2016 AUDI A3 heating control

Driving
Otherwise, there is the r isk that the vehicle
could roll.
- After the engine has been switche d off, the
radiator fan can continue to run for up to 10
minutes - even with the ign ition switched
off . It ca n also switch on again after some
t i me if the coolant tern perature rises as the
resul t of heat buildup or if the engine co m­
partment is heat ed by the su n's rays and the
eng ine is ho t.
(D Note
- If t he engine has been unde r heavy load for
an extended pe riod of time, heat builds up
i n the eng ine compartment after the eng in e
i s sw itche d off- the re is a risk of dam ag ing
the engi ne . Fo r thi s reaso n, let the e ng ine
run for at id le for approxim ately two mi ­
nutes befo re sh utting it off .
Starting and stopping
the engine (vehicles with
a convenience key)
Engine with the
button Starting
App lies to vehicles: w ith conve nien ce key
The I START ENGINE STOP I button switches the
igni tion on and s tar ts the engine.
F ig . 78 Cente r conso le : STAR T ENGIN E ST OP butto n (w ith
co nve nience key)
You can start yo ur car w ithout using your conven­
ience key . You must simp ly be c arrying the key
with you .
Plug-in hybrid drive* : refer to the informatio n for
starting the vehicle under ¢
page 100.
82
Switching the ignition on /off or preheating
If thP 'Tij ind icator lig ht blinks and the mess age
Plea se move steerin g wheel appears when
switching the ignition on, the stee ring is locked
by the steer ing lock . In th is case, turn the steer­
i ng wheel slightly to the left/right.
.,. To switch the ignit ion on or off, press t he
I STAR T ENGINE STOPI button . Do not press the
brake pedal while doing this .
The need le in the t achome ter moves to
READY
whe n the ignition switches on an d moves to OFF
when the ignition switches off .
D iesel ve hicles are p rehea te d while the ig nition is
switched on
Iii .
Starting the engine
Your vehicle is equipped with la unch control. The
engine starts a utomat ica lly when you press the
I START E N GIN E STOP ! button br iefly.
.,. Press the brake pedal and move the selector
lever to the P or N position .
.,. Press the
I START E NGINE STOP ! button briefly .
T he engine w ill sta rt.
Major elect rical equipment sw itches off tempora­
rily whe n starting the eng ine .
It is possible that there will be a s light de lay
when starting the engine in d iesel veh icles in
colder temperatures . Therefore, you must hold
the b rake pedal down until the eng ine starts . Th e
i ndica to r light turns on wh ile the engi ne is pre­
hea ting
Iii .
The preheating t ime depends o n the coolant
temperat ure and outside temperature . The glow
pl ug indica to r li ght
II will only tu rn on for ap­
prox im ately 1 se co nd when the engi ne is warm o r
t h e ou ts ide temperat ure is higher th an 8
°C. Tha t
me ans you can s tart t he engine
immedia tely .
If th e engine does not start immediately, stop
th e starti ng p ro cedure by pushi ng the
I S TAR T EN GINE ST OP ! button ag ain an d repe at
a ft er 30 seconds. ..,.

,....,
N
0 > co ,...., Launch Control-Program
Applies to vehicles: with launch control
The Launch Control Program enables maximum
acceleration .
Requirement: the engine must be at operating
temperature and the steering wheel must not be
turned .
.. With the engine running, press the
l~OFF ! but­
ton briefly one time
ll .
.. Pull the selector lever back out of the D/S posi­
tion briefly to select the S position, or press it
toward the right into the tiptronic pos ition or
select the
D ynami c driving mode in drive se­
lect*
~page 148.
.. Press the b rake peda l firmly wi th you r left foot
and hold it all the way down for at least 1 sec­
ond.
.. At the same time, press the gas pedal all the
way down with your right foot until the engine
reaches and stays at a high RPM level.
.. Remove your left foot from the brake.
A WARNING
-Always adapt yo ur driv ing to the traffic flow.
- Only use Launch Control when road and traf-
fic cond itions allow it and other dr ivers will
not be endangered or impacted by you r d riv­
ing and the vehicle's accele ration.
- Please note that the drive whee ls can sp in
and the vehicle can break away when sport
mode is swit ched o n, especia lly when the
road is s lippery.
- Once t he vehicle has sta rted moving, press
the
I $? OFF ! button briefly to t urn the sport
mode off.
(D Tips
- The transmiss ion temperature may increase
s ignificantly after using the lau nch cont rol
program.
If that happe ns, the program m ay
l) In vehicles w ith a d river information system, an ESC light
in the instrument cluster stays o n continuous ly and the
message
Stabili za tion contro l (E SC ): sport . Warning! Re·
stricted st abi lity
appears temporar ily.
Autom atic tran sm iss ion
not be ava ilab le for a few minutes. It will be
avai lab le again after a cool-down period.
- Whe n accelerating using the launch contro l
program, all vehicle parts a re su bject to
heavy loads. This can lead to increased
wear.
Emergency mode
Applies to vehicles: wit h S tronic transmiss ion
In the event of o system mo/function, there is on
emergency program.
If all of the selector lever positions are hig hlight­
ed with a light background in the instrument
cluster disp lay, there is a system malfunction and
the S tronic transmission is running in the emer­
gency program. The vehicle can still be driven in
emergency mode, but only with reduced speed
and not in all gears . In some cases, the vehicle
cannot drive in rever se .
(D Note
If the transm ission runs in emergency mode,
drive to an authorized A udi dealer or author­
iz ed Audi Se rvice Facility immed iate ly to have
the malfunc tion corrected.
Transmission malfunction
• Tran smi ssion malfunction ! Pl ea se stop the
vehicle and select P
The re is a ma lfunction in the transmission. Park
the vehi cle secure ly and do not cont in u e driv ing.
See a n author ized Audi dealer or au thori zed A udi
Service Facility for assis tance.
• Tran smission overheating! Plea se stop the
vehicle!
The transmiss ion is too hot and can become dam­
aged. Stop and let the transmiss ion cool w ith the
engi ne r unning (at idle) in the P se lector lever po­
s it ion. Then the ind icator lig ht and the message .,.
95

.... N
0 > CX)
.... I.Cl U"I ,....,
I.Cl ....
-To reduce the risk of overheating during op­
eration, do not place the Audi e-tron charg­
in g system in d irect sunlight for long peri­
ods of time.
- If the temperature inside the control unit
rises above 176 °F (80 °C), the charg ing
process will stop automatically until the
temperature decreases back down to the normal range .
Attaching/changing the power/vehicle
cable
Applies to vehicles: with plug-in hybrid drive
Fig. 101 Contro l unit : loosening the cable
Fi g. 102 Contro l unit : attaching t he ca ble
Requirements:
.,. The charging process for the high -voltage bat ­
tery must be ended .
.,. The vehicle charging connector must be re­
moved from the vehicle charging port.
.,. The power cable must be removed from the
socket.
Loosening the cable
.,. If necessary, loosen the screw ©¢ fig. 101 us­
ing the screwdriver provided.
.,. Lift the lever @all the way up .
e-tron
.,. Pull the connecto r@ out just until you feel re­
sistance .
.,. Close the lever @unt il it is rest ing on the con-
nector @.
.,. Remove the connector @ completely.
Attaching the cable
.,. Lift the lever @ up slight ly¢ fig. 102.
.,. Insert the connector @ into the control unit
just unti l you feel resistance .
.,. Lift the lever @all the way up.
.,. Insert the connector @ all the way into the
control unit.
.,. Close the lever @ .
.,. Tighten the screw © using the screwdriver pro­
vided .
.&_ WARNING
- Always remove the power cable from the
socket before changing the power cable or
vehicle cable.
- Always follow the instructions given when
charging the high -voltage battery. Do not
remove the vehicle charging cable from the
socket during the charging process. End the
charging process before removing the vehi­
cle charging cab le from the socket.
- On ly change cab les in a dry environment.
- The Audi e-tron charging system may only
be used as one un it composed of power ca­
bles, the control unit and vehicle cable. We
recommend using only cables approved by
Aud i.
113

e-tron
"'Slide the cover carefully to the side if necessa­
ry.
"' Remove the lock on the charging port
<=>fig . 109.
"'Insert power plug @ or© into the socket
<=>page 112, fig . 100.
"'Plug the vehicle charging connector ©
<=> page 112, fig . 100 into the vehicle charging
port <=>
fig. 109. The charging process starts au­
tomat ically if no charging timer is set.
(D Tips
Remove ice and snow from the cover using a
hand brush and solvent-free deicing spray.
Charging
App lies to veh icles: w ith plug- in hybrid drive
You can switch between the immediate charging
@ and charging timer(!) options during the
charging process if a charging timer is set. Press
the desired button to do this.
You have different charging options.
Immediate charging
To start the charging process immediately, press
the button @<=>page
115, fig. 107. The LED in
the button turns on.
Setting the charging timer
You can put a time delay on charging using the
charging timer in the MMI
l) You can set two dif­
ferent t imers.
"'If a timer was already set, press the button
(D
<=>page 115, fig . 107. The LED in the button
turns on .
"'To set a charging timer, press:
IM ENUI function
button
> Car> Car systems > Charging & e­
tron mode> Timer selection> Change timer.
"' Select Single timer or Repeat timer.
"' Set the time , date or day of the week.
"' You can activate climate control while charging
with the charging timer by selecting
Air condi ­
tioner
with the control knob. A./ appears in the
box . This activation is independent from the
l) Not availa ble in all Info ta inm en t system s.
116
MMI settings in the climate control menu
qpoge 122.
"' Press the ~I B_A_C_K~I button.
"' To activate the desired timer, confirm the set­
ting with the control knob. A./ appears in the
box.
Power save mode
Power save mode is automatically switched on
when the control unit has not been operated for
more than one minute. The
LED @<=>page 115,
fig. 106
stays on . All other displays turn off.
"' To switch power save mode on or off , press the
button
~ @ ¢page 115, fig. 106.
Power save mode ends automatically when the
vehicle charging connector is plugged into the ve­
hicle .
The high-voltage battery is charging when the
LED @blinks.
(D Tips
- Th e high-voltage battery also charges in
power save mode.
- If the charging process is in progress, it will
not be interrupted when power save mode
switches on.
- T he charging process can be interrupted at
any t ime. Press the active button on the ve­
hicle to do this
<=>page 115, fig. 107.
- The climate control output while charging
depends on the capacity of the electrical
connection. Additional information on cli­
mate control can be found under
<=> page 122.
'
-Air conditioning and heating is electric if
you select climate control using the charg­ ing timer. This may also be used in confined
spaces such as garages.
Setting the charging power level
App lies to vehicles: wit h pl ug-in hybr id drive
The control unit automatically recognizes the
voltage and the available current strength. You .,.

e-tron
Status displays
Applies to vehicles: w ith plug-in hybrid drive
You can check the various operating statuses us- unit@~ page 115, fig. 106 and the status LED
ing the LED@, the disp lay fie ld on the control
@ ~page 115, fig. 107 .
Charging system: control unit
LED on the control
Symbol Error code unit@ Meaning
Solution
Blue Flashes Self test
On Cable inserted correctly
Green Cable inserted and charg-
Flashes
mg
Self test completed sue-
cessfu lly, cable is not con-
White On nected or is is connected Insert the cable correctly.
incorrectly to the vehicle
charging port.
330 or Cable inserted incorrectly Check the cable and
insert
Red On
it correctly or replace the
340 or
fau [ty .
cable.
Disconnect the control
450, 500, unit from the power sup-
460, 200, ply and have the malfunc-
210,260, Red On Error in the control
unit. tion corrected at an au-
410 or thorized Audi dealer or au-
490 thorized Audi Service Fa-
cility
The control unit is over- A
llow the contro l unit to
cool down or operate it in
180,190 Red On heating or not cooled
the specified temperature
enough. range.
Have the malfunction cor-
140,130 Red On Communication to the ve-
rected by an authorized
or470 hide is malfunctioning. Audi dealer or authorized
Audi Service Facility.
300,310, Error in the household in-Have the
electrical instal-
Red On lation checked by a quali-
390 stallation.
fied electrician.
...
118

e-tron
You can release cover using the emergency re­
lease.
.,. Turn the lock to the horizontal position .
.,. Unlock the veh icle.
.,. Open the hood
r:!;> page 23 7, Opening the hood .
.,. Carefully pull on the knob @until there is re-
s istance .
.,. Turn the lock to the vertical position
r:!;> page 115, fig . 108 .
.,. Slide the cover carefully to the side if necessa­
ry .
Climate control
Description
Applies to vehicles: with plug- in hybrid drive
Your vehicle has either auxiliary heating or auxili­
ary heat ing/ air conditioning*.
The auxiliary heating or the auxi liary heating/ air
conditioning* switches on depending on the out­
side temperature and the temperature set on the
climate control unit .
Switching on/off immediately
.,. You can switch the climate control on and off
immediately in the MMI*
¢page 123. Or
.,. Switch off the blower with the~ button
¢ page 72, fig. 72.
Setting the timer
.,. You can set the time when your vehicle should
reach the desired temperature. Your set tem­
perature and the outside temperature deter­
mine when the climate control switches on.
@ Tips
- The temperature that the climate control
system adjusts to depends on the last tem­
perature you set in the climate control unit
c;;,page 72.
-The climate control system does not auto­
matically switch on or off earlier if the vehi­
cle battery charge or the fuel level is too low.
122
· Auxiliary climate control
Applies to vehicles: with plug-in hybrid drive without auxiliary
hea ting
The aux iliary climate control controls the tem­
perature in the vehicle inter ior ent irely with elec­
tric power. It turns on only if the high-voltage
battery charge level is sufficient and there is
enough fuel in the tank.
Auxiliary heating / air conditioning
Applies to vehicles: with plug-in hybrid drive and auxiliary
heat ing
The aux iliary heating/ air conditioning controls
the temperature in the vehicle interior if the
high-voltage battery charge level is suff icient and
there is eno ugh fuel in the tank.
The
.ill. symbo l blinks in the climate contro l unit
whe n auxiliary heating is switched on.
When the auxiliary heating/ air conditioning t im­
er is programmed, the Ill symbol stays turned on
until the departure t ime is reached.
& WARNING
- To reduce the risk of poisoning, the auxiliary
heating/ air conditioning must not run in
confined spaces .
- To redu ce the risk of fires, the auxiliary
heating/ air conditioning must not run
when refueling.
- Due to the high temperatures that result
from operating the auxiliary heating/ air
conditioning, the vehicle must be parked in
a way so that the hot exhaust can escape at
the bottom of the engine cover without ob­
struction. The exhaust must not come into
direct contact with highly flammab le mate­
r ials.
(D Tips
Water vapor can build up near the engine
compartment when outside temperatures are low. This is a natural phenomenon and is no
cause for concern.

Switching on/off immediately in the MMI1l
Applies to vehicles: with p lug- in hybrid drive
Bordbuch~
Standheizung / -k llmatlslerun g ~
Standheizung/ -k limat isierung einschalten
Timer 1: So 10 .11. 0:00
D
Timer p rog rammie ren •
Car Systeme
Fig. 112 MMI example: sw itching t he auxilia ry heat ing/
air co ndit io nin g• o n/off immediate ly
Switching the auxiliary climate control on/
off:
.,. Se lect the I MENU I button > Car> Car Systems >
Aux. climate control
> Turn on auxiliary cli­
mate control or Turn off auxiliary climate con­
trol.
Switching the auxiliary heating / air
conditioning* on/off:
• Sel ect th e I MENU
I bu tto n > Car > Car Systems >
Auxiliary heating / air conditioning
> Turn on
auxiliary heating / air conditioning or Turn off
auxiliary heating/ air conditioning .
(D Tips
T he au xili ary cl imate contro l or the aux iliary
he ating / air cond itioni ng* ca n als o be sw itch ­
ed on a nd off i mmedi ately w hen a tim er is
se t.
,....,
N
0 > co ,...., :=: l) Not avai lab le in all In fota inment system s.
e-tron
Setting the timer in the MMI1l
Applies to vehicles: wit h pl ug-in hybr id drive
Fig. 1 13 MM I: set tin g t he tim er
B y se ttin g th e de parture time, you de ter mine
whe n your veh icle should re ach the des ire d t em ­
peratu re. You can set
a ti me r using the aux iliary
cl imate control o r a uxiliary heat ing/ air condi­
tion ing * menu.
Auxiliary climate control: setting the timer • Sele ct: !ME NUI button> Car> Car Systems >
Aux . climate control > Program timer > Timer
1: Departure time .
• Set the t ime and the date .
• Press the
I BACK! button .
• Confi rm the setting with the cont rol knob to ac­
tivate the time r. A ./
¢ page 123, fig . 112 ap­
pea rs in the box .
Auxiliary heating / air conditioning* : setting
the timer
• Select: !M EN UI button> Car> Car Systems >
Auxiliary heating/ air conditioning
> Program
timer > Timer 1: Departure time .
• Se t the t ime and the da te .
• Press the
I BACK I button.
• Confir m the settin g wit h th e co ntro l kn ob to ac­
t iv at e the time r. A ./
¢page 12 3, fig . 11 2 ap ­
pea rs in the box .
A ft er the depa rtur e tim e is reac he d, t he nex t cal ­
end ar d ay is au tom atic ally en te red in th e
MMI.
To activate the a uxiliary climate cont rol or auxi li­
ary heating/ ai r con ditionin g* for t he next day,
co nfirm the sett ing( ./ in the
MMI ¢ page 123,
fig. 112). ..
123

e-tron
(D Tips
-You can set the timer a maximum of 7 days
in advance.
- You can operate the climate control in the
vehicle interior when the high-voltage bat­
tery is charging using the charging timer
c>page 116.
-Make sure the time and date match in the
MMI settings so that the timer can function
properly. Refer to the MMI Operating Man­
ual for setting the date and time.
- The auxiliary heating or auxiliary heating/
air conditioning* can run longer after the
departure time is reached.
Audi connect e-tron
services
General information
A pp lies to ve hicles : w ith plug- in hy brid drive
With Audi connect e-tron services l), you can ac­
cess various information or control individual
functions remotely using mobile devices (such as
a smartphone) or a web portal.
To use Audi connect e-tron services
l), please
note the following:
- You will need to register for Audi connect e­
tron services at
myaudiconnect .com. You can
access and manage e-tron services and features
at
etron.audiusa.com. If you need assistance
with your Audi A3 e-tron EV services, you can
contact customer service at 844-573-8766.
- Your mobile devices must be compatible.
A WARNING
Read and follow the safety precautions in
your MMI Operating Manual.
l) Wireless serv ice is provided by a thir d- part y provider.
-
Please contact your dea le r or call 877 -505 -2834 for more
informat ion about your carrier. Co nnected dev ices may
not be 4G -capab le. Full speeds avai lable but may be
slowed due to excessive usage, locatio n, coverage and
othe r factors. Coverage not available everyw here . See cov­
erage map for your Audi co nnect data carrier for more in­
format ion.
124
· Vehicle data
App lies to vehicles : wi th plug-i n hybrid drive
The Dr iver Information System collects data un­
der certain conditions and sends it to a server.
When data is stored, you can data such as the ex­
amples listed below using the Audi connect e­
tron services:
- Duration of the drive in hours and minutes,
- average speed driven in mph (km/h),
- distance driven in miles (km),
- average electric consumption .
For additional information on the Driver Informa­
tion System, refer to
c> page 28, Driver informa­
tion system.
Doors and lights
App lies to v ehicl es: wi th plug-in hybrid drive
You can access and display the current status of
the following vehicle data on your mobile devices
without having to be inside the vehicle.
- If the vehicle doors and lids are open/closed,
- If the parking l ights are on/off.
For additional information on opening and clos­
i ng the doors or for the vehicle light ing, refer to
c> page 3 5, Opening and closing or to c> page 46,
Exterior lighting.
(D Tips
-If the high-voltage battery is not charged,
the amount of access requests is limited to
15 after switching off the ignition. This
helps conserve the 12 volt vehicle battery.
You cannot contro l functions or access in­
formation if the charge level of the 12 volt
vehicle battery is too low.
- If at least two minutes have passed after
the last time the ignition was switched off,