Emergency assistance
-Make sure that passengers wait in a safe
place away from the vehicle and well away
from the road and traff ic.
- Make sure jack position is correct, adjust
as necessary and then cont inue to raise
the jack.
(D Note
Do not lift the vehicle by the sill. Position the
vehicle jack only at the designated lifting points on the sill. Otherwise, your vehicle will
be damaged.
Taking the wheel off /installing the spare
tire
Follow these instructions step-by-step for chang
ing the wheel .
Fig. 179 Changing a wheel: using the screwdriver handl e
(with the blade removed) to turn the bolts
Fig. 180 Changing a wheel: alignment pin insid e the top
hole
After you have loosened all wheel bolts and raised the vehicle off the ground, remove and re
place the whee l as follows:
Removing the wheel
• Remove the topmost wheel bolt comp letely
with the
hexagonal socket in the screwdriver
230
handle (vehicle tool kit) ¢ fig. 179 and set it
aside on a
clean surface.
• Screw the threaded end of the
alignment pin
from the tool kit hand-tight into the empty bolt
hole ¢
fig. 180.
• Then remove the other wheel bolts as described
above.
• Takeoff the whee l leaving the alignment pin in
the bolt hole¢ (!).
Putting on the spare tire
• Push the spare tire over the alignment pin.
• Screw on the wheel bolts and tighten them
slightly using the hexagonal socket.
• Remove the alignment pin and insert and t ight
en the remaining wheel bolt slightly like the
rest.
• Tur n the jack hand le counter-clockw ise to lower
the vehicle until the jack is fully released.
• Use the wheel bolt wrench to tighten a ll wheel
bolts firmly ¢
page 228. Tighten them in a
crisscross pattern,
from one bolt to the (ap
proximately) opposite one, to keep the wheel
centered.
• Perform the steps required after chang ing the
wheel¢
page 227, A~er changing a wheel.
The hexagonal socket makes it easier to remove
the wheel bo lts from the rim . Care should be tak
en when removing the reversible blade.
(D Note
When removing or installing the wheel, the
rim could hit the brake rotor and damage the
rotor . Work carefully and have a second per
son to help you.
(D Tips
-When mounting tires with unidirectional
tread design
make sure the tread pattern is
pointed the right way¢
page 231.
-The wheel bolts should be clean and easy to
turn. Check for dirt and corrosion on the
mating surfaces of both the wheel and the
hub. Remove all dirt from these surfaces be
fore remounting the wheel.
Emergency situations
Raising the vehicle
Lifting with workshop hoist and with floor
jack
Th e vehicle may only b e lift ed at the lifting
poin ts illust rated.
F ig .. 19 2 Fro nt lift ing po int
F ig. 193 Rea r lifti ng po int
.,. Read and heed WARNING ¢ A-
.,. Locate lifti ng po ints ¢ fig . 192 and ¢ fig. 193.
.,. Adjust li fting arms of wo rkshop hoist or floor
jack to match veh icle lifting points.
.,. In se rt a rubb er pad between t he floor jack/
wor kshop hoist a nd the lif ting poin ts .
If you must lift your vehicle with a floor jack to
work underneath, be sure the vehicle is safely
supported on stands intended for this purpose .
Front lifting point
The lift ing po int is located on the floo r pan re in
forcement about at the same leve l as the jack
mo unt ing point ¢
fig. 192 . Do not lift the vehi
cle at the vertical sill rei nforcement.
Rear lifting point
The lift ing po int is located on the vertica l re in
for cement of the lower sill fo r the on board jack
¢fig. 193.
240
Lifting with vehicle jack
Refer to ~ page 229.
A WARNING
- To re duce the r is k of serious injury and vehi
cle dama ge .
- Always lift the vehicle o nly at the special
workshop hois t an d floor jack lift points il
l ustrat ed
~ fig. 192 and ~ fig. 193.
- Failure to lift the v ehicle at these points
could ca use the veh icle to tilt or fall from
a lift if the re is a cha ng e i n ve hicle weigh t
dis tribu tion and ba lan ce . T his mig ht hap
p en, for exa mple, whe n he avy co mpo
n en ts such as the engine block o r tr an s
mission are removed.
- W hen re m ov in g h eavy co mponen ts like
these, an cho r veh icle to hoist or ad d co rre
spond ing weights to ma inta in the ce nter of
gravity . Othe rw ise, the vehicle mi ght t ilt o r
slip off t he hoist, causing serious pe rsonal
in jur y.
(D Note
- Be aware of the fo llowing po ints befo re lift
ing the vehicle:
- The vehicle should never be lifted or
jacked up from underneath the engine oil pan, the transmission housing, the front
or rear axle or the body side members .
This could lead to serious damage .
- To avoid damage to the underbody or
chassis frame, a rubber pad must be in
serted between the floor jack and the lift
points.
- Before driving over a workshop hoist,
check that the vehicle weight does not
exceed the permissible lifting capacity of
the hoist.
- Before driving over a workshop hoist , en
sure that there is sufficient clearance be
tween the hoist and low parts of the ve
h icle.
