2015 SUZUKI NEXA turn signal
[x] Cancel search: turn signalPage 92 of 288
Downloaded from www.Manualslib.com manuals search engine % ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
+ H D G O L J K W / H Y H O L Q J 6 Z L W F K
80JM040
Level the headlight beam according to the
load condition of your vehicle by turning this
switch. The chart below shows the appropri-
ate switch position for different vehicle-load
conditions.
7 X U Q 6 L J Q D O & R Q W U R O / H Y H U
65D611
7 X U Q 6 L J Q D O 2 S H U D W L R QWith the ignition switch in the “ON” position
or the ignition mode ON, move the lever up
or down to activate the right or left turn sig-
nals.
1 R U P D O W X U Q V L J Q D O
60MK013
Move the lever all the way upward or
downward to signal. When the turn is com-
pleted, the signal will cancel and the lever
will return to its normal position.
/ D Q H F K D Q J H V L J Q D O
60MK014
Move the lever part-way in the direction to
turn and hold it there.
Vehicle Load
Condition
Switch PositionD13A
EngineD16AA
Engine
Driver only 0 0Driver +
1 passenger
(in front seat)
00
Driver +
4 passengers,
no cargo
11
Driver +
4 passengers,
cargo added
22
Driver +
full cargo
33
: $ 5 1 , 1 *
7 R D Y R L G S R V V L E O H L Q M X U \ G R Q R W R S H U
D W H F R Q W U R O V E \ U H D F K L Q J W K U R X J K W K H
V W H H U L Q J Z K H H O
( ; $ 0 3 / ( ( ; $ 0 3 / (
Page 93 of 288
Downloaded from www.Manualslib.com manuals search engine
% ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
• The turn signal and its indicator flash
while the lever is held at the moved posi-
tion.
The turn signal and its indicator flash three
times even if you return the lever immedi-
ately after moving it.
NOTE:
The turn signal and its indicator can be set
whether they flash three times after the
turn signal lever is returned via the infor-
mation display. Refer to “Information Dis-
play” in this section.
NOTE:
You can customize the setting for the num-
ber of times of flashing of the turn signal
and its indicator (1 to 4 times). Please ask
an D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S for
the customization.
+ D ] D U G : D U Q L Q J 6 Z L W F K
61M0163
Push in the hazard warning switch to acti-
vate the hazard warning lights. All turn sig-
nal lights and both turn signal indicators
will flash simultaneously. To turn off the
lights, push the switch again.
Use the hazard warning lights to warn
other traffic during emergency parking or
when your vehicle could otherwise become
a traffic hazard.
: L Q G V K L H O G : L S H U D Q G : D V K H U
/ H Y H U
57L21128
( ; $ 0 3 / (
: $ 5 1 , 1 *
7 R D Y R L G S R V V L E O H L Q M X U \ G R Q R W R S H U
D W H F R Q W U R O V E \ U H D F K L Q J W K U R X J K W K H
V W H H U L Q J Z K H H O
Page 101 of 288
Downloaded from www.Manualslib.com manuals search engine
2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
4) Make sure the hood is fully closed and
latched.
5) Check the headlights, turn signal lights,
brake lights and horn for proper opera-
tion.
6) Adjust the seat and head restraint.
7) Check the brake pedal and the parking
brake lever.
8) Adjust the mirrors.
9) Make sure that you and all passengers
have properly fastened the seat belts.
10)Make sure that all warning lights come
on as the ignition switch is turned to the
“ON” position or the engine switch is
pressed to change the ignition mode to
ON.
11)Check all gauges.
12)Make sure that the BRAKE SYSTEM
WARNING light turns off when the park-
ing brake is released.
Once a week, or each time you fill your fuel
tank, perform the following under-hood
checks:
1) Engine oil level
2) Coolant level
3) Brake fluid level
4) Battery electrolyte level
5) Windshield washer fluid level
6) Hood latch operation
Pull the hood release handle inside the
vehicle. Make sure that you cannot
open the hood all the way without
releasing the secondary latch. Be sure
to close the hood securely after check-
ing for proper latch operation. See theitem “All latches, hinges and locks” of
Page 105 of 288
Downloaded from www.Manualslib.com manuals search engine
2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
NOTE:
In the presence of strong radio signals or
noise, you may not be able to change the
ignition mode to ACC or ON or to start the
engine using the engine switch. In this
case, the information display on the instru-
ment cluster will show the following mes-
sage: KEY FOB NOT DETECTED. 8 Q U H O H D V H G 6 W H H U L Q J / R F N : D U Q L Q JIf the steering lock remains engaged when
you press the engine switch to change the
ignition mode to “ON”, the information dis-
play in the instrument cluster shows the
message: “TRN. STEERING WHEEL TO
RELEASE LOCK”. Refer to “Information
Display” in the ³ % ( ) 2 5 ( ' 5 , 9 , 1 * ´ sec-
tion for details.
NOTE:
The steering lock may not be released if
some load is acting on the steering wheel.
If this happens, turn the steering wheel to
the right or left to relieve it from the load
before you press the engine switch again
to change to the desired ignition mode.
. H \ O H V V 3 X V K 6 W D U W 6 \ V W H P
L I H T X L S S H G Provided the keyless push start system
remote controller is within the “interior
workable area” (refer to the related expla-
nation in this section), you can use the
engine switch for starting the engine and
selecting an ignition mode (ACC or ON). In
addition, the following functions can be
used:
• Keyless entry function. Refer to “Keyless
Push Start System Remote Controller” in
the “BEFORE DRIVING” section for
details.
• Locking and unlocking doors (including
the tailgate) using a request switch.
Refer to “Keyless Push Start System
Remote Controller” in the “BEFORE
DRIVING” section for details.
• Immobilizer (anti-theft) function. Refer to
“Immobilizer System” in the “BEFORE
DRIVING” section for details. ( Q J L Q H 6 Z L W F K , O O X P L Q D W L R QThe engine switch is illuminated (lit) in the
following situations:
• When the engine is off and the driver’s
door is open or for 15 seconds after the
drivers door is closed.
• When the engine is off and the position
lights are on. The illumination will go out
when the position lights are turned off.
• When the engine is on and the position
lights and/or the headlights are on. Theillumination will go out when the head-
lights are turned off.
82K253
NOTE:
To save the battery, the illumination will be
automatically turned off when both of the
following conditions are simultaneously
met:
• The headlights and position lights are
turned off.
• A period of 15 minutes has elapsed after
opening the driver’s door. 6 H O H F W L R Q R I , J Q L W L R Q 0 R G H VPress the engine switch to select the
“ACC” or “ON” mode as follows when you
use an electric accessory or check the
operation of instruments without running
the engine.
1) Bring the keyless push start system
remote controller with you and sit in the
driver’s seat.
Page 135 of 288
Downloaded from www.Manualslib.com manuals search engine
' 5 , 9 , 1 * 7 , 3 6
0 6 (
' R ¶ V D Q G ' R Q W ¶ V I R U 6 D I H
' U L Y L Q JExercise care in handling your vehicle. Be
conscious of not only your own safety but
also the safety of others on the road, and
thus enjoy the best and most comfortable
driving experience.
This section contains basic rules for safe
driving. Read it carefully for good under-
standing of the content so that you can
enjoy safe and pleasant driving in your
vehicle.
6 W D U W L Q J
1) Adjust the driver’s seat for the proper
driving posture.
2) Adjust the rear view mirror so as to
obtain the best possible rear view.
3) Before moving off, look forward and
back to confirm safety.4) Don’t start quickly, since it is dangerous
and wastes fuel.
* H Q H U D O G U L Y L Q J
1) Be sure to stop before the stop light and
stop sign. When moving into the inter-
section without any traffic lights or
signs, drive slowly to confirm safety.
72F-08-002
2) Always follow other vehicles at a safe
distance in order to prevent a rear-end
collision, in case the vehicle ahead
make a sudden stop.
3) Turn ON the turn signal at least 30
meters before making a turn or chang-
ing the lane so as not to be hit from
behind.
4) Before entering a corner, decelerate to
a safe speed. Don’t apply brakes during
cornering, or a cornering skid may
occur.5) When overtaking other vehicles, watch
out for the oncoming vehicle and care-
fully confirm the safety.
6) Don’t attempt zigzag driving which will
hinder your control over the vehicle and
cause an accident.
72F-08-011
% U D N L Q J
1) Use the parking brake when parking
your vehicle and shift the gear shift
lever into the first gear or reverse gear
position for the sake of safety.
Page 178 of 288
Downloaded from www.Manualslib.com manuals search engine 2 7 + ( 5 & 2 1 7 5 2 / 6 $ 1 ' ( 4 8 , 3 0 ( 1 7
0 6 (
6 H O H F W L Q J W K H ) 0 E D Q G
Press the FM button (1).
Each time the button is pressed, the recep-
tion band will change as follows:
6 H O H F W L Q J W K H $ 0 E D Q G
Press the AM button (2).
6 H H N W X Q L Q J
Press the seek Up button (3) or the seek
Down button (4).
The unit stops searching for a station at a
frequency where a broadcast station is
available.
0 D Q X D O W X Q L Q J
Turn the TUNE FOLDER PUSH SOUND
knob (5).
The frequency being received is displayed. 3 U H V H W P H P R U \
1) Select the desired station.
2) Hold down a desired button ([1] to [6])
of the Preset buttons (6) to which you
want to store the station for 2 seconds
or longer. $ X W R V W R U H
Hold down the AST button (7) for 2 sec-
onds or longer.
Six stations in good reception will automat-
ically be stored to the Preset buttons (6) in
order, starting from a station whose fre-
quency is the lowest.
NOTE:
• Auto store can be released by pressing
AST button (7) while auto store is under
way.
• When the auto store is performed, the
station previously stored in the memory
at the position is overwritten.
• When there are fewer than 6 stations
that can be stored even if 1 round of
auto store operation is performed, no
station will be stored at the remaining
Preset buttons (6).
• 6 stations can be preset for FM1 and
FM2 in common, and 6 stations for AM
in auto store mode.
$ X W R V W R U H P R G H R Q R I I
Press the AST button (7).
Each time the button is pressed, the mode
is switched as follows: 5 D G L R 5 H F H S W L R Q
Radio reception can be affected by envi-
ronment, atmospheric conditions, or radio
signal’s power and distance from the sta-
tion. Nearby mountains and buildings may
interfere or deflect radio reception, causing
poor reception. Poor reception or radio
static can also be caused by electric cur-
rent from overhead wires or high voltage
power lines. FM1 FM2
AST mode on AST mode off
Page 212 of 288
Downloaded from www.Manualslib.com manuals search engine 2 7 + ( 5 & 2 1 7 5 2 / 6 $ 1 ' ( 4 8 , 3 0 ( 1 7
0 6 (
5 D G L R R S H U D W L R Q V
/TUNE
VOL -VOL + FLD/TUNE
MODE
AS
SOUND
1
5
4
FLDENT
SEEK
TRACK
SEEK
TRACK
RPT RDM
6
MENU
3 2DISP
NOTE:
When there are fewer than 6 stations that can be stored even if 1 round of auto store operation is performed, no station will be
stored at the remaining preset buttons.
Press to return to the last received frequency
Press it for 2 seconds or longer. It selects the
stations with the stronger signals and stores
them in order. $ 6 E X W W R Q
Press to select the radio station. 6 ( ( . 7 5 $ & . 8 3 ' 2 : 1 E X W W R QPress to select the desired preset station. 3 5 ( 6 ( 7 E X W W R Q V
in the previous auto store mode.
Page 217 of 288
Downloaded from www.Manualslib.com manuals search engine
2 7 + ( 5 & 2 1 7 5 2 / 6 $ 1 ' ( 4 8 , 3 0 ( 1 7
0 6 (
7 U R X E O H V K R R W L Q JWhen encountered a problem, check and follow the instructions as described below.
If the described suggestions do not solve the problem, it is recommended to take the unit to your D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S
3 U R E O H P
3 R V V L E O H F D X V H
3 R V V L E O H V R O X W L R Q
& R P P R Q
Unable to operate The security function is on.When “SECURITY” is displayed, enter
the ID.
When “HELP” is displayed, contact your
D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S
Unable to turn on the power (no sound).
(No sound is produced)Fuse is blown.Contact your D X W K R U L V H G 0 D U X W L
6 X ] X N L Z R U N V K R S
5 D G L R
Much noiseIt may not be exactly tuned in to the sta-
tion.Tune it in exactly to the station.
Unable to receive by auto tuningThere may be no station emitting signals
powerful enough.Pick up a station by manual tuning.
& '
Sound skips or noise producedThe disc is dirty. Wipe the disc with a soft cloth.
The disc has a major scratch or is
warped.Replace the disc with the one with no
scratch and also not warped.