2015 SUZUKI NEXA battery
[x] Cancel search: batteryPage 106 of 288
Downloaded from www.Manualslib.com manuals search engine (1)
(2)
2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
2) Without depressing the clutch pedal,
press the engine switch (1).
82K254
Every time you press the engine switch,
the ignition mode changes as follows.
57L31033
NOTE:
When selecting the ignition modes, the
information display in the instrument clus-
ter shows certain messages. Refer to
“Information Display” in the “BEFORE
DRIVING” section for details. , I W K H 0 $ 6 7 ( 5 : $ 5 1 , 1 * L Q G L F D W R U O L J K W
E O L Q N V D Q G W K H L J Q L W L R Q P R G H V F D Q Q R W
E H V H O H F W H G
Your keyless push start system remote con-
troller may not be sensed as being within the
“interior workable area” (refer to the related
explanation in this section). Try again after
making sure you have the remote controller
with you. If the ignition modes still cannot be
selected, the battery of the remote controller
may be discharged. To be able to select an
ignition mode, you must then use the follow-
ing method:
58MST0302
1) Without depressing the brake pedal
and the clutch pedal, push the engine
switch (1).
2) Within about 10 seconds during which
the master warning indicator light in the
instrument cluster is blinking and the
“PLACE KEY FOB ON START
SWITCH” message appears on the
information display, touch the engineswitch with the lock button end of the
remote controller (2) for about 2 sec-
onds.
NOTE:
•
If you still cannot select the ignition
modes, there may be some problem with
the keyless push start system. Contact
an D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S
for an inspection of the system.
• The immobilizer/keyless push start sys-
tem warning light will come on for about
5 seconds while the master warning indi-
cator light is blinking. In addition, the
information display in the instrument
cluster will show a message during this
time. Refer to “Information Display” in
the “BEFORE DRIVING” section for
details.
•
You may customize the system to cause
the interior buzzer to sound once for the
remote controller out of sensing range
warning. To incorporate this customiza-
tion, please contact an D X W K R U L V H G 0 D U X W L
6 X ] X N L Z R U N V K R S
• If the battery of the remote controller is
about to become completely discharged,
the corresponding message will appear
on the information display when you
press the engine switch to change the
ignition mode to ON. Refer to “Informa-
tion Display” in the “BEFORE DRIVING”
section for details. For details on replac-
ing the battery, refer to the “Keyless
Push Start System Remote Controller” in
the “BEFORE DRIVING” section.
(OFF)
ON ACC LOCK
(Audio equipment)
( ; $ 0 3 / (
(1)
Page 107 of 288
Downloaded from www.Manualslib.com manuals search engine
2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
5 H P R W H & R Q W U R O O H U 2 X W V L G H : D U Q L Q JWhen either of the conditions described
below is met, the system issues the remote
controller outside warning by sounding the
interior and exterior buzzers. At the same
time, the immobilizer/keyless push start
system warning light comes on and the
master warning indicator light blinks.
• Any door is opened and then closed
while the remote controller is not inside
the vehicle and the engine is running or
the ignition mode has been changed to
“ACC” or “ON” by pressing the engine
switch.
• The remote controller is not inside the
vehicle when you attempt to start the
engine after changing the ignition mode
to “ACC” or “ON” by pressing the engine
switch.
61MM0A182
(1) Immobilizer/keyless push start sys-
tem warning light (blinks)
(2) Master warning indicator light (blinks)
NOTE:
• If the warning is given, locate the remote
controller as soon as possible.
• Any attempt to start the engine will fail
while the warning is active. The mes-
sage appearing on the information dis-
play in the instrument cluster will also
indicate this condition. Refer to “Informa-
tion display” in the “BEFORE DRIVING”
section for details.
• Normally, the immobilizer/keyless push
start system warning light should go out
and the master warning indicator light
should stop blinking shortly after the
remote controller is brought back inside
the vehicle. If they remain lit and blink-
ing, change the ignition mode to “LOCK”
(OFF) by pressing the engine switch and
then perform the engine starting opera-
tion. Refer to “Starting the Engine” in this
section.
• Always keep the remote controller with
you as the driver.
, Q W H U L R U : R U N D E O H $ U H D I R U ( Q J L Q H
6 W D U W L Q J , J Q L W L R Q 0 R G H 6 H O H F W L R Q
D Q G 5 H P R W H & R Q W U R O O H U 2 X W V L G H
: D U Q L Q J
61MM0B002
(1) Interior workable area
The interior workable area for these func-
tions is defined as all the interior spaces
except for the space above the instrument
panel.
NOTE:
• Even when the remote controller is in the
“interior workable area”, if it is in any of
the following conditions, you may not be
able to start the engine or select the igni-
tion modes, and the remote controller
outside warning may be given.
– The remote controller’s battery is low.
– The remote controller is affected by
strong radio signals or noise.
– The remote controller is in contact with
or covered by a metallic object.
(1)
(2)
(1)
Page 112 of 288
Downloaded from www.Manualslib.com manuals search engine 2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
tion. In this case, always let the engine
idle before stop it. 6 W D U W L Q J D & R O G D Q G : D U P ( Q J L Q H & R O G H Q J L Q H
Depress the clutch and brake pedals fully
and press the engine switch to crank the
engine. If the glow plug indicator light
comes on, the engine will start automati-
cally after the glow plug indicator light goes
off or 10 seconds past.
: D U P H Q J L Q H
Crank the engine by pressing the engine
switch to change the ignition mode to
“START”. & D X W L R Q Z K H Q V W R S S L Q J W K H H Q J L Q H Z L W K
W X U E R F K D U J H U
When stopping the engine after climbing or
high speed driving, let the engine idle for
about one minute or more (if it is not pro-
hibited) to cool down the turbocharger and
engine oil. This is to prevent the engine oil
from over-deteriorating. Deteriorated
engine oil will damage the bearings of the
turbocharger.
5 H V W D U W L Q J G L H V H O H Q J L Q H D I W H U I X H O
H P S W \ V W R S
If the engine stops and the low fuel warn-
ing light and the malfunction indicator light
come on, use the following procedure:
1) Fill the fuel tank.
2) Press the engine switch to change the
ignition mode to “ON” for 5-10 seconds
to feed fuel.
3) Perform above engine starting proce-
dure to start the engine.
If the malfunction indicator light still comes
on after the engine started, there may be
some problem with the engine. Ask your
D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S to have
the engine inspected.
, I W K H 0 $ 6 7 ( 5 : $ 5 1 , 1 * L Q G L F D W R U O L J K W
E O L Q N V D Q G W K H H Q J L Q H F D Q Q R W E H V W D U W H G
Your keyless push start system remote
controller may not be sensed as being
within the interior workable area. Try again
after making sure that you have the remote
controller with you. If the engine still can-
not be started, the battery of the remote
controller may be discharged. You mustthen use the following method to be able to
start the engine.
58MST0302
1) Make sure the parking brake is set fully.
2) Shift to “N” (Neutral) and fully depress
the clutch pedal. Hold the clutch and
brake pedals fully depressed.
3) The “PUSH START SWITCH.” mes-
sage will appear on the information dis-
play in the instrument cluster. Press the
engine switch (1).
4) Within about 10 seconds of blinking of
the “MASTER WARNING” indicator
light in the instrument cluster, touch the
engine switch with the lock button end
of the remote controller (2) for about 2
seconds.
NOTE:
• If you still cannot start the engine after
several attempts using the above
NOTICE
' R Q R W F U D Q N W K H H Q J L Q H I R U P R U H
W K D Q V H F R Q G V D W D W L P H
, I W K H H Q J L Q H G R H V Q
Page 113 of 288
Downloaded from www.Manualslib.com manuals search engine
2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
method, there may be a problem else-
where, such as a low battery. Contact
your D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S
for inspection.
• The immobilizer/keyless push start sys-
tem warning light will come on for about
5 seconds while the master warning indi-
cator light is blinking. In addition, the
information display will show a certain
message during this time. Refer to
“Information Display” in the “BEFORE
DRIVING” section for details.
• You may customize the system to cause
the interior buzzer to sound once for the
remote controller out of sensing range
warning. Please contact an D X W K R U L V H G
0 D U X W L 6 X ] X N L Z R U N V K R S for the
customization.
• If the battery of the remote controller is
about to be completely discharged, a
message warning this will appear on the
information display when the ignition
mode is changed to “ON” by pressing
the engine switch. For details on replac-
ing the battery, refer to the “Keyless
Push Start System Remote Controller” in
the “BEFORE DRIVING” section.
5 H W X U Q L Q J W K H L J Q L W L R Q P R G H W R
³ / 2 & . ´ 2 ) )
Page 145 of 288
Downloaded from www.Manualslib.com manuals search engine
2 7 + ( 5 & 2 1 7 5 2 / 6 $ 1 ' ( 4 8 , 3 0 ( 1 7
0 6 (
) U R Q W Z L W K R X W R Y H U K H D G F R Q V R O H
61MM0A205
Push the switch to turn on the light and
push it again to turn off the light.
) U R Q W Z L W K R Y H U K H D G F R Q V R O H
64MS119
& H Q W H U
61MM0A107
These light switches have three or four
positions with function as described below: 2 1 D
• The light comes on and stays on regard-
less of whether the door is open or
closed.
• To save the battery, the light will be auto-
matically turned off when a period of 15
minutes has elapsed after the light is on.
' 2 2 5 E
• The light comes on when the door is
opened. After closing all doors, the light
will remain on for about 15 seconds and
then fade out. If you insert the key, or
press the engine switch to change the
ignition mode to ACC or ON during this
time, the light will start to fade out imme-
diately. After removing the key from the
ignition switch, the light will turn on for
about 15 seconds and then fade out.
• Regardless of whether the door is open
or closed, the light comes on 15 seconds
and then fade out when the ignition
mode is changed to LOCK (OFF) or the
ignition switch is turned to the “LOCK”
position.
2 ) ) F
The light remains off even when the door is
opened.
6 3 2 7 / , * + 7 G
When the light switch is in the DOOR or
OFF position, push the switch to turn on
the light and push it again to turn off the
light. ( ; $ 0 3 / (
(d) (c) (b) (a) (d)
(a)
(b)
(c)
( ; $ 0 3 / (
Page 191 of 288
Downloaded from www.Manualslib.com manuals search engine
2 7 + ( 5 & 2 1 7 5 2 / 6 $ 1 ' ( 4 8 , 3 0 ( 1 7
0 6 (
NOTE:
If text data contains more than 12 charac-
ters, the “>” mark will appear at the right
end. Holding down the DISP button (7) for
1 second or longer can display the next
page.
3 O D \ L Q J 0 R G H V H O H F W L R Q
1) Press the button numbered [6] of the
Preset buttons (8) for 1 second or lon-
ger.
2) Turn the TUNE FOLDER PUSH
SOUND knob (2).
Each time the knob is turned, the mode
will change as follows:
3) Press the TUNE FOLDER PUSH
SOUND knob (2) to select the desired
mode.
NOTE:
• When the button numbered [6] of the
Preset buttons (8) is pressed, the previ-
ous mode will be displayed.
1 R W H V R Q L 3 R G
Š
6 X S S R U W H G L 3 R G
Š
•iPod
® touch (5th generation)
•iPod® touch (4th generation)
•iPod® touch (3rd generation)
•iPod® touch (2nd generation)
•iPod® touch (1st generation)
•iPod® classic
•iPod® nano (7th generation)
•iPod® nano (6th generation)
•iPod® nano (5th generation)
•iPod® nano (4th generation)
•iPod® nano (3rd generation)
•iPod® nano (2nd generation)
•iPod® nano (1st generation)
•iPod® (5th generation)
•iPod® (6th generation)
•iPod®(6thPlus generation)
•iPhone® 6 / 6 plus
• iPhone® 5
• iPhone® 4S
• iPhone® 4
• iPhone® 3GS
• iPhone® 3G
• iPhone®
* Some functions may not be available
depending on the model of iPod
®.
*iPod
® is a trademark of Apple Inc., regis-
tered in the U.S. and other countries.
*iPhone® is a trademark of Apple Inc.,
registered in the U.S. and other coun-
tries.
* Apple is not responsible for the opera-
tion of this device or its compliance with
safety and regulatory standards. L 3 R G
Š F R Q Q H F W L R Q
• Make sure to detach the iPod
® after
pressing the engine switch to change the
ignition mode to “LOCK” (OFF) or the
ignition switch is turned to the “LOCK”
position. The iPod
® may not be shut
down when it is being connected and
may result in battery depletion.
• Please do not connect iPod
® accesso-
ries such as an iPod
® remote control or
headphones while connecting the iPod
®
with the unit. The unit may not operate
correctly.
PLAYLIST
ARTIST
ALBUM
SONGS
GENRE
Page 208 of 288
Downloaded from www.Manualslib.com manuals search engine 2 7 + ( 5 & 2 1 7 5 2 / 6 $ 1 ' ( 4 8 , 3 0 ( 1 7
0 6 (
The anti-theft function is intended to dis-
courage thefts, such as that the audio sys-
tem becomes inoperable when it is installed
on other vehicles.
This function works by entering a Personal
Identification Number (PIN).
When the unit is disconnected from its
power source, such as when the audio sys-
tem is removed or the battery is discon-
nected, the unit will become inoperable until
the PIN is reentered. 6 H W W L Q J W K H $ Q W L 7 K H I W ) X Q F W L R Q1) Press the VOL PUSH POWER knob (1)
to power off.
2) Hold down the buttons numbered [1]
and [6] of the Preset buttons (2) and
press the VOL PUSH POWER knob (1).
“SECURITY” will be displayed.
3) Press the Up button (3) and the button
numbered [1] of the Preset buttons (2)
simultaneously.
4) Enter a 4-digit number to be registered
as PIN using the buttons numbered [1] -
[4] of the Preset buttons (2).
5) Hold down the TUNE FOLDER PUSH
SOUND knob (4) for 1 second or longer
to set the anti-theft function.NOTE:
Take a note of the registered PIN and keep
it for the future use. & D Q F H O L Q J W K H D Q W L W K H I W I H D W X U H
To cancel the anti-theft function, delete the
registered PIN.
1) Press the VOL PUSH POWER knob
(1) to power off.
2) Hold down the buttons numbered [1]
and [6] of the Preset buttons (2) and
press the VOL PUSH POWER knob
(1).
“PIN ENTRY” will be displayed.
3) Press the Up button (3) and the button
numbered [1] of the Preset buttons (2)
simultaneously.
4) Enter a 4-digit number to be registered
as PIN using the buttons numbered [1] -
[4] of the Preset buttons (2).
5) Hold down the TUNE FOLDER PUSH
SOUND knob (4) for 1 second or lon-
ger to delete the registered PIN. The
indication “----” will be displayed and
the anti-theft function will be canceled.
NOTE:
To change your PIN, first delete your cur-
rent PIN, then set a new one. & R Q I L U P L Q J W K H 3 H U V R Q D O , G H Q W L I L F D W L R Q
1 X P E H U 3 , 1
When the main power source is discon-
nected such as when the battery is
replaced, etc, it is required to enter the PIN
to make the unit operable again.
1) Set the ignition switch to the “ACC”
position.
“SECURITY” will be displayed.
2) Press the Up button (3) and the button
numbered [1] of the Preset buttons (2)
simultaneously.
3) Enter a 4-digit number to be registered
as PIN using the buttons numbered [1] -
[4] of the Preset buttons (2).
4) Hold down TUNE FOLDER PUSH
SOUND knob (4) for 1 second or lon-
ger.
When the PIN same as registered is
entered, the power of the audio system
will be turned off automatically and it
will become operable again.
NOTE:
If an incorrect PIN is entered, “ERROR”
and the total number of incorrect entry
attempts will be displayed.
If an incorrect PIN is entered 10 times or
more, “HELP” will be displayed and the
audio system will become inoperable.
Page 209 of 288
Downloaded from www.Manualslib.com manuals search engine
2 7 + ( 5 & 2 1 7 5 2 / 6 $ 1 ' ( 4 8 , 3 0 ( 1 7
0 6 (
% D W W H U \ , Q V W D O O D W L R QInstall a lithium battery (CR2025) with the poles facing the correct direction.
% D W W H U \ U H S O D F H P H Q W W L P L Q J
• When battery power is depleted, the button may not be operable. If the remote controller
does not operate, replace the battery and check the operation.
& D X W L R Q R Q E D W W H U \
• Be sure to follow the instructions to prevent battery leakage, over-heating, ignition or
explosion.
If battery leakage has occurred, wipe the
container first then install a new battery. If
the battery solution contacts the skin, wash
off with water completely.
& D X W L R Q R Q 5 H P R W H & R Q W U R O O H U• Do not leave the remote controller in an
area exposed to direct sunlight, such as
on the dashboard or steering wheel. The
remote controller may deform because of
the heat, (Be especially careful of the
dashboard exposed to direct sunlight in
the summer, as it will become extremely
hot).
: $ 5 1 , 1 *