2016 AUDI TT COUPE ignition

Downloaded from www.Manualslib.com manuals search engine ..... N
G: CX)
..... I.Cl U"I
..... I.Cl .....
Opening and closing
Central locking
Description
You can lock and unlock the veh icle centrally. You
have the following options:
-Remote control key<=> page 2 7,
-
Sensors in the door handles*<=> page 28,
- Lock cylinder on the driver's door<=> page 30,
or
-Central locking switch inside<=> page 29.
Auto Lock
The Auto Lock function locks all doors and the
luggage compartment lid once the speed has ex­
ceeded approximately 9 mph (lS km/h).
The vehicle can be unlocked if the opening func­
tion in the central locking system switch is used
or one of the door handles is pulled. The Auto
Lock function can be switched on and off in the
Infotainment system<=> page 29.
Additionally, in the event of a crash with airbag
deployment the doors are automatically un­
locked to allow access to the vehicle.
Selective unlocking
The doors and luggage compartment lid will lock
when they close. You can set in the Infotainment
system whether only the driver's door or the en­
tire vehicle should be unlocked when unlock ing
<=>page29.
Turn signals
When you unlock the vehicle, the turn signals
f l
ash twice. When you lock the vehicle, the turn
signals flash once. If the blinking continues, one
of the doors or the luggage compartment lid is
not closed or the ignition is sti ll switched on.
Unintentionally locking yourself out
In the following cases there safeguards to pre­
vent you locking your remote master key in the
vehicle:
-
If the driver's door is open, the veh icle cannot
be locked by pressing the !ml button on the re-
Opening and closing
mote control key or touching the locking sen­
sor* on a door.
-When locking using the Im] button in the central
locking switch, the vehicle will not lock if a door
is open <=>page 29.
-On veh icles with a convenience key*, the lug­
gage compartment lid unlocks again after clos­
ing if
the most recently used key is in the lug­
gage compartment. The emergency flashers
blink four times.
Do not lock your vehicle with the remote control
key or convenience key* until all doors and the
luggage compartment lid are closed. In this way
you avoid locking
yourself out accidentally.
@Tips
-Do not leave valuables unattended in the ve­
hicle. A locked vehicle is not a safe!
-The LED in the driver's door rail blinks when
you lock the vehicle. If the LED lights up for
approximately 30 seconds after locking,
there is a malfunction in the central locking
system. Have the problem corrected by an
authorized Audi dealer or authorized Audi
Service Facility.
Key set
Fig. 14 Your vehicle key set
@ Remote control key with integrated
mechanical key
You can unlock/lock your vehicle with the remote
control key . A mechanical key is integrated in the
remote control key ¢ page 26.
@ Key fob with PIN
Only applies to vehicles with Connectivity serv-
ice* :
open the key fob and rub the PIN until it is ..,.
25

Downloaded from www.Manualslib.com manuals search engine Opening and closing
visible . You can activate the Connectivity service*
on your vehicle using this PIN code.
Replacing a ke y
If a key is lost, see an authorized Audi dealer or
authorized Audi Service Facility. Have this key de­
activa ted. It is important to bri ng all keys wit h
you .
If a key is lost, you should report it to your
insurance company.
Numb er of keys
You can check the number of keys assigned to
your veh icle in the Infotainment system. To do
this, select: the I MENU I button > Vehi cle > left
control button > Service & checks > Vehicle in·
fo rma tion. This way, you can make sure that you
have
all the keys when purchasing a used vehicle.
Electron ic immobilizer
The immobilizer preven ts unauthorized use of
the vehicle.
Unde r certain circumstances, the vehicle may not
be able to start if there is a key from a different
veh icle manufacturer on the key chain.
Data in the master key
When driving, service and maintenance-relevant
data is continuously stored on your remote con­
trol key. Your Audi service advisor can read out
this data and tell you about the work your vehi cle
needs. This applies also to vehicles with a con­
ven i
ence key*.
Personal comfort settings
If two people use one vehicle , it is recommended
that each person always uses "their own " master
key. When the ignition is turned off or when the
veh icle is locked, personal convenience settings
for the following systems are stored and as­
signed to the remote master key.
-
Climate control system
-Parking aid*
- Active
lane assist*
- Si
de assist*
- Drive
select
26
The stored settings are automatically recalled
when you unlock the vehicle, open the doors or
turn on the ignition .
_&WARNING
Always take the vehicle key with you when
leav ing the vehicle, even for a short period of
time. This applies particularly when children
remai n in the vehicle . Otherwise the children
could
start the engine or operate e lectrical
equipment such as power w indows .
@Tips
-1
The operation of the remote control key can
be
temporarily d isrupted by interference from
transmitters in the vic in ity of the vehicle
working
in the same frequency range (e.g. a
cell
phone, rad io equipment). Always check if
your vehicle is locked!
Removing the mechanical key
Fig. 15 Remote contro l master key : remov ing the m ec ha ni·
cal key
.,,. Press the release buttons@<=> fig. 15 and re­
move the mechanical key from the remote con­
trol key.
Using the mechanical key, you can:
- Lock/ unlock th e g love
compartment.
- Man ually lock/unlock
the vehicle ¢ page 30.
-Emergency lock the doors c::> page 30.

Downloaded from www.Manualslib.com manuals search engine Opening and closing
Power windows
Controls
The driver can control all power windows.
Fig. 26 D river's door: powe r w in dow controls
All power window switches h ave a two- stage
function:
Opening the windows
"' Press t h e switch to the first level and hold it
until the window reaches the desired position .
"'To open the window completely, press the
swi tch all the way down to the second level
briefly .
Closing the windows
"'Pull the switch up to the first level and hold it
until the window reaches the desired position.
"'To close the window completely , pull the
switch u p to the second level briefly.
Power window switches
CD Left front door
@ Right front door
A WARNING
- Always take the vehicle key with you when
leaving the vehicle, even for a short period
of time. This applies particularly when chi l­
dren remai n in the vehicle. Otherwise the
children could start the engine or operate
electrical equipment (e .g . power windows).
T he
power windows are functional until the
driver's door or passenger's door has b een
o pened.
- Pay carefu l attention when closing the win­
dows. It could cause in jur y by pin ching .
32
N
N
M 0 ::) CX> ID
-1
-When locking the vehicle from o utside, the
veh icle must be unoccupied since the win­
dows can no longer be opened in an emer­
gency.
(l} Tips
-After turning the ignition off you can s till
open and close the windows for approxi­
mately 10 mi nutes. The power windows are
not switched off until the driver 's door or
passenger's door has been opened.
-When you open the doors, the windows au­
tomatically lower approximately 10 mm.
Convenience opening/closing
All windows can be opened and closed at the
same time.
Convenience open feature
"' Press the~ button on the remote contro l key
until all windows reach the desired position.
Convenience close feature
"' Press the ~ button on the remote control key
until all w indows are closed~ A or
Convenience closing with the convenience
key*
"'Touch the sensor * on the door handle long
enough until all w indows are close d. Do not
place your hand in the door handle when doing
this.
Setting convenience opening in the
Infotainment system
.. Select in the Infotainment system: IMENUI but­
ton > Vehicle > left control button >Vehicle set­
tings .
To enable the conven ience window opening f u nc ­
tion, the Long press to open windows function
must be switched on.
A WARNING
-Never close the windows ca relessly or in an
uncontrolled manner, because this increas­
es th e risk of injury.

Downloaded from www.Manualslib.com manuals search engine Opening and closing
Programming the transmitter
Applies to: vehicles with garage door opener (Homelink)
F ig.
29 Distance between the radiator grille and the re­
mote control transmitter
Programming the button : step 1 on the
control panel
1. Switch on the ign ition.
2.
Press both of the outside buttons on the con­
trol panel Q page 33, fig. 28 until the yellow
LED@ turns off and the green LED@ blinks.
This procedure clears
the standard codes that
were set at the factory and does not need to
be repeated again to program the other but­
tons.
3. Briefly press the button in the control panel
that you want to program.
4. Wait until the yellow LED@ blinks. The pro­
gramming mode is active for 5 minutes.
5.
Go in front of the vehicle with the original re­
mote control transmitter for the system that
you are programming to the control panel
button.
Programming the button : step 2 at the
radiator grille
6. Hold the remote control transmitter at the
vehicle radiator grille c:> fig. 29.
7 . Now press the remote control transmitter
until the turn signals on your vehicle blink.
This can
take up to 30 seconds.
8.
If the emergency flashers blink three times,
the programming was successful. If the
emergency flashers only blink one time, the
5 minute time limit for programming has ex­
pired
or the programming was unsuccessful.
Repeat the programming starting from the
third step or change the distance to the radi­
ator grille.
34
9. If the garage door or other systems do not
open with the Homelink buttons even if the
programming was successful, the system
may use a rolling code instead of a fixed
code.
You must also then perform rolling
co de
programmin g Q page 35.
The other two buttons in the control panel can be
programmed using the instructions given above.
Start with step 3.
Deleting button programming
The programmed buttons cannot be deleted indi­
vidually, they
must be deleted all at once. Repro­
gram the buttons if necessary.
... Sw itch on the ign ition.
... Press both of the outside buttons on the con­
trol unit until the yellow LED@ turns off and
the green LED@ blinks .
Reprogramming buttons
... Switch on the ignition .
... To reprogram an individual button, press the
desired button until the green LED@ turns off
and the yellow LED@ starts to blink (after ap­
proximately
20 seconds). Release the button
immediately. The programming mode is active
for S minutes.
... Continue with step 5.
(!) Tips
-The distance needed between the remote
control transmitter and the Homelink mod­
ule in the radiator grille c:> fig. 29 depends
on the system you are programming.
- Depending on the system model, you may
need
to release the button on the remote
control transmitter while it is programming
and press it again. Hold every position you
try when programming for at least 15 sec­
onds before trying a new position. Keep an
eye on the vehicle turn signals while doing
this.

Downloaded from www.Manualslib.com manuals search engine Lights and Vision
Lights and Vision
Exterior Lighting
Switching lights on and off
Fig. 30 Instrument panel: light switch
Light switch ·'t/;
Turn the switch to the corresponding position.
When
the lights are switched on, the :oo: symbol
turns on.
0 -lights are off (in some markets, the daytime
running
lights* are switched on when the ignition
is switched on.)
-USA models: the daytime running lights sw itch
on automatica
lly when the ignition is sw itched
on and
the light switch is set to the 0 or the
AUTO position (only in daylight). The Daytime
running lights
can be switched on and off in
the MMI ~page 37 Q &.
-Canada models: the daytime running lights
switch on automatically when the ignition is
switched on and the light switch is set to the 0,
:oo: or the AUTO position (only in daylight) QA .
AUTO* -automatic headlights switch on and off
depending on brightness, for example in twilight,
during rain
or in tunnels.
:oo: -Parking light
~D -Low beam headlight
~ -All weather lights*
All-weather lights*
In vehicles with all-weather lights, the front
lights are adjusted automatically so that you are
less likely
to see glare from your own headlights,
for example when driving on a wet road.
36
Automatic dynamic headlight range control
system*
Your vehicle is equipped with a headlight range
control system
so that the headlights do not
blind oncoming traffic if the vehicle load
changes. The headlight range also
adjusts auto­
matically when braking and accelerating .
Light functions
The following light functions are available de­
pending on vehicle equipment and only function
when the
light switch is in the AUTO position.
You can deactivate these functions in the Info­
tainment system under Audi adaptive light
Qpage 37.
Static cornering light* (vehicles with LED head­
lights) -the cornering light switches on automat­
ically when the steeri ng wheel is turned at acer­
tain angle at speeds up to approximately 44 mph
(70 km/h) and when the turn signal is activated
at speeds up to approxim ately 25 mph (40 km/
h). The area
to the side of the vehicle is illuminat­
ed better when turning.
Highway light function* (vehicles with LED head­
lights) -this function adapts the lighting for
highwa y driving based on vehicle speed.
Speed dependent light distribution* (vehicles
with LED headlights) -the speed dependent light
distribution adapts the light in towns and on
highways
or expressways. Intersections can also
be illuminated on vehicles
with a navigation sys­
tem*.
A WARNING
- Automatic headlights * are only intended to
assist the driver. They do not reliev e the
driver
of responsibility to check the head­
lights and to turn them on manually accord­
ing to the current ligh t and visibility condi­
tions. For example, fog cannot be detected
by
the light sensors . So always switch on the
low beam under these weather conditions
and when
driving in the dark ~D.
-If the battery is dra ining significantly, the
parking lights will switch off automatically
to reduce the risk of the engine not starting . ..,..

Downloaded from www.Manualslib.com manuals search engine Always make sure your vehicle is parked and
adequately lit according to the laws. Avoid
using
the parking lights for several hours.
Switch
on the right or left parking light if
possible.
-
Please observe legal regulations when using
the lighting systems described.
Tips
-The light sensor for the automatic head­
lights*
is in the rearview mirror mount.
Therefore, do not place any stickers in this
area on the w indshield.
-
Some functions of the exterior lighting can
be
adjusted ~page 3 7.
-
If yo u turn off the ign ition whil e the exterior
lights are on and open the door, you will
hear a warning tone.
- In some markets, the tail lights will switch
on when the daytime running lights switch
on.
- In cool
or damp weather, the inside of the
headlights, turn signals and tail lights can
fog over due to the temperature difference
between the inside and outside. They will
clear shortly after switching them on. This
does not affect the service life of the light­
ing.
Turn signal and high beam lever
The lever operates the turn signals, the high
beoms
and the headlight flasher.
@
,
I
@
Fig. 31 Turn signal and high beam lever
"' 0 0
a'.: CXl
Lights and Vision
Turn signals¢ Q
The turn signals activate when you move the lev­
er into a turn signal position when the ignition is
switched on.
@-right turn signal
@
-left turn signal
The turn signal blinks three times if you tap the
lever (convenience turn signal).
High beams and headlight flasher §D
Move the lever to the corresponding position:
®-high beams on
@-high beams off or headlight flasher
The . indicator light in the instrument cluster
turns on.
A WARNING
High beams can cause glare for other drivers,
which increases
the risk of an accident. For
this reason, only use the high beams or the
headlight flasher when they will not create
glare for other drivers.
Adjusting the exterior lighting
The functions are adjusted in the Infotainment
system .
... Select in the Infotainment system: IMENUI but­
ton> Vehicle > left control button >V ehicle set­
tings > Exterior lighting.
Automatic headlights
You can adjust the following settings in the Au­
tomatic headlights
menu:
Activation time -you can adjust ifthe headlights
switch on Early, Medium or Late according to the
sensitivity of the light sensor.
Audi adapti ve light* -you can switch adaptive
light On and Off.
Daytime running lights*
USA models : the daytime running lights can be
switched on or off using the MMI. Select On or
Off. ....
37

Downloaded from www.Manualslib.com manuals search engine Lights and Vision
Canada models: this function cannot be switched
off. They activate automaticall y each time the ig­
n ition is switched on. T his menu item is shown
with a "gray background".
Com ing home , Leaving home
The coming home function illuminates the area
outside the vehicle when you turn the ignition off
and open the driver 's door. To switch on the func­
tion, select Entry /exit lighting .
The leaving home ill uminates the area outside
the vehicle when you unlock the vehicle . To
switch
on the function, select Entry/exit light­
ing .
The coming home and leaving home f unctions
only operate when it is dark and the lig ht switch
is in
the AUTO position.
Emergency flasher
Fig. 32 Center conso le : eme rge ncy flash er button
The emergency flashers makes other drivers
aware of your vehicle in dangerous situations.
• Press the~ button to switch the emergency
flashers on or off.
You can indicate a
lane change or a turn when the
emergency fla sh ers are switched on by us ing the
turn sig nal lever. The emergency flashers stop
temporarily.
The emergency flashers also work when the igni­
tion is turned off.
(!) Tips
You should switch the emergency flashers on
if:
38
- You are the last c a r in a tra ffic jam so that
all other vehi cles approaching from behind
can see you, or if
- Your vehicle
has broken down or you are
having
an emergency, or if
- You r vehicle is
being towed or i f you are
towing another vehicle.
Interior lighting
Interior lighting
Fig. 33 Headlin e r: i nterior lighti ng
[!]-Door contact switch. The interior lighting is
controlled automatically.
A switch is no longer needed to switch the read­
ing lights on. A swiping movement or a brief tap
on the light is all that is needed to switch the
light on or off. If you hold your finger on the
reading light when switching it on, this ca n dim
the light down t o a certain level.
Interior light ing
There are other interior lighting functions that
are availab le. Several functions can be set in the
Infotainment system. Select in the Infotainment
system: I MENUl button > Vehicle > left control
b u
tton >Vehicle settings> Interior lighting.

Downloaded from www.Manualslib.com manuals search engine ..... N
G'. co ..... ID VI ..... ID .....
Instrument illumination
Fig. 34 Instrument illumination
The brightness of the instrument cluster and the
center console can be adjusted.
• Press th e knob to release it.
•Turn the knob toward"-" or"+" to reduce or in­
crease
the brightness.
•Press the knob again to return it to its original
position.
Vision
Adjusting the exterior mirrors
Fig. 35 Driver's door: knob for the exterior mirrors
Turn the knob to the desired posit ion:
Q/P -adjusting the left/right exterior mirror.
Move
the knob in the desired direction .
4iil -Heating the mirror glass depending on the
outside temperature .
8 -Folding exterior mirrors*. In the Infotain­
ment system, you can select if the mirrors fold in
automatically when you lock
the vehicle
~page29.
Lights and Vision
Front passenger's exterior mirror tilt
function*
To help you see the curb when backing into a
parking space,
the surface of the mirror tilts
slightly. For this to happen, the knob must be in
the position for the front passenger 's outside
mirror.
You can adjust the tilted mirror surface by turn­
ing the knob in the desired direction . When you
move
out of reverse and into another gear, the
new
mirror position is stored and assigned to the
key you are using.
The
mirror goes back into its original position
once you drive forward faster than 9
mph
(15 km/h) or turn the ignition off.
A WARNING
Curved mirror surfaces (convex) enlarge the
field of vision. However, they make objects in
the mirror appear smaller and further away.
Your may estimate incorrectly when you use
these mirrors
to gauge your distance from the
vehicles behind you when changing lanes -ac­
cident risk!
CJ) Note
If the mirror housing was moved by outside
f orces (such
as an impact when maneuver­
ing), you
must use the power folding function
to fold the mirror all the way out. The mirror
housing must not be moved back into place
by hand because
this would impair the func­
tion of the mirror mechanism.
@ Tips
If the power adjusting function malfunctions,
the glass in both mirrors can be adjusted by
pressing on
the edge of it by hand.
39