2016 AUDI A3 CABRIOLET flat tire

Emerg ency assis ta nce
Emergency assistance
Trunk escape latch
Applies to: vehicles with trunk escape latch (A3 sedan)
In case of an emergency, the rear lid can be
opened from the inside using the trunk escape
latch.
Fig. 172 luggage compartment: t runk escape latch
.,. Push the latch in the direction of the arrow un­
til the lock releases .
The trunk escape latch inside the rear lid is made of fluo rescent mater ial to glow in the dark.
_& WARNING
The trunk escape latch is to be used only in an
emergency .
General information
.,. Park the vehicle as far as poss ible from moving
traff ic in the event of a flat tire. In the event of
a flat t ire, park the vehicle on a level surface. It
you are on a steep incline, be especia lly careful.
.,. Set the park ing brake.
.,. Place the selector lever in the P position.
.,. Switch the emergency flashers on.
.,. Put on a reflective vest, if available .
.,. Set up the warning triangle, if available .
.,. Have the passengers exit the vehicle . They
should move to a safe place, for example be­
hind a guard rail.
_& WARNING
Pay attention to the steps above. They are for
your protection and the for the safety of other
drivers.
2 30
Equipment
Vehicle tool kit
Applies to: vehicles with vehicle tool kit
Fig. 173 lu gg age compartmen t: cargo floor cove r fo lded
upward (example)
The vehicle tool kit, t ire repa ir set* and compres­
sor* are stored in the luggage compartment un­
der the floor cover~
fig. 173 .
.,. Hook the p lastic hook@ into the luggage com­
partment seal.
.,. Unhook the cargo floor before closing the lug­
gage compartment lid.
_& WARNING
Improper use of the vehicle jack can cause se­
rious personal injuries.
- Never use the screw driver hex head to
tighten wheel bolts, since the bolts cannot
attain the necessary tightening torque if you
use the hex head, potentially causing an ac­
cident.
- The factory-supplied jack is intended only
for your veh icle model. Under no circum­
stances should it be used to lift heavy
vehicles or other loads; you risk injuring
yourself .
- Never start the engine when the veh icle is
raised, which co uld cause an accident .
- Support the vehicle securely with a ppropri ­
ate stands if work is to be pe rformed under­
neath the vehicle; otherwise, there is a po­
tential risk for injury.
- Never use the jack supplied with your Audi
on another vehicle, particularly on a heavier
one. The jack is only su itable for use on the
vehicle it came with. ..,.

Emergency assistance
Repairing tires
Applies to: vehicles with tire mobility kit
Fig. 175 Components of the tire mobility kit
F ig. 176 Tire mobility k it connecti on
Requirement: the tire mobility kit must be laid
out and ready for use
o page 230, Vehicle tool
kit .
Installing the tire mobility kit
• Open the cover @on the compressor
9fig. 175.
• Remove the connector @) and pressure hose®
with pressure gauge from the housing.
• Install the compressor pressure hose® onto
the flange @ of tire sealant bottle@.
• Insert the sealant bottle with the flange at the
bottom into the opening @ on the compresso r
cover .
... Remove the valve cap from the fau lty tire.
• Install the filler hose @onto the valve
0
ofig. 176.
• Connect the plug @o fig. 175 to a socket in
the vehicle.
• Switch on the ignition.
Inflating a tire
... Move the switch @ o fig. 176 on the compres­
sor into posit ion I.
232
... Inflate the tire to between 29 psi (200 kPA)
and 36 psi (250 kPA) and read the pressure on
the gauge.
• If this tire pressure is not reached, drive your
vehicle approximate ly 33 ft (10 meters) for­
ward or backward so that the sealant can be re­
distr ibuted inside the tire .
.&_ WARNING
- Read and follow the manufacturer's safety
precautions on the compressor and in the
instructions on the bottle of sealant .
-If a tire pressure of 29 psi (200 kPA) cannot
rea ched after inflati ng for 6 minutes, then
the tire is too severely damaged. Do not
continue driving.
- If the tire cannot be repaired with the tire
sealant, see an authorized Audi dealer or au­
thorized Audi Service Facility for assistance.
(D Tips
Do not operate the compressor for more than
6 minutes continuously, or it can overheat.
Once the compressor has cooled, you can con­
tinue to use it .
Completing
Applies to: vehicles with tire mobility kit
... Adhere the sticker that says "max. SO mph
(max. 80 km/h)" that is provided with the tire
mob ility kit w ith in the driver's field of vision.
... Stop the vehicle after driv ing for about 10 mi­
nutes and check the t ire pressure.
• If the tire pressure is lower than 19 psi (130
kPA), then the tire is too severely damaged . Do
not con tinue dr iving. See an authorized Audi
deale r o r authorized Audi Service Facility for as­
sistance.
... If the tire pressure is at least 19 psi (130 kPA),
adjust the tire pressure to the specified value
o page 214, Tire pressure. Store the tire pres­
sures
o page 223, Storing tire pressures. Drive
to the nearest authorized Audi dealer or au­
thorized Audi Service Facility to have the tire re-
placed. ..,.

Emerg enc y assis ta nc e
-If the spare tire is more than 6 years old,
use it only in an emergency and with ex­
treme caution and careful dr iving .
- The spare tire is intended on ly for tempora­
ry and short-term use. It should be replaced
as soon as possible with the normal wheel and t ire .
- After mounting the compact spare t ire, the
t ire pressure must be checked as soon as
poss ible . The tire pressure of the compact
spare tire must be
61 psi (420 kPA); other­
wise, you risk hav ing an accident.
- Do not drive faster than
50 mph (80 km/h).
You risk hav ing an accident.
- Avoid full -throttle accelerat ion, heavy brak­
ing, and fast cornering. You risk having an
acc ident.
- Never dr ive using more than one spare
wheel and tire. You risk having an acc ident .
- Normal summer or winter tires must not be mounted on the compact spare wheel rim.
- For technical reasons, the use of tire chains
on the spare tire is not perm itted. If it is
necessary to drive with t ire chains, the spare
wheel must be mounted on the front axle in
the event of a flat in a rear tire. The new ly
available front wheel m ust then be insta lled
in place of the rear wheel with the flat tire.
Installing the tire chain before mounting
the wheel and tire is recommended.
- Loose items in the passenger compartment
can cause serious personal injury during
hard braking or in an accident. Never store
the inflatable spare t ire or jack and too ls in
the passenger compartment.
- Normal summer or winter tires must not be
mounted on the compact spare wheel rim.
Replacing wheels
Before changing a wheel
Observe the following precautions for your own
and your passenger's safety when changing a
wheel.
.,. After you experience a tire failure, pull the car
well away from moving traff ic and try to reach
le vel ground before you stop¢_& .
234
.. All passengers should lea ve th e car and move
to a safe location (for instance, behind the
guardrail) ¢ _& .
.. Engage the
par king br ake to prevent your vehi­
cle from rolling unintentionally¢_& .
.. Move
selec tor le ve r to p osition P ¢ _& .
.. If you are towing a tra iler , u nhitch the trailer
from your vehicle.
.. Ta ke the
jac k¢ page 230 and the spar e tir e
¢ page 233 out of the luggage compa rtment.
A WARNING
-
You or your passengers could be injured while
changing a whee l if you do not follow these
safety precautions:
- If you have a flat tire, move a safe distance off the road. Turn off the engine, turn the
emergency f lashers on and use other warn­
ing dev ices to alert other motorists.
- Make sure that passengers wait in a safe
place away from the vehicle and well away
from the road and traff ic.
- To help prevent the veh icle from moving
suddenly and possibly slipping off the jack,
always fully set the parking brake and block
the wheel diagonally opposite the wheel be ­
ing cha nged . When one front wheel is lifted
off the ground, placing the Automat ic
T ransmiss ion in P (Park) will
not prevent the
veh icle from moving.
- Before you change a whee l, be sure the
gro und is level and firm . If necessary, use a
sturdy board under the jack.
- Always sto re the vehicle too l kit, the jack
and the replaced tire in the luggage com­
par tment
¢page 130.
Changing a wheel
When you change a wheel, follow the sequence
described below step-by-step and in exactly that
order.
1. Remove the decorati ve wh eel co ver* . For
more detai ls see also ¢
page 235, Decora ­
tive wheel covers
or ¢ page 235, Wheels
with wheel bolt caps .
2. Loosen the wh ee l bolt s ¢page 236.

<( co ..... N
" N ..... 0 r--. > 00
3. Locate the proper mounting point for the
jack and align the jack below that poin t
¢page 236.
4. Raise the car with the jack¢ page 236.
5. Remove the wheel with the flat tire and then
install
the spare ¢ page 238.
6. Tighten all wheel bolts lightly.
7. Lower the veh icle with the jack.
8. Use the wheel bolt wrench and firmly tighten
all wheel bolts
¢page 236 .
9. Replace the decorative wheel cover* .
_& WARNING
Always read and follow all WARNINGS and in­
formation
¢ .&. in Raising the vehicle on
page
237 and ¢ page 239.
After changing a wheel
A wheel change is not complete without the do­
ing the following .
.,. Always store the vehicle tool kit, the jack* and
the replaced tire in the luggage compartment
¢ page 130.
.,. Check the tire pressure on the spar e wheel im­
mediate ly after mount ing it .
.,. As soon as possible, have the
tightening tor­
ques
on all wheel bolts checked with a torque
wrench . The correct tightening torque is
90 ft
lb
(120 Nm) .
.,. Have the flat tire
replaced as soon as possible .
(D Tips
-If you notice that the wheel bolts are cor­
ro ded and difficult to turn while changing a
tire , they should be replaced before you
check the tightening torque .
- Drive at reduced speed until you have the
tightening torques checked.
-Af ter changing a wheel, the tire pressure in
all four tires must be checked/corrected and
the tire pressure monitoring indicator must
be stored in the MMI
9page 223.
Emergency assistance
Decorative wheel covers
Applies to: vehicles with decorative wheel covers
The decorative wheel covers must be removed
first to access the wheel bolts .
Fig. 179 Changing a whe el: Removin g the wh eel cov er
Removing
.,. Insert the hook (provided w ith the vehicle tool
kit) in the hole in the wheel hub cover.
.,. Pull off the
decorative wheel cover¢ fig. 179.
Wheels with wheel bolt caps
Applies to: vehicles with wheel bolts w,th caps
The caps must be removed first from the wheel
bolts before the bolts can be unscrewed.
Fig. 180 Chang ing a whee l: removing th e whee l bol t cap s
Removing
.,. Push the plastic clip (provided with the vehicle
tool kit) over the wheel bolt cap until the inne r
reta iners on the clip align with the edge of the
cover.
.,. Remove the cap with the
plastic clip (vehicle
tool kit)
¢ fig. 180.
Refitting
.,. Place t he caps over the wheel bolts and push
t hem back on.
235

<( co .... N ,.__
N .... 0 ,.__
> co
~ Align the jack so that its arm@¢ fig. 183 en­
gages in the designated lifting point in the door
s ill and the movable base ® lies flat on the
ground. The base ® must be
vertical under the
lifting po int @ .
~ Wind the jack up further until the flat tire
comes off the ground ¢
,&.
Position the veh icle jack on ly under the designat­
ed lifting points on the sill¢
fig. 182 . There is ex­
actly
one locat ion for each wheel. The jack must
not be positioned at any other location ¢ _8. ¢(D .
An
u nstable surface under the jack can cause the
ve hicle to slip off the jack . Always provide a firm
base for the jack on the ground. If necessary
place a sturdy boa rd or sim ilar support under the
jack . On
hard, sli ppery surfac es (such as tiles)
use a rubbe r mat o r similar to prevent the j ack
from sli pping ¢.&. .
& WARNING
-
-Yo u or your passengers could be injured
whi le changing a wheel if you do not follow
these safety precautions :
- Position the veh icle jack only at the desig­
nated lifting points and align the jack .
Othe rw ise, the vehicle jac k c ou ld slip and
cause an injury if it does no t have suffi­
cient hold on the vehicle.
- A soft or unstable s urface unde r the jack
may cause the vehicle to slip off the jac k.
Always p rovide a firm base for the jack on
the ground . If necessary, use a sturdy
board under the jack .
- On hard, s lippery surface (such as tiles)
use a rubber mat or similar to prevent the
jack from slipp ing.
- On ly raise your vehicle with the vehicle
jack provided by the factory. If you use a veh icle jack for another vehicle, your vehi­
cle can slide and cause injury.
- Changes in temperature or load can affect
the height of the veh icle.
- Never start the engine when the vehicle is
raised, which co uld cause an accident.
- Support the vehicle securely with appro ­
p riate stands if work is to be performed
Em ergenc y ass is tanc e
underneath the vehicle; otherwise, there
is a potential risk for injury.
- To help prevent injury to yourse lf and your
passengers:
- Do not raise t he vehicle until you are sure
the jack is securely engaged.
- Passengers m ust not remain in the vehicle
when it is jacked up .
- Make sure that passengers wa it in a safe
place away from the vehicle and well away
from the road and traffic.
- Make sure jack position is correct, adjust
as necessary and then continue to raise
t h e jack.
- Changes in temperatu re or load can affect
the height of the veh icle.
(D Note
Do not lift the vehicle by the s ill. Pos it ion the
vehicle jack only at the des ignated lift ing
po ints on the sill. Ot herw ise, your veh icle w ill
be damaged.
237

<( co .... N r--­N .... 0 r--­> co
-If the spare tire has to be installed in the incor ­
rect direction, use the s pare tire only tempora­
ri ly s ince the tire w ill not be ab le to achieve its
opt imum performance c haracter istics with re ­
gard to aquaplaning, noise and wear .
- We recommend that you pay particular atten­
tion to this fact during wet weathe r and that
yo u ad just yo ur speed to match road condi ­
t io ns.
- Replace t he f lat t ire with a new one and have it
insta lled on yo ur vehicle as soon as possible to
r e store the handling adva ntages of a unid irec­
t io na l t ire .
Notes on wheel changing
Please read the i nfo rma tion ¢ page 211 if y ou
ar e goi ng to use a sp are tir e which i s different
fr om t he tires on yo ur vehicle.
Af ter you ch an ge a tire:
-Check the tire pressure on the spare immedi­
ately after installation.
- Have the wheel bolt tightening torque
checked with a torque wrench as soon as pos­
sible by your authorized Audi dealer or a
qualified service station .
- With steel and alloy wheel rims, the wheel
bolts are correctly tightened at a torque of
90 ft lb (120 Nm) .
- If you notice that the wheel bolts are corroded
and difficult to turn while changing a tire,
they should be replaced before you check the
tightening torque.
- Replace the flat tire with a new one and have
it installed on your vehicle as soon as possi­
ble . Remount the wheel cover.
Until then, drive with extra care and at reduced
speeds .
.8, WARNING
- If you are going to e quip yo ur ve hicl e w ith
tir es or r ims w hic h diff er from t hose whi ch
w ere fa cto ry i nst alled, t hen be s ure t o read
t h e informat ion ¢pa ge
211.
- Alw ays mak e sure the d amag ed whee l or
even a flat tire and t he jack and tool ki t are
-
Emergency assistance
proper ly sec ure d in the l ugga ge compart­
ment a nd a re not loose in the passenger
compa rtm ent.
- In an accident or sudden maneuver they
could fly forward, injuring a nyone in the ve­
h icle.
- A lways sto re damaged wheel, jack and tools
securely in the l uggage compartment. Ot h­
erw ise , in an acc ident or sud den maneuve r
they cou ld fly forwar d, causing injury to pas­
s en ger s in the vehicle .
239