2015 YAMAHA MAJESTY S 125 reset

INSTRUMENT AND CONTROL FUNCTIONS
3-4
234
5
6
7
8
9
EAUT4210
Fuel gaugeThe fuel gauge indicates the amount of
fuel in the fuel tank. The needle moves
towards “E” (Empty) as the fuel level
decreases. When the needle reaches
the red zone, refuel as soon as possi-
ble.
When the key is turned to “ON”, the fuel
gauge needle will sweep once to test
the electrical circuit.
EAUT4230
Multi-function display
WARNING
EWA14432
Be sure to stop the vehicle before
making any setting changes to the
multi-function display. Changing
settings while riding can distract the
operator and increase the risk of anaccident.
The multi-function display is equippedwith the following:

a speedometer

an odometer

a tripmeter (which shows the dis-
tance traveled since it was last set
to zero)

an oil change tripmeter (which
shows the distanc
e traveled since
the last engine oil change)

an oil change indicator (which
flashes when the engine oil should
be changed)

a clock
TIPBe sure to turn the key to “ON” before
using the “SELECT” and “RESET” but-tons.
Odometer, tripmeter and oil change
tripmeter modes
Pushing the “SELECT” button switches
the display among the odometer mode
“ODO”, the tripmeter mode “TRIP” and
the oil change tripmeter “OIL
CHANGE” in the following order:
ODO → TRIP → OIL CHANGE →
ODO
1. Fuel gauge
2. Red zone
1
2
1. Select button
2. Reset button
3. Odometer
4. Oil change tripmeter
5. Tripmeter
6. Speedometer
7. Clock
12
3
4
5
67



INSTRUMENT AND CONTROL FUNCTIONS
3-5
1
23
4
5
6
7
8
9
TIPIf the odometer, tripmeter, or oil change
tripmeter indicates “-----”, have a Yama-
ha dealer check the multi-function dis-play.
OdometerTIPFor the U.K.: The odometer and tripme-
ter units can be switched from kilome-
ters to miles by pushing the “SELECT”button for 1 second.
Tripmeter
To reset the tripmeter, select it by push-
ing the “SELECT” button until “TRIP” isdisplayed, and then push the “RESET”
button for 1 second.
Oil change tripmeter
To reset the oil change tripmeter, select
it by pushing the “SELECT” button until
the oil change tripmeter is displayed,
and then push the “RESET” button for
3 seconds.
Push the “SELECT” button again to
start the oil change tripmeter; the dis-
play changes to the ODO mode.
Oil change indicator “OIL
CHANGE”
This indicator flashes at the initial 1000
km (600 mi), then at every 3000 km
(1800 mi) thereafter to indicate that the
engine oil should be changed.
After changing the engine oil, reset the
oil change tripmeter.
If the engine oil is changed before the
oil change indicator flashes (i.e. before
the periodic oil change interval has
been reached), the oil change tripmeter
must be reset after the oil change for
the next periodic oil change to be indi-
cated at the correct time.1. Odometer
1
1. Tripmeter
1
1. Oil change tripmeter
1



INSTRUMENT AND CONTROL FUNCTIONS
3-6
234
5
6
7
8
9
TIPIf the oil change tripmeter is reset be-
fore the initial 1000 km (600 mi), the
next periodic oil change interval will beat every 3000 km (1800 mi) thereafter.
Clock
To set the clock:1. Set the display to “ODO”, thenpress the “RESET” button for at
least three seconds.
2. When the hour digits start flashing, push the “SELECT” button to set
the hours.
3. Push the “RESET” button, and the first minute digit will start flashing.
4. Push the “SELECT” button to set the first minute digit.
5. Push the “RESET” button and the second minute digit will start flash-
ing.
6. Push the “SELECT” button to set the second minute digit.
7. Push the “RESET” button to start the clock.
TIPIf you do not push the “SELECT” or the
“RESET” button within 30 seconds, the
setting of the clock will not be complet-
ed and the display will change to “ODO”mode.
EAU1234H
Handlebar switchesLeft
Right 1. Horn switch “ ”
2. Turn signal switch
3. Pass switch “PASS”
4. Dimmer switch
1. Start switch “ ”
3
21
4
1



PERIODIC MAINTENANCE AND ADJUSTMENT
6-12
2
3
4
567
8
9
their specified torques.
8. Refill with the specified amount of the recommended engine oil, and
then install and tighten the oil filler
cap.
NOTICE
ECA11671

Do not use oils with a diesel
specification of “CD” or oils of a
higher quality than specified. In
addition, do not use oils labeled
“ENERGY CONSERVING II” or
higher.

Be sure no foreign material en-ters the crankcase.
9. Start the engine, and then let it idle for several minutes while checking it for oil leakage. If oil is leaking, im-
mediately turn the engine off and
check for the cause.
10. Turn the engine off, and then check the oil level and correct it if
necessary.
11. Reset the oil change indicator and oil change tripmeter. (See
page 3-4.)
EAU20067
Final transmission oilThe final transmission case must be
checked for oil leakage before each
ride. If any leakage is found, have a
Yamaha dealer check and repair the
scooter. In addition, the final transmis-
sion oil must be changed as follows at
the intervals specified in the periodic
maintenance and lubrication chart.1. Start the engine, warm up the final transmission oil by riding the
scooter for several minutes, and
then stop the engine.
2. Place the scooter on the center- stand.
3. Place an oil pan under the final transmission case to collect the
used oil.
4. Remove the final transmission oil filler cap and its O-ring from the fi-
nal transmission case.
Tightening torque:Engine oil drain bolt A:20 Nm (2.0 m·kgf, 14 ft·lbf)
Engine oil drain bolt B: 32 Nm (3.2 m·kgf, 23.1 ft·lbf)
Recommended engine oil: See page 8-1.
Oil change quantity: 0.95 L (1.00 US qt, 0.84 Imp.qt)