to operate your vehi cle un­
der these condi tions, as o therwise fuel c a n
reach the catalytic converter. This could re­
sult in over heating of the converter, requir­
ing
its replacement .
- T o assu re
effic ient operatio n of the E mis ­
sion Contro l System:
-Have your vehicle maintained properly and
in accordance wi th the service recommen­
dations in yo ur Warranty & Main tenance
bookle t.
- L ack
of proper maintenance as well as im-
p r
oper use of the veh icle w ill impair the .,..
235