2015 SUZUKI NEXA check engine
[x] Cancel search: check enginePage 232 of 288
Downloaded from www.Manualslib.com manuals search engine , 1 6 3 ( & 7 , 2 1 $ 1 ' 0 $ , 1 7 ( 1 $ 1 & (
0 6 (
7 L J K W H Q L Q J W R U T X H I R U R L O I L O W H U
' $ ' L H V H O H Q J L Q H
1 P N J P O E I W
5 H I L O O Z L W K 2 L O D Q G & K H F N I R U / H D N V1) Pour oil through the filler hole and
install the filler cap.
For the approximate capacity of the oil,
refer to the “Capacities” item in the
“SPECIFICATIONS” section.
2) Start the engine and look carefully for
leaks at the oil filter and drain plug. Run
the engine at various speeds for at least
5 minutes.
3) Stop the engine and wait about 5 min-
utes. Check the oil level again and add
oil if necessary. Check for leaks again.
) R U ' $ $ ' L H V H O ( Q J L Q H 0 R G H OSince spec
ial procedures and tools are
requ
ired,
it is recommended that you trust
this job to your
A U T H O R I S E D - A R U T I
3 U Z U K I W O R K S H O P
( Q J L Q H & R R O D Q W 6 H O H F W L R Q R I & R R O D Q WTo m a
inta
in opt
imum performance and
durab
ility of your eng
ine, use MARUTI
Genu
ine Coolant or equ
ivalent
.
Th
is type of coolant
is best for your cool
ing
system as
it:
• Helps mainta
in proper eng
ine tempera-
ture
.
•G
ives proper protect
ion aga
inst freez
ing
and bo
iling.
•G
ives proper protect
ion aga
inst corro-
s
ion and rust
.
Failure to use the proper coolant can dam-
age your cooling system. Your D X W K R U L V H G
0 D U X W L 6 X ] X N L Z R U N V K R S can help you
select the proper coolant.
NOTICE
7 R S U H Y H Q W R L O O H D N D J H P D N H V X U H
W K D W W K H R L O I L O W H U L V W L J K W E X W G R Q R W
R Y H U W L J K W H Q L W
NOTICE
Page 233 of 288
Downloaded from www.Manualslib.com manuals search engine
, 1 6 3 ( & 7 , 2 1 $ 1 ' 0 $ , 1 7 ( 1 $ 1 & (
0 6 (
& R R O D Q W / H Y H O & K H F NCheck the coolant level at the reservoir
tank, not at the radiator. With the engine
cool, the coolant level should be between
the “FULL” and “LOW” marks. $ G G L Q J & R R O D Q W
61MM0A125
NOTICE
7 R D Y R L G G D P D J L Q J \ R X U F R R O L Q J V \ V
W H P
Page 236 of 288
Downloaded from www.Manualslib.com manuals search engine , 1 6 3 ( & 7 , 2 1 $ 1 ' 0 $ , 1 7 ( 1 $ 1 & (
0 6 (
& O X W F K 3 H G D O ) O X L G & R Q W U R O & O X W F K
64MS141
Check the clutch pedal for smooth opera-
tion and clutch fluid level from time to time.
If clutch dragging is felt with the pedal fully
depressed, have the clutch inspected by
D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S. If the
clutch fluid level is near the “MIN” triangle
mark, fill it up to the “MAX” triangle mark
with MARUTI genuine brake fluid.
) X H O ) L O W H U
64MS175
The fuel filter works as a water sedimentor
as well.
Drain water according to the Periodic
Maintenance Schedule. To drain water:
1) Place a pan or ample rag under the fuel
filter drain nozzle.
2) Loosen the drain screw (1). The water
will be drained.
3) Tighten the drain screw when the water
changes to the diesel fuel.
7 L J K W H Q L Q J W R U T X H I R U G U D L Q V F U H Z
1 P N J P O E I W
% U D N H V % U D N H ) O X L G
64MS141
Check the brake fluid level by looking at
the reservoir in the engine compartment.
Check that the fluid level is between the
“MAX” and “MIN” triangle mark. If the
brake fluid level is near the “MIN” triangle
mark, fill it up to the “MAX” triangle mark
with MARUTI GENUINE BRAKE FLUID.
MAX
MIN
(1)
( ; $ 0 3 / (
MAX
MIN
Page 237 of 288
Downloaded from www.Manualslib.com manuals search engine
, 1 6 3 ( & 7 , 2 1 $ 1 ' 0 $ , 1 7 ( 1 $ 1 & (
0 6 (
NOTE:With disc brakes, the fluid level can be
expected to gradually fall as the brake pads
wear. % U D N H 3 H G D OCheck if the brake pedal stops at the regular
height without spongy feeling when you
depress it. If not, have the brake system
inspected by your D X W K R U L V H G 0 D U X W L 6 X ] X N L
Z R U N V K R S. If you doubt the brake pedal for
the regular height, check it as follows:
54G108
3 H G D O W R I O R R U F D U S H W P L Q L P X P G L V
W D Q F H ³ D ´ P P L Q With the engine running, measure the dis-
tance between the brake pedal and floor
carpet when the pedal is depressed with
approximately 30 kg (66 lbs) of force. The
minimum distance required is as specified.
Since your vehicle’s brake system is self-
adjusting, there is no need for pedal adjust-
ment.
If the pedal to floor carpet distance as mea-
sured above is less than the minimum dis-
tance required, have your vehicle inspected
by your D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S.NOTE:When measuring the distance between the
brake pedal and floor wall, be sure not to
include the floor mat or rubber on the floor
wall in your measurement.
: $ 5 1 , 1 *
) D L O X U H W R I R O O R Z W K H J X L G H O L Q H V E H O R Z
F D Q U H V X O W L Q S H U V R Q D O L Q M X U \ R U V H U L
R X V G D P D J H W R W K H E U D N H V \ V W H P
Page 239 of 288
Downloaded from www.Manualslib.com manuals search engine
, 1 6 3 ( & 7 , 2 1 $ 1 ' 0 $ , 1 7 ( 1 $ 1 & (
0 6 (
7 L U H V
74LHT0704
The front and rear tire pressure specifica-
tions for your vehicle are listed on the Tire
Information Label. Both the front and rear
tires should have the specified tire pressure.
Note that the value does not apply to the
spare tire, if equipped.
7 L U H , Q V S H F W L R QInspect your vehicle’s tires at least once a
month by performing the following checks:1) Measure the tire pressure with a tire
gauge. Adjust the pressure if necessary.
Remember to check the spare tire, too.
54G136
(1) Tread wear indicator
(2) Indicator location mark2) Check that the depth of the tread groove
is more than 1.6 mm (0.06 in.). To help
you check this, the tires have molded-in
tread wear indicators in the grooves.
When the indicators appear on the tread
surface, the remaining depth of the tread
is 1.6 mm (0.06 in.) or less and the tire
should be replaced.
3)Check for abnormal wear, cracks and
damage. Any tires with cracks or other
damage should be replaced. If any tires
show abnormal wear, have them
inspected by your
D X W K R U L V H G 0 D U X W L
6 X ] X N L Z R U N V K R S
.
( ; $ 0 3 / (
: $ 5 1 , 1 *
Page 240 of 288
Downloaded from www.Manualslib.com manuals search engine , 1 6 3 ( & 7 , 2 1 $ 1 ' 0 $ , 1 7 ( 1 $ 1 & (
0 6 (
4) Check for loose wheel nuts.
5) Check that there are no nails, stones or
other objects sticking into the tires.
7 L U H 5 R W D W L R Q W L U H U R W D W L R Q
80JK040
If your vehicle is equipped with a spare tire
which is a different wheel type than the
wheels on the vehicle, you must use a 4-
tire rotation as shown in the example
below.
W L U H U R W D W L R Q
54G114
To avoid uneven wear of your tires and to
prolong their life, rotate the tires as illus-
trated. Tires should be rotated every 10000
km (6000 miles). After rotation, adjust front
and rear tire pressures to the specification
listed on your vehicle’s Tire Information
Label.
& $ 8 7 , 2 1
+ L W W L Q J F X U E V D Q G U X Q Q L Q J R Y H U U R F N V
F D Q G D P D J H W L U H V D Q G D I I H F W Z K H H O
D O L J Q P H Q W % H V X U H W R K D Y H W L U H V D Q G
Z K H H O D O L J Q P H Q W F K H F N H G S H U L R G L
F D O O \ E \ \ R X U D X W K R U L V H G 0 D U X W L
6 X ] X N L Z R U N V K R S
: $ 5 1 , 1 *
Page 241 of 288
Downloaded from www.Manualslib.com manuals search engine 7-18
INSPECTION AND MAINTENANCE
64MS0-74E
Wheel AlignmentIn case of abnormal tyre wear or pull
ing
towards one s
ide, have the wheel al
igned
at
A U T H O R I S E D - A R U T I 3 U Z U K I . % 8 ! D E A L E R
W O R K S H O P
Tubeless Tyres (If equipped)The veh
icle
is equ
ipped w
ith Tubeless
Tyres
. In tubeless tyre, a th
in layer of butyl
rubber
is used for l
ining the
inside of the
tubeless tyre
. Th
is layer
is to prevent a
ir
loss and fulf
illing the purpose of tube
. The
a
ir pressure
is ma
inta
ined by the seal
ing
between tyre bead and wheel r
im. Tube-
less tyres are hav
ing advantage of slow a
ir
loss and prevent
ing sudden deflat
ion wh
ile
dr
iving.Care and maintenance tips for tubeless
tyres
1) Always ma
inta
in recommended
inflat
ion
pressure
. Dr
iving cont
inuously at low
inflat
ion pressure can lead to tyre dam-
age.
2) In case any leakage
is found, check for
any na
il penetrat
ion/valve core dam-
age or r
im bent
. Damaged wheel must
not be used
.
3) In case tyre has run at low pressure,
it
must be
inspected for any defect
.
4) Whenever new tyre
is fitted, replace the
valve
.
5) If cont
inuous h
igh speed dr
iving
is
requ
ired,
increase tyres pressure by 5
ps
i over recommended
inflat
ion pres-
sure
.
6) Never run the tyre beyond TWI (Tread
wear
indicator)
. The tyre
is recommen-
ded to be replaced when the rema
ining
tread has worn to th
is po
int. The
indica-
tors are spaced across the tread
around the tyre marked by a tr
iangular
symbol (TWI)
.
7) Always prefer tubeless tyre mount
ing
mach
ine. In case of manual mount
ing-
tyre/wheel r
im damage may occur
.
8)
In case of any problem, please get
in
touch w
ith
A U T H O R I S E D - A R U T I 3 U Z U K I
W O R K S H O P
Battery
WA R N I N G
• Batteries produce flammable
hydrogen gas. Keep flames and
sparks away from the battery or an
explosion may occur. Never smoke
when working in the vicinity of the
battery.
• When checking or servicing the
battery, disconnect the negative
cable. Be careful not to cause a
short circuit by allowing metal
objects to contact the battery posts
and the vehicle at the same time.
• To avoid harm to yourself or dam-
age to your vehicle or battery, fol-
low the jump starting instructions
in the “EMERGENCY SERVICE”
section of this manual if it is neces-
sary to jump start your vehicle.
• Diluted sulfuric acid spilled from
battery can cause blindness or
severe burns. Use proper eye pro-
tection and gloves. Flush eyes or
body with ample water and get
medical care immediately if suf-
fered. Keep batteries out of the
reach of children.
Wheel BalancingIf the veh
icle v
ibrates abnormally on
smooth road, have the wheel balanced at
A U T H O R I S E D - A R U T I 3 U Z U K I W O R K S H O P
Page 242 of 288
Downloaded from www.Manualslib.com manuals search engine , 1 6 3 ( & 7 , 2 1 $ 1 ' 0 $ , 1 7 ( 1 $ 1 & (
0 6 (
76MS006
7he level of the battery solution must be
kept between the upper level line (1)
and lower level line (2) at all times. If the
level is found to be below the lower level
line (2), add distilled water to the upper
level line (1). You should periodically check
the battery, battery terminals, and battery
hold-down bracket for corrosion. Remove
corrosion using a stiff brush and ammonia
mixed with water, or baking soda mixed
with water. After removing corrosion, rinse
with clean water.
If your vehicle is not going to be driven for
a month or longer, disconnect the cable
from the negative terminal of the battery to
help prevent discharge. 5 H S O D F H P H Q W R I W K H E D W W H U \
) R U ' $ ' L H V H O ( Q J L Q H 0 R G H O
64MS160
NOTE:
(For D13A Diesel Engine Model)
To approach the battery, remove the suc-
tion pipe (1). ) R U ' $ $ ' L H V H O ( Q J L Q H 0 R G H O
61MS2A006
NOTE:
(For D16AA Diesel Engine Model)
To approach the battery, loosen the bolts,
push the locks and remove the suction
pipe (1).
( ; $ 0 3 / (
(1)
( ; $ 0 3 / (
(1)
( ; $ 0 3 / (