2016 AUDI A7 tow

-Tires on a vehicle that has
been overloaded can fail sud­
denly, including a blowout and
sudden deflation, causing loss
of control and a crash.
-Always make sure that the to ­
tal load being transported - including the weight of a trail­
er hitch and the tongue
weight of a loaded trailer -
does not make the vehicle heavier than the vehicle's
Gross Vehicle Weight Rating.
Determining correct load
limit
Use the example below to calcu­
late the total weight of the pas­
sengers and luggage or other
things that you plan to transport so that you can make sure that
your vehicle will not be overload­
ed.
Steps for Determining Correct Load Limit
1. Locate the statement "THE
COMBINED WEIGHT OF OCCU­
PANTS AND CARGO SHOULD
NEVER EXCEED XXX KG OR XXX
LBS"on your vehicle's placard
(tire inflation pressure label)
¢ page 243, fig. 19 7.
Wheels
2. Determine the combined
weight of the driver and pas­
sengers that will be riding in
your vehicle.
3. Subtract the combined weight
of the driver and passengers
from
"XXX" kilograms or "XXX"
pounds shown on the sticker
¢ page 243, fig . 197 .
4. The resulting figure equals the
available amount of cargo and
luggage load capacity. For ex­
ample, if the
"XXX" amount
equals
1400 lbs. and there will
be five
150 lbs. passengers in
your vehicle, the amount of
available cargo and luggage
load capacity is 650 lbs .
(1400-750 (5 X 150) = 650
lbs.)
5. Determine the combined
weight of luggage and cargo
being loaded on the vehicle.
That weight may not safely ex­ ceed the available cargo and
luggage load capacity calculat ­
ed in Step 4.
6. If your vehicle will be towing a trailer, load from your trailer
will be transferred to your vehi­
cle. Consult this manual to de­
termine how this reduces the ..,
247

M N <( I.J "". rl I.O
"' N I.O rl
Emergency assistance
Warning triangle
A pp lies to vehicles: Wi th wa rning tri angl e
D
\,-------:----- 11
Fig. 200 Luggage co mpa rtment l id : wa rnin g t ria n gle
The warning triangle p laced in the vehicle at the
factory is located in the luggage compartment .
• To open the cover, turn the locking mechanism
and pull the cover downward .
• Remove the warn ing triangle from its holder .
The luggage compartmen t lid is only designed to
hold the warning triangle offered by the original
accessories program .
Vehicle tool kit
Vehicle tool kit and jack
The vehicle tool kit is located in the luggage
comportment under the cargo floor cover .
Fig. 201 Lugg age co mpartment : ca rgo f loo r cover folded
up ward/ spa r e ti re
Em erg en cy ass is tan ce
Fig. 202 Trun k lid: Vehicl e too l kit
• Fold the floor to the seatback with the help of
t he hand le.
• Tu rn the handwheel counter-clockwise
r=;, fig. 201 and remove the spare tire to reach
the vehicle tool kit.
T he onboard tool kit includes :
- Hooks to remove the wheel covers*
- Plastic hook to remove wheel bol t covers"
- Wheel bolt wrench
- Alignment pin for changing wheels
- Screwdriver with reversib le b lade
- Tow ing eye
- Jack
Before storing the jack , make sure it is wound
back down as far as it will go .
A WARNING
'"' -Im proper use of the vehicle jack can cause se­
rious pe rsonal injuries .
- Never use the screw driver hex head to
tighten wheel bolts, since the bolts cannot attain the necessary tightening torque if yo u
use the hex head, po ten tially causing an ac ­
cident.
- The fa ctory-supplied jack is intended only
for your ve hicle model. Unde r no circum­
stances shou ld it be used to lift heavy
vehicles or other loads; you risk injuring
yourse lf.
- Never start the engi ne when the vehicle is
raised, which could cause an accident.
- Support the vehicle securely with appropri­
ate stands if work is to be pe rformed under­
neath the vehicle; otherwise, there is a po ­
tential risk for injury.
253

M N <( (.J
'SI: ,...., \!) 1.1'1
N \!) ,....,
Replacing wheels
Before changing a wheel
Observe the following precautions for your own
and your passenger's safety when changing a
wheel .
.,. After you experience a tire failure, pull the car
well away from moving traffic and try to reach
level ground before you stop¢,& .
.. All passengers should
leave the car and move
to a safe location (for instance, beh ind the
guardrail) ¢ ,& .
.,. Engage the
parking brake to prevent your vehi­
cle from rolling unintentiona lly ¢,& .
.. Move
selector lever to position P ¢ ,& .
1> lfyou are towing a trai ler, unhitch the trailer
from your vehicle .
.,. Take the
jack and the spare tire out of the lug­
gage compartment
¢ page 253, ¢ page 254.
.,&. WARNING
You or your passengers could be injured while
changing a wheel if you do not follow these
safety precautions:
- If you have a flat tir e, move a safe distance
off the road. T urn off the engine, turn the
emergency flashers on and use other warn­
ing devices to alert other mo torists.
- Make sure that passengers wait in a safe
place away from the vehicle and well away
from the road and traffic.
- T o help prevent the vehicle from moving
sudden ly and possibly slipping off the jack,
always fully set the parking brake and block
the wheel diagonally opposite the wheel be­ ing changed. When one front wheel is lifted
off the ground, placing the Automatic Trans­
mission in P (Park) will
not prevent the vehi­
cle from moving.
- Before you change a wheel, be sure the
ground is level and firm . If necessary, use a
stu rdy board under the jack.
- Always store the vehicle tool kit, the jack
and the replaced tir e in the luggage com­
partment ¢
page 132.
Emergency assistance
{!) Tips
Before changing the whee l, you must activate
the jacking mode, so that the automat ic con­
trols for the Adapt ive Air Suspension* do not
make it more difficult to lift the vehicle with
the jack ¢
page 257 .
Changing a wheel
When you change a wheel , follow the sequence
described below step-by-s tep and in exactly tha t
order .
l. Activate the vehicle jack mode* ¢ page 2 5 7.
2. Remove the
decorative wheel cover*. For
more details see also¢
page 256, Decora ­
tive wheel covers
or¢ page 256, Wheels
with wheel bolt caps .
3. Loosen the wheel bolts ¢page 256.
4. Locate the pro per mounting point for the
jack and align the jack be low that point
¢page 257.
5. Raise the car with the jack¢ page 257 .
6. Remove the wheel with the flat tire and then
install
the spare ¢ page 259.
7. Tighten all wheel bolts ligh tly.
8.
Lower the vehicle with the jack .
9. Use the wheel bolt w rench and
firmly tighten
all wheel bolts¢
page 256 .
10. Replace the decorative wheel cover*.
11. Deactivate the vehicle jack mode* in the
MMI :
ICAR I funct ion button > (C ar)* systems
control button > Servicing & checks > Air
susp.: jack mode > Off .
The vehicle jack mode* switches off automatically
at speeds above 6 mph (10 km/h) .
.,&. WARNING ~ -
Always read and follow all WARNINGS and in ­
formation ¢
.& in Raising the vehicle on
page 258
and ¢ page 260.
255

M N <( (.J
'SI: ,...., \!) 1.1'1
N \!) ,....,
Emergency situations
General
This chapter is intended for trained emergency
crews and working personnel who have the nec­
essary tools and equipment to perform the se
operations.
Starting by pushing or
towing
(D Note
Vehicles w ith an automatic transmission can­
not be started by push ing o r tow ing.
Starting with jumper
cables
If necessary, the engine can be started by con­
necting it to the battery of another vehicle .
If the engine should fail to start because o f a dis­
charged or weak battery, the battery can be con­
nected to the battery of
another vehicle, us ing a
pair of jumper cables to start the engine .
Jumper cables
Use only jumper cables of sufficiently large cros s
section
to carry the starter current safe ly. Refer
to the manufacturer's specifications.
Use only jumper cables with
insulated term inal
clamps which are distinctly marked:
plus(+) cable in most cases co lored red
minus (-) cable
in most cases colored black .
A WARNING
Batteries contain electricity, acid, and gas .
Any of these can cause very ser ious or fatal in­
jury . Fo llow the instructions be low for safe
handling of your vehicle's battery.
- Always shield your eyes and avoid leaning
over the battery whenever possible.
- A discharged battery can freeze at tempera­
tures just below 32 °F (0 °C) . Before con­
necting a jumper cable, you must thaw the
Emergency situations
frozen battery completely, otherwise it
could explode .
- Do not allow battery acid to contact eyes or
skin. Flush any contacted area with water immediately.
- Improper use of a booster battery to start a
veh icle may cause an explosion.
- Vehicle batteries generate explosive gases .
Keep sparks, flame and lighted cigarettes
away from batteries.
- Do not try to jump start any vehicle with a
low acid level in the battery.
- The voltage of the booster battery must al ­
so have a 12-volt rating. The capacity (Ah) of
the booster battery should not be lower
than that of the discharged battery. Use of batteries of different voltage or substantial­
ly different" Ah" rating may cause an explo­
sion and personal injury.
- Never charge a frozen battery . Gas trapped
in the ice may cause an explosion .
- Never charge or use a battery that has been
frozen . The battery case may have be weak­
ened ,
- Use of batter ies of different voltage or sub­
stantially different capacity (Ah) rating may
cause an exp losion and injury. Th e capacity
(Ah) of the booste r battery should not be
lower than that of the discharged battery.
- Before you check anything in the engine
compartment, always read and heed a ll
WARNINGS
q page 218 .
(D Note
-Applying a h igher voltage booster battery
w ill cause expensive damage to sensitive
electronic components, such as control
units, relays, radio, etc.
- Th ere must be no ele ct rical contact between
the vehicles as otherwise current could al­
ready start to flow as soon as the positive
(+) termina ls are connected.
(D Tips
The discharged battery must be properly con-
nected to the vehicle's e lectrical system. .,..
265

M N <( I.J "". rl I.O
"' N I.O rl
(D Note
Improper hook-up of jumper cables can ruin
the generator.
- Always connect POSITIVE( +) to POSITIVE
( + ), and NEGATIVE( -) to NEGATIVE(-)
ground post of the battery manager control
unit.
- Check that all screw plugs on the battery
cells are screwed in firmly. If not, tighten
plugs prior to connecting clamp on negative
battery terminal.
- Please note that the procedure for connect­
ing a jumper cable as described
above ap­
plies specifically to the case of your vehicle
being jump started. When you are giving a
jump sta rt to another vehicle, do
not con­
nect the negative(-) cab le to the negative
( - ) terminal on the discharged battery @
r:::;, fig. 216. Instead, secure ly connect the
negative(-) cab le to either a solid metal
component that is firm ly bolted to the en­
gine block or to the engine block itself. If
the battery that is being charged does not
vent to the outs ide, escap ing battery gas
could ignite and explode!
Towing with a tow truck
General hints
Your Audi requires special handling for towing.
The follow ing information is to be used by com­
mercial tow truck operators who know how to op­
erate their eq uipment safe ly.
- Never t ow your Audi. To wing will cau se da m ­
age to the engine and tran smi ssion .
- Neve r wrap th e safety cha in s or win ch cab le s
around the brake line s.
- To pre vent unnecess ary dama ge, your A udi
mu st b e trans port ed w ith a fl at b ed t ru ck .
- To lo ad the vehicle on to th e flat bed, us e the
towing l oop found in th e vehicle tool s and at­
tach to th e fr ont or re a r anc hora ge
¢ page 267 and ¢page 268.
Emergen cy situati ons
A WARNING
-A veh icle being towed is not safe for passen-
gers. Neve r all ow anyone to ride in a vehicle
being towed, for any reason .
Front towing loop
Fig. 217 Fro nt bumper: cover
Fig . 2 18 Fro nt bumper : insta lling the tow ing loop
The threaded opening for the towing loop is lo­
cated behind a
cover on the right side of the front
bumper .
.,. Remove the towing loop from the vehicle tool
kit¢
page 253.
.,. Press the lower area of the cap inward with
quick, strong pressure
r::;, fig . 217 . The cap w ill
loosen from the bumper .
.,. Tighten the towing loop in the threaded open­
ing until it stops
¢ fig. 218 and then tighten it
w ith a wheel wrench .
.,. After using, p lace the towing loop back in the
vehicle tool k it.
A WARNING
--
If the towing loop is not tightened until it
stops when installing, the threads may be
267

Emergency situations
pulled out when towing the vehicle and that
could cause an accident.
Rear towing loop
Only install the rear towing loop when it is need­
ed.
0 0
Fig. 219 Rear bumper: c over
0 0
Fig. 220 Rear bump er: sc rew ing in towing loop
There are threads located behind the right side of
the rear bumper where a towing loop can be in­
stalled. The threads are located behind a cover.
" Remove the towing loop from the vehicle tool
kit .
.. Press inward strongly to the button side of the
cap to remove it from the bumper
r=;,fig. 219 .
"Screw the towing loop tightly in the threaded
hole as far as it will go and tighten it with the
wheel wrench
r=;, fig. 220.
Remove the towing loop when you are done using
it and place it back in the vehicle tool kit . Always
keep the towing loop in the vehicle.
&_ WARNING
If you do not screw the towing loop complete­
ly, it could come out of the threaded hole
while the vehicle is being towed causing dam·
268
age to the vehicle and possible serious per­
sonal injury .
Loading the vehicle onto a flat bed truck
Fig. 221 Vehicle on flat bed tru ck
Front hook up
:g N 0 t!, .., m
"Align the vehicle with the centerline of the car
carrier ramp .
.. Attach the w inch hook to the front towline eye
previously installed.
Rear hook up
"Align the vehicle with the centerline of the car
carrier ramp .
.. Attach the winch hook to the rear towline eye
previously installed.
@ Tips
Check carefully to make sure the hook-up is
secure before moving the car up the flatbed
truck ramp.
Vehicle transport
Whenever you hove your vehicle transported, be
sure to note the following:
(D Note
Mount the tie-down chains/cables over the
running surface (circumference) of the tires.
Never secure the vehicle by the axle, the sus­
pension struts or the front or rear towline
eye. For technical reasons, the pressure in the
suspension struts may change during the
transport and this will adversely affect vehicle handling.

Consumer information
Consumer information
Warranty coverages
Your Audi is covered by the following warran­
ties:
- New Vehicle Limited Warranty
- Limited Warranty Against Corrosion Perfora-
tion
- Emissions Control System Warranty
- Emissions Performance Warranty
- California Emissions Control Warranty (USA
vehicles only)
- California Emissions Performance Warranty
(USA vehicles only)
Detailed information regarding your warranties
can be found in your
Warranty & Maintenance
booklet .
Operating your vehicle
outside the U.S.A. or
Canada
Government regulations in the United States and
Canada require that automobiles meet specific
emission regulations and safety standards.
Therefore, vehicles built for the U.S.A. and Cana­
da differ from vehicles sold in other countr ies.
If you plan to take your veh icle outside the conti­
nenta l limits of the United States or Canada,
there is the possibility that:
- unleaded fuels for vehicles with catalytic con­
verter may not be available;
- fuel may have a considerably lower octane rat ­
ing . Improper fuel may cause engine damage;
- serv ice may be inadequate due to lack of proper
serv ice facilities , tools or testing equipment;
- r eplacement parts may not be readily available .
- Nav igat ion systems for vehicles built for the
U.S.A. and Canada will not necessar ily work in
Europe, and may not work in othe r countries
outside North America .
274
(D Note
Aud i cannot be responsib le for mechanical
damage that could result from inadequate
fuel, service or parts availability.
Audi Service Repair
Manuals and Literature
Audi Offic ial Factory Service Manuals and Litera­
ture are published as soon as possible after mod­
el introduction. Service manuals and literature
are available to order from the Audi Technical Lit ­
erature Ordering Center at:
www.audi.techliterature .com
Maintenance
General '
Your vehicle has been designed to help keep
maintenance requirements to a minimum. How­
ever, a certain amount of regular maintenance is
still necessary to assure your veh icle's safety,
economy and reliability. For deta iled vehicle
maintenance consult your Warranty & Mainte­
nance booklet .
Under difficult operating conditions, for exam­
ple at extremely low outs ide temperatures, in
very dusty regions, when towing a trailer very fre­
quently , etc., some service work should be per­
formed between the intervals specified. This ap­
plies particularly to:
- oil changes, and
- cleaning or replacing the air filter .
'
@) For the sake of the environment
By regularly maintaining your vehicle, you
help make sure that emission standards are
maintained, thus minimizing adverse effects
on the environment.
Important considerations for you and your
vehicle
The increasing use of electronics, sophisticated
fuel injection and emission control systems , and
the generally increasing technical comp lexity of
llJJ,

Index
l
Jac k 253
265
266
J
ump-starting .. .. ... .... .... .. ... ... .
J umper cables .. .. ............. .. .. .. .
K
Key ... .. .. .. .... ... . ...... ... .. .. .... 30
Eme rgency key . . . . . . . . . . . . . . . . . . . . . . . 30
Indicator light . . . . . . . . . . . . . . . . . . . . . . . 77
Key not recogni zed . . . . . . . . . . . . . . . . . . . . 77
K ey replacement . . . . . . . . . . . . . . . . . . . . . 30
Maste r key . . . . . . . . . . . . . . . . . . . . . . . . . . 30
M echanical key . . . . . . . . . . . . . . . . . . . . . . . 30
R eplacing th e batte ry . . . . . . . . . . . . . . . . . 3 1
Kick-down (a utomat ic transm ission) . . . . . . 111
Knee airbags . . . . . . . . . . . . . . . . . . . . . . . . . 1 59
D escript ion . . . . . . . . . . . . . . . . . . . . . . . . . 159
H ow they wo rk . . . . . . . . . . . . . . . . . . . . . . 160
Important safety instructions . . . . . . . . . . 161
L
Lane assist
refer to Act ive lane assist . . . . . . . . . . . . . . 94
L A T CH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
D escr ip ti on . . . . . . . . . . . . . . . . . . . . . . . . . 18 1
I nstal ling a child restraint . . . . . . . . . . . . . 18 2
L ocation . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
M ounting and re leasing the ancho rage
hook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
L aunch cont ro l program . . . . . . . . . . . . . . . . 111
Leather care/cleaning . . . . . . . . . . . . . . . . . . 208
L eaving home . . . . . . . . . . . . . . . . . . . . . . . . . 45
Lifting jack . . . . . . . . . . . . . . . . . . . . . . . . . . 257
Light Ambient lighting . . . . . . . . . . . . . . . . . . . . . 46
Com ing/Leavi ng home. ..... ... .. .. .. .. 45
Daytime r unning lights . . . . . . . . . . . . . . . . 43
E me rg ency flashers . . . . . . . . . . . . . . . . . . . 46
H eadlig ht ass ist . . . . . . . . . . . . . . . . . . . . . . 44
H igh beam . . . . . . . . . . . . . . . . . . . . . . . . . . 44
I nter ior/ readi ng lights . . . . . . . . . . . . . . . . . 46
L ow beams . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Parking lights . . . . . . . . . . . . . . . . . . . . . . . . 43
Rear fog lights . . . . . . . . . . . . . . . . . . . . . . . 43
T u rn signa ls . . . . . . . . . . . . . . . . . . . . . . . . . 44
284
Light/ rain senso r
Hea dlights . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Ind icator light . . . . . . . . . . . . . . . . . . . . . . . 22
Intermittent (w indshie ld wipers) . . . . . . . . 49
L ight ing
Exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Interio r . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
L ights
Head light r ange control system . . . . . . . . . 43
Load ing the roof rack . . . . . . . . . . . . . . . . . . . 62
Locking Power locking switch . . . . . . . . . . . . . . . . . . 35
Remote contro l . . . . . . . . . . . . . . . . . . . . . . 33
U sing the key . . . . . . . . . . . . . . . . . . . . . . . . 35
Low beam In dicator light ..... .. ... . .... ... .. .. . 21
Low beams . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Lower universa l anchorages (Canada) . . . . . 180
Luggage compar tment
12 Volt so cket . . . . . . . . . . . . . . . . . . . . . . . 59
Cargo net . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Cove r.. ... .. .... .. .. .. .. .. .... ... .. . 63
E nlarging . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Load ing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Reve rsible mat . . . . . . . . . . . . . . . . . . . . . . . 65
Ski sack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Stor ing cargo co rrectly . . . . . . . . . . . . . . . 132
Stow ing luggage . . . . . . . . . . . . . . . . . . . . 132
T ie-downs . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
T ru nk p ass- through . . . . . . . . . . . . . . . . . . . 66
Luggage compartment l id
Clos ing button . . . . . . . . . . . . . . . . . . . . . . . 36
Emergency re lease . . . . . . . . . . . . . . . . . . . . 38
movement -act ivated opening . . . . . . . . . . . 38
Open ing/closing . . . . . . . . . . . . . . . . . . . . . . 36
Lumbar suppor t
Front seats . . . . . . . . . . . . . . . . . . . . . . . . . . 54
M
Maintenance .. .. .. ... ............. ... 274
Maintenance interva ls . . . . . . . . . . . . . . . . . . 26
Malfunction Ind icator Lamp (M IL) . . . . . 20 , 28
Manual shift program. ............... ..
111
M assage func tion
Front seats . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Mechan ica l key . . . . . . . . . . . . . . . . . . . . . . . . 30