2016 AUDI A3 CABRIOLET height

Seats and storage
Important information
A WARNING
Refer to the chapter Driving Safely
~ page 124, Driving safety for important in­
formation , tips, s uggestions and warnings
that you should read and follow for your own
safety and the safety of your passenge rs.
Front seats
Manual seat adjustment
Applies to vehicles with manual adjustable seats
Fig. 53 Fro nt seat: manual seat adj ustment
~ 0 0 > (X) a,
@ -Moving the seat fo rwa rd/back: pu ll the leve r
and slide the seat .
@-Lengthen ing/shortening the upper thigh
support* : lift the handle.
@-Adjusting the angle of the seat surface*.
Pull/press the lever .
@-Adjusting the lumbar support* : press the
button in the desired direction .
®-Moving the seat up/down: pull/press the lev­
er .
@ -Adjusting the backrest angle: turn the ad­
just ing wheel.
A WARNING
- Only adjust the front seat with when the ve-
hicle is stationary . Otherwise, this increases
;;§ the risk of an accident .....
~ -Exercise caution when adjusting the seat N
8 height . Adjusting the seat carelessly or r--. > 00
Seats and storag e
without checking can pinch hands and fin­
gers.
- The front seat backrests must not be re­
clined too far back when driving, because
this impairs the effectiveness of the safety
belts and airbag system, which increases
the risk of injury .
- To reduce the risk of injury during sudden
braking or in a coll is ion, the driver and front
passenger should not have their backrests in
the reclined position whi le dr iving or riding.
The safety be lts and airbag system can pro­
vide the greatest protection possib le when
the backrests a re in the up right posit ion and
the safety belts are worn correctly. The
more a backrest is reclined, the greater the
risk of injury due to an incorrect seating po ­
sition and safety belt position.
Power seat adjustment
Applies to veh icles wit h powe r adjustab le seats
Fig. 54 Froht se at : power seat ad ju stment
@ -Adjust ing the lumbar support: press the but­
ton in the applicable position.
® -moving the seat up/down: press the button
up/down . To adjust the front seat cushion, press
the front button up/down. To adj ust the rear seat
cushion, press the rear button up/down.
® -moving the seat forward/back : press the
button forward/back.
© -adjust ing the backrest ang le: turn the ad­
just ing wheel.
@ -lengthening/shortening the upper thigh sup-
port* : lift the grip handle . .,_
53

Sea ts and stor age
_& WARNING
- Only adjust the front seat with when the ve ­
hicle is stationary. Otherwise, this increases
the risk of an accident
- The power adjustment for the front seats al­
so works wit h the ignition switched off or
with the ignition key removed. For this rea­
son, children shou ld never be left unattend­
ed in the veh icle - they could be injured!
- Exercise caution when adjusting the seat height. Unsuperv ised or careless seat ad­
justment can p inch f ingers or hands causing
injuries.
- The front seat backrests must not be re­
clined too far back when driving, because
this impairs the effectiveness of the safety belts and airbag system, which increases
the risk of injury.
- To reduce the risk of injury during sudden
bra king or i n a co llision, the driver and front
p as senge r shou ld no t have the ir back rests in
the reclined posit ion while driv ing or riding.
T he safety belts and airbag system can pro ­
vide the greatest protection possible when
the backrests are in the upr ight position and
the safety be lts a re worn correctly. The
more a backrest is reclined, the greater the
risk of injury due to an incorrect seating po­
sit ion and safety belt position.
Easy seat entry
Easy seat entry makes it easier to get into the
back seats.
F ig. 55 Driver's seat: easy seat entry cont rols
54
C0 ID
F ig. 56 Easy seat entry operat io n, seat returning to the
or igi nal position w ith seat memory
Folding the front s eat backres ts forward
.. Pull the handle (D ¢ fig. 55 forward.
.. Fold the backrest forward unti l it locks into
place and then slide the seat a ll the way for­
ward using the backrest @.
Fold ing the front seat back rests back
.. Slide the seat all the way back using the back­
rest @¢
fig. 56 .
.. Fold the backrest back until it locks into
place @.
The seat will return to its original posit ion after
u sing easy seat entry.
A WARNING
:;; N 0
> 00 ID
-The front seat backrests must a lways be
l ocked in lace wh ile driving for safety reasons.
- When using easy seat entry, t he seat must
always slide all the way back when returning
it to its orig inal position. Otherwise, the set
w ill not be ab le to lock in place. Only drive
once the seat is locked into place.
{D Tips
If the seat w ill not lock in place after using
easy seat entry, slide the seat all the way back unt il it stops. Then adjust the seat to the de­
sired posit ion.

<( co ..... N
" N ..... 0 r--. > 00
Front center armrest
Applies to vehicles with a front center armrest
The center armrest can be adjusted to several
levels.
Fig . 57 Armrest between the driver's/front passenger's
seats.
,. To adjust the angle, raise the armrest c> fig. 57
notch by notch.
"To bring the armrest back down, raise it out of
the top notch and fold it back down. Then lift
the armrest to the desired position, if necessa­
ry.
The armrest can slide forward and back.
There is a storage compartment under the arm­
rest.
Head restraints
Front head restraints
Applies to: vehicles with ad justab le head restra ints
Fig. 58 Front seat: adjusting the head restraint
~ 0 0 >
l8
Applies to vehicles with super sport seats*: the
head restraint is integrated in the backrest and is
therefore not adjustable
Adjust the head restraints so the upper edge is as
even as possible with the top of your head. If that
Seats and storage
is not possible, try to adjust as close to this posi­
tion as possible .
,. To move the head restraint up or down, slide it
until it locks into place
c> fig. 58.
Refer to c> page 127, Proper adjustment of head
restraints
for gu idelines on how to adjust the
height of the front head restraints to suit the oc­
cupant 's body size.
WARNING
- Driving without head restraints or head re­
straints that are not adjusted correctly dra­
matically increases the risk of serious or fa­
tal neck injuries.
- Read and following the WARNINGS in
c> page 127, Proper adjustment of head re­
straints.
(I} Tips
Head restraints that are adjusted correctly
and safety belts are an extremely effective
combination of safety equipment.
Rear head restraints
Fig. 59 Outer rear head restraints: release point
If there are passengers in the rear seat, fold the
head restraints up on the occupied seats at least
to the next notch
c> .&,.
Adjusting the head restraints
,. To move the head restraint up, hold it at the
sides with both hands and slide it upward until
you feel it click into place.
,. To move the head restraint down, press the
button @
c> fig. 59 and slide the head restraint
downward . .,..
55

<( co ..... N
" N ..... 0 r--. > 00
.. Make sure that nothing can interfere with the
pedals.
.. Adjust front seat , head restraint and mirrors
correctly for your height.
.. Instruct passengers to adjust the head re­
straints accord ing to their height .
.. Make sure to use the right ch ild restraint cor­
rectly to protect children
~ page 165, Child
safety .
.,. Sit properly in your seat and make sure that
your passengers do the same
¢page 53, Front
seats .
.. Fasten your safety be lt and wear it properly. Al­
so instruct your passengers to fasten their safe­
ty belts properly ¢
page 135 .
What impairs driving safety?
Safe driving is directly related to the condition of
the vehicle , the driver as well as the driver's abili­
ty to concentrate on the road without being dis­
tracted.
The driver is responsible for the safety of the ve­
hicle and all of its occupants. If your ability to
drive is impaired, safety risks for everybody in the
veh icle increase and you also become a hazard to
everyone else on the road
¢ ,&. Therefore :
.,. Do not let yourself be distracted by passengers
or by using a cellular telephone.
.. NEVER dr ive when your driv ing ability is im ­
paired (by medications, alcohol, drugs, etc.) .
.. Observe all traffic laws, rules of the road and
speed limits and plain common sense.
.. ALWAYS adjust your speed to road, traffic and
weathe r conditions.
.. Take frequent breaks on long trips. Do not drive
for more than two hours at a stretch .
.. Do NOT drive when you are tired, under pres­
sure or when you are stressed.
A WARNING
Impaired dr iv ing safety increases the risk of
ser ious personal inj ury and death whenever a
vehicle is being used.
Driving safety
Correct passenger
seating positions
Proper seating position for the driver
The proper driver seating position is important
for safe, relaxed driving .
Fig. 120 Correct seating pos it ion
For your own safety and to reduce the risk of in­
jury in the event of an accident, we recommend
that you adjust the driver 's seat to the following
position:
.. Adjust the driver's seat so that you can easily
push the pedals all the way to the floor while
keep ing your knee(s) slightly bent¢,& .
.,. Adjust the angle of the seatback so that it is in
an upright position so that your back comes in
full contact wi th it when you dr ive .
.. Adjust the steering wheel so that there is a dis­
tance of at least 10 inches (25 cm) between the
steering whee l and your breast bone¢
fig. 120.
If not poss ible, see your author ized A udi deal­
ership about adaptive equipment.
.. Adjust the steering wheel so that the steering
wheel and airbag cover points at your chest and
not at your face .
.,. Grasp the top of the steering wheel with your
elbow(s) slightly bent .
.. For adjustable head restraints: Adjust the head
restraint so the upper edge is as even as possi­
b le with the top of your head. If that is not pos­
sible, try to adjust the head restraint so that it
is as close to this posit ion as possible. Move the
head restraint so that it is as close to the back
of the head as possible.
.. Fasten and wear safety belts correctly
¢page 138. ..,.
125

<( co .... N ,.__
N .... 0 ,.__
> co
(D Tires for passenger vehicles
(if applicable)
P indicates a tire for a passenger
vehicle. T indicates a tire desig­
nated for temporary use.
@ Nominal width
Nominal width of the tire be­
tween the sidewalls in millime­
ters. In general: the larger the number, the wider the tire.
@ Aspect ratio
Height/width ratio expressed as a
percentage.
@ Tire construction
R indicates a radial tire.
® Rim diameter
Size of the rim diameter in inches.
@ Load index and speed rating
The load index indicates the tire's load-carrying capacity.
The speed rating indicates the maximum permitted speed¢.&
in
Winter tires on page 219.
"EXTRA LOAD", "xl" or "RF" indi­
cates that the tire is reinforced or
is an Extra Load tire.
Speed rat- Maximum permitted speed
ing
p
up to 93 mph (150 km/h)
Q up to 99 mph (160 km/h)
Tires and wheels
Speed rat- Maximum permitted speed
ing
R up to 1 06 m ph (170 km/h)
s up to 110 mph (180 km/h)
T up to 118 mph (190 km/h)
u up to 124 mph (200 km/h)
H up to 130 mph (210 km /h)
V up to 149 mph (240 km/h)al
z above 149 mph (240 km/h)al
w up to 168 mph (270 km/h)al
y up to 186 mph (300 km/h)al
a ) Tire manufacturers sometimes use "ZR"
for tires with a maximum speed above
149 mph (240 km/h).
(j) US DOT number (TIN) and
manufacture date
The manufacture date is listed on
the tire sidewall (it may only ap­
pear on the inner side of the tire):
DOT ... 2215 ...
means, for example, that the tire
was produced in the 22nd week of
the year 2015.
@ Audi Original equipment
tires
Audi Original equipment tires
with the designation "AO" or "RO"
have been specially matched to
your Audi. When used correctly,
these tires meet the highest standards of safety and handling.
An authorized Audi dealer or au­
thorized Audi Service Facility will ""
205

Tires and wheels
be happy to provide more infor­
mation .
® Mud and snow capability
"M/S" or "M+S" indicates the tire
is suitable for driving on mud and
snow.
& indicates a winter tire.
@ Compos ition of the tire cord
and materials
The number of plies indicates the
number of rubberized fabric lay­
ers in the tire . In general: the
more layers, the more weight a
tire can carry. Tire manufacturers
must also specify the materia ls
used in the tire. These include
steel , nylon, polyester and other
materials.
@ Ma ximum permitted load
T his number indicates the maxi­
mum load in kilograms and
pounds that the tire can carry.
@ Uniform tire quality grade
standards for treadwear,
traction and temperature resistance
Tread wear, t raction and temper­
ature ranges
¢page 221 .
@ Running direction
The arrows indicate the running
direction of unidirectional t ires.
You must always follow the speci -
206
fied running direction
¢page 238 .
(8) Maximum permitted
inflation pressure
This number indicates the maxi­
mum pressure to which a t ire can
be inflated under normal operat­
ing condit ions.
Glossary of tire and loading
terminology
Accessory we ight
means the combined weigh t (in
excess of those standard items
which may be replaced) of auto­ matic transmission, power steer­
ing, power brakes, power win­
dows, power seats , radio, and
heater, to the extent that these
items are available as factory -in ­
stalled equipment (whether in­
stalled or not).
Aspect ratio
means the rat io of the height to
the width of the tire in pe rcent.
Numbers of 55 or lower indicate a
low s idewall for imp roved steer­
ing response and better overa ll
handling on dry pavement.

Tires and wheels
"' Check and cor rect the seating of the snow
c h ains if necessa ry after dr iving a few feet. Fo l­
l ow the instructions from the manufacturer .
"' Note the maximum permitted speed when d riv­
i ng with snow chains. Do not exceed 30 mp h
(SO km/h) .
Snow chains not only improve the
driving in win­
ter road conditions, but also the
broking .
Use of snow cha ins is o nly pe rmitted with certain
rim/t ire combinations due to tec hnical reasons .
C hec k with an authorized A udi dealer o r autho r­
i z ed Audi Service Fac ility to see if yo u may use
snow cha ins.
Use
fine-mesh snow chains . They must not add
mo re t han 0.53 inch (13.5 mm) in height, includ­
i n g the chain loc k.
You must remove the c hains when d riving on
roads that are
free of snow . W hen roads a re free
of snow, snow c hains ca n impair handling and
damage the ti res, and the chai ns w ill quickly be
destroyed.
A WARNINC
Us ing inco rrect snow c hains or insta lling snow
c hai ns inco rre ctl y can resul t in loss o f vehicle
c o ntro l, w hich incr ease s th e ris k of an a cci­
d ent .
(D Note
Snow chains can damage th e rims/wheel cov­
ers* i f the cha ins come in to d irect contact
w it h t hem. R emove the w heel c overs* first .
U se coat ed sn ow cha ins.
Low aspect ratio tires
Your Au di is fac to ry-equipped wi th low aspec t ra­
tio tires . These ti res have been tho roughly tested
a nd been se lected specifically fo r yo ur model fo r
their supe rb per fo rmance, road feel and handling
un der a variety of driving conditions . As k yo ur au­
thor ized Audi dealer for mo re details.
The low aspect ratio of these t ires is i ndicated by
a numeral of
55 or less in t he tire's size designa­
tion. The nume ra l rep resents the rat io of the
tire's sidewall he ight i n relat io n to its tread width
220
exp ressed in perce nta ge . Conventiona l tir es h ave
a height/width ratio of 60 or more.
The performance of low-aspect -ratio tires is par­
ticularly sensitive to improper inflation pres­
sure. It is therefore important that low aspect ratio tires are inflated to the specified pressure
and that the inflation pressure is regularly
checked and maintained. Tire pressures should
be checked at least once a month and always
before a long trip
r=> pog e 214.
What you can do to avoid tire and rim
damage
Low aspect ratio tires can be damaged more eas i­
l y by impact with potho les, curbs, gullies or
r idges on the road, particularly if the tire is un ­
der inflated .
In orde r to min imize the occur rence of impact
damage to the tires of you r vehicle, we recom­
mend that you observe the following preca u­
tions:
- Always ma intain recommended inflation pres­
sures. Check you r tir e pressure every
2,000 miles (3,000 km) and add a ir if necessa­
ry.
- Dr ive ca refully on roads w it h potholes, deep
gu llies o r ridges . Th e impac t from dr iv ing
t hroug h or over such o bstacl es ca n da mage
your tire s. I mpac t w ith a curb may also cau se
d am age to yo ur ti re s.
- After any impac t, imme diate ly inspect you r
t ire s or h ave them inspe cted by t he nea rest a u­
t hori ze d Audi d ealer. Repl ace a dama ged t ire as
soon as possible.
- Ins pect your tir es eve ry 2,00 0 m iles (3,0 00 k m)
for dama ge and wear. Dam age is no t always
easy to see . Damage can lead to loss of a ir and
unde rinflation, w hich coul d event ua lly cause
tire fa ilure. If yo u be lieve that a tire may have
been damaged, replace the tire as soon as pos­
sible .
- These tires may wear mo re quick ly than others.
- Please also remember that, while t hese tires
delive r responsive hand ling, they may ride less
comfortably and make mo re noise than other
choices. ""

<( co .... N ,.__
N .... 0 ,.__
> co
~ Align the jack so that its arm@¢ fig. 183 en­
gages in the designated lifting point in the door
s ill and the movable base ® lies flat on the
ground. The base ® must be
vertical under the
lifting po int @ .
~ Wind the jack up further until the flat tire
comes off the ground ¢
,&.
Position the veh icle jack on ly under the designat­
ed lifting points on the sill¢
fig. 182 . There is ex­
actly
one locat ion for each wheel. The jack must
not be positioned at any other location ¢ _8. ¢(D .
An
u nstable surface under the jack can cause the
ve hicle to slip off the jack . Always provide a firm
base for the jack on the ground. If necessary
place a sturdy boa rd or sim ilar support under the
jack . On
hard, sli ppery surfac es (such as tiles)
use a rubbe r mat o r similar to prevent the j ack
from sli pping ¢.&. .
& WARNING
-
-Yo u or your passengers could be injured
whi le changing a wheel if you do not follow
these safety precautions :
- Position the veh icle jack only at the desig­
nated lifting points and align the jack .
Othe rw ise, the vehicle jac k c ou ld slip and
cause an injury if it does no t have suffi­
cient hold on the vehicle.
- A soft or unstable s urface unde r the jack
may cause the vehicle to slip off the jac k.
Always p rovide a firm base for the jack on
the ground . If necessary, use a sturdy
board under the jack .
- On hard, s lippery surface (such as tiles)
use a rubber mat or similar to prevent the
jack from slipp ing.
- On ly raise your vehicle with the vehicle
jack provided by the factory. If you use a veh icle jack for another vehicle, your vehi­
cle can slide and cause injury.
- Changes in temperature or load can affect
the height of the veh icle.
- Never start the engine when the vehicle is
raised, which co uld cause an accident.
- Support the vehicle securely with appro ­
p riate stands if work is to be performed
Em ergenc y ass is tanc e
underneath the vehicle; otherwise, there
is a potential risk for injury.
- To help prevent injury to yourse lf and your
passengers:
- Do not raise t he vehicle until you are sure
the jack is securely engaged.
- Passengers m ust not remain in the vehicle
when it is jacked up .
- Make sure that passengers wa it in a safe
place away from the vehicle and well away
from the road and traffic.
- Make sure jack position is correct, adjust
as necessary and then continue to raise
t h e jack.
- Changes in temperatu re or load can affect
the height of the veh icle.
(D Note
Do not lift the vehicle by the s ill. Pos it ion the
vehicle jack only at the des ignated lift ing
po ints on the sill. Ot herw ise, your veh icle w ill
be damaged.
237