2015 SUZUKI NEXA stop start
[x] Cancel search: stop startPage 111 of 288
Downloaded from www.Manualslib.com manuals search engine
2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 ( 6 W D U W L Q J W K H ( Q J L Q H
9 H K L F O H Z L W K . H \ O H V V 3 X V K 6 W D U W
6 \ V W H P
% H I R U H 6 W D U W L Q J W K H ( Q J L Q H
64MS169
1) Make sure the parking brake is set fully.
2) Shift to “N” (Neutral) and fully depress
the clutch pedal. Hold the clutch and
brake pedals fully depressed.
82K254
3) The “PUSH START SWITCH” message
will appear on the information display in
the instrument cluster. Push the engine
switch (1). When the engine is started,
the starter motor will automatically stop.
NOTE:
• You do not need to keep the engine
switch pressed to start the engine.
• The engine of a manual transaxle vehi-
cle will not start unless the clutch pedal
is depressed.
• During the engine starting procedure,
messages on the information display will
help you. Refer to “Information Display”in the “BEFORE DRIVING” section for
details.
• You should turn off such loads as the
headlights and air conditioning system to
facilitate starting of the engine.
• Even if you fail to start the engine, the
starter motor will stop operating auto-
matically after a short time. After the
starter motor has stopped or if there is
some problem with the system, the
starter motor will rotate only while the
engine switch is being pressed.
6 W R S S L Q J W K H H Q J L Q H• Depress the engine switch to stop the
engine after the vehicle stopped com-
pletely.
• In case of emergency, you can stop the
engine by quickly pushing the engine
switch more than 3 times, or pushing
and holding the engine switch more than
2 seconds while the vehicle in motion.
NOTE:
Except in emergency, do not stop the
engine while the vehicle in motion.
The steering and braking operation will
require more efforts when the engine
stopped.
Refer to “Braking” in this section.
• If the engine has been stopped and
stayed as it as for while after the engine
was stopped unexpectedly or was raced
before stopped, a clicking sound may be
heard from around the engine when
engine restarted. This is not a malfunc-
(1)
: $ 5 1 , 1 *
0 D N H V X U H W K D W W K H S D U N L Q J E U D N H L V
V H W I X O O \ D Q G W K H W U D Q V D [ O H L V L Q 1 H X
W U D O E H I R U H D W W H P S W L Q J W R V W D U W W K H
H Q J L Q H
NOTICE
Page 112 of 288
Downloaded from www.Manualslib.com manuals search engine 2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
tion. In this case, always let the engine
idle before stop it. 6 W D U W L Q J D & R O G D Q G : D U P ( Q J L Q H & R O G H Q J L Q H
Depress the clutch and brake pedals fully
and press the engine switch to crank the
engine. If the glow plug indicator light
comes on, the engine will start automati-
cally after the glow plug indicator light goes
off or 10 seconds past.
: D U P H Q J L Q H
Crank the engine by pressing the engine
switch to change the ignition mode to
“START”. & D X W L R Q Z K H Q V W R S S L Q J W K H H Q J L Q H Z L W K
W X U E R F K D U J H U
When stopping the engine after climbing or
high speed driving, let the engine idle for
about one minute or more (if it is not pro-
hibited) to cool down the turbocharger and
engine oil. This is to prevent the engine oil
from over-deteriorating. Deteriorated
engine oil will damage the bearings of the
turbocharger.
5 H V W D U W L Q J G L H V H O H Q J L Q H D I W H U I X H O
H P S W \ V W R S
If the engine stops and the low fuel warn-
ing light and the malfunction indicator light
come on, use the following procedure:
1) Fill the fuel tank.
2) Press the engine switch to change the
ignition mode to “ON” for 5-10 seconds
to feed fuel.
3) Perform above engine starting proce-
dure to start the engine.
If the malfunction indicator light still comes
on after the engine started, there may be
some problem with the engine. Ask your
D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S to have
the engine inspected.
, I W K H 0 $ 6 7 ( 5 : $ 5 1 , 1 * L Q G L F D W R U O L J K W
E O L Q N V D Q G W K H H Q J L Q H F D Q Q R W E H V W D U W H G
Your keyless push start system remote
controller may not be sensed as being
within the interior workable area. Try again
after making sure that you have the remote
controller with you. If the engine still can-
not be started, the battery of the remote
controller may be discharged. You mustthen use the following method to be able to
start the engine.
58MST0302
1) Make sure the parking brake is set fully.
2) Shift to “N” (Neutral) and fully depress
the clutch pedal. Hold the clutch and
brake pedals fully depressed.
3) The “PUSH START SWITCH.” mes-
sage will appear on the information dis-
play in the instrument cluster. Press the
engine switch (1).
4) Within about 10 seconds of blinking of
the “MASTER WARNING” indicator
light in the instrument cluster, touch the
engine switch with the lock button end
of the remote controller (2) for about 2
seconds.
NOTE:
• If you still cannot start the engine after
several attempts using the above
NOTICE
' R Q R W F U D Q N W K H H Q J L Q H I R U P R U H
W K D Q V H F R Q G V D W D W L P H
, I W K H H Q J L Q H G R H V Q
Page 126 of 288
Downloaded from www.Manualslib.com manuals search engine 2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
, I W K H U H D U Y L H Z I U R P W K H U H D U Y L H Z F D P
H U D L V Q R W V K R Z Q R U W K H U H L V D S R R U
L P D J H• If the rear view from the rearview camera
is not shown.
– Check to make sure that the ignition
switch is in the “ON” position or the
ignition mode is “ON”.
– Check to make sure that the gearshift
lever is shifted to the “R” position.• If the image from the rearview camera is
poor.– Check to make sure that the camera
lens is not dirty.
– Check to make sure that light from the
sun or the beam of the headlights from
the vehicle behind is not shining
directly into the lens.
If the rearview camera system is still not
working properly after checking the above,
have the system inspected by an
D X W K R U L V H G
0 D U X W L 6 X ] X N L Z R U N V K R S
as soon as
possible.
% U D N L Q J
60G165S
The distance needed to bring any vehicle to
a halt increases with the speed of the vehi-
cle. The braking distance needed, for exam-
ple, at 60 km/h (37 mph) will be
approximately 4 times greater than the
braking distance needed at 30 km/h (19
mph). Start to brake the vehicle when there
is plenty of distance between your vehicle
and the stopping point, and slow down
gradually.
3 R Z H U $ V V L V W H G % U D N H V L I
H T X L S S H G Your vehicle has power-assisted brakes. If
power assistance is lost due to a stalled
engine or other failures, the system is still
fully operational on reserve power and you
can bring the vehicle to a complete stop by
pressing the brake pedal once and holding
it down. The reserve power is partly used
up when you depress the brake pedal and
reduces each time the pedal is pressed.
Apply smooth and even pressure to the
pedal. Do not pump the pedal.
: $ 5 1 , 1 *
, I Z D W H U J H W V L Q W R W K H E U D N H G H Y L F H V
E U D N H S H U I R U P D Q F H P D \ E H F R P H S R R U
D Q G X Q S U H G L F W D E O H $ I W H U G U L Y L Q J
W K U R X J K Z D W H U R U Z D V K L Q J W K H X Q G H U
V L G H R I W K H Y H K L F O H W H V W W K H E U D N H V
Z K L O H G U L Y L Q J D W D V O R Z V S H H G W R V H H L I
W K H \ K D Y H P D L Q W D L Q H G W K H L U Q R U P D O
H I I H F W L Y H Q H V V , I W K H E U D N H V D U H O H V V
H I I H F W L Y H W K D Q Q R U P D O G U \ W K H P E \
G U L Y L Q J V O R Z O \ X Q W L O W K H E U D N H V K D Y H
U H J D L Q H G W K H L U Q R U P D O H I I H F W L Y H Q H V V
: $ 5 1 , 1 *
( Y H Q Z L W K R X W U H V H U Y H S R Z H U L Q W K H
E U D N H V \ V W H P \ R X F D Q V W L O O V W R S W K H
Y H K L F O H E \ S U H V V L Q J W K H E U D N H S H G D O
K D U G H U W K D Q Q R U P D O O \ U H T X L U H G + R Z
H Y H U W K H V W R S S L Q J G L V W D Q F H P D \ E H
O R Q J H U
Page 128 of 288
Downloaded from www.Manualslib.com manuals search engine 2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
+ R Z W K H $ % 6 : R U N VA computer continuously monitors wheel
speed. The computer compares the
changes in wheel speed when braking. If
the wheels slow suddenly, indicating a
skidding situation, the computer will
change braking pressure several times
each second to prevent the wheels from
locking. When you start your vehicle or
when you accelerate after a hard stop, you
may hear a momentary motor or clicking
noise as the system resets or checks
itself." This is absolutely normal and indi-
cates that ABS is functioning properly"
: $ 5 1 , 1 *
Page 131 of 288
Downloaded from www.Manualslib.com manuals search engine
' 5 , 9 , 1 * 7 , 3 6
0 6 (
54G584S
, P S U R Y L Q J ) X H O ( F R Q R P \The following instructions will help you
improve fuel economy.
$ Y R L G H [ F H V V L Y H L G O L Q J
If you are to wait for more than a minute
while you are parked, stop the engine and
start it again later. When warming up a
cold engine, allow the engine to idle until
the temperature gauge pointer comes up
to the “C” position (if the idling is not pro-
hibited). In this position, the engine is suffi-
ciently warm for starting off.
$ Y R L G I D V W V W D U W V
Fast starts away from lights or stop signs
will consume fuel unnecessarily and
shorten engine life. Start off slowly.
$ Y R L G X Q Q H F H V V D U \ V W R S V
Avoid unnecessary deceleration and stop-
ping. Try to maintain a slow, steady speed
whenever possible. Slowing down and
then accelerating again uses more fuel.
. H H S D V W H D G \ F U X L V L Q J V S H H G
Keep as constant a speed as road and
traffic conditions will permit.
. H H S Z H L J K W W R D P L Q L P X P
The heavier the load, more the fuel vehicle
consumes. Take out any luggage or cargo
when it is not necessary.
. H H S W L U H S U H V V X U H V F R U U H F W
Underinflation of the tires can waste fuel
due to increased running resistance of the
tires. Keep your tires inflated to the correct
NOTICE
7 R P L Q L P L ] H W K H S R V V L E L O L W \ R I F D W D O \ V W
R U R W K H U Y H K L F O H G D P D J H
Page 135 of 288
Downloaded from www.Manualslib.com manuals search engine
' 5 , 9 , 1 * 7 , 3 6
0 6 (
' R ¶ V D Q G ' R Q W ¶ V I R U 6 D I H
' U L Y L Q JExercise care in handling your vehicle. Be
conscious of not only your own safety but
also the safety of others on the road, and
thus enjoy the best and most comfortable
driving experience.
This section contains basic rules for safe
driving. Read it carefully for good under-
standing of the content so that you can
enjoy safe and pleasant driving in your
vehicle.
6 W D U W L Q J
1) Adjust the driver’s seat for the proper
driving posture.
2) Adjust the rear view mirror so as to
obtain the best possible rear view.
3) Before moving off, look forward and
back to confirm safety.4) Don’t start quickly, since it is dangerous
and wastes fuel.
* H Q H U D O G U L Y L Q J
1) Be sure to stop before the stop light and
stop sign. When moving into the inter-
section without any traffic lights or
signs, drive slowly to confirm safety.
72F-08-002
2) Always follow other vehicles at a safe
distance in order to prevent a rear-end
collision, in case the vehicle ahead
make a sudden stop.
3) Turn ON the turn signal at least 30
meters before making a turn or chang-
ing the lane so as not to be hit from
behind.
4) Before entering a corner, decelerate to
a safe speed. Don’t apply brakes during
cornering, or a cornering skid may
occur.5) When overtaking other vehicles, watch
out for the oncoming vehicle and care-
fully confirm the safety.
6) Don’t attempt zigzag driving which will
hinder your control over the vehicle and
cause an accident.
72F-08-011
% U D N L Q J
1) Use the parking brake when parking
your vehicle and shift the gear shift
lever into the first gear or reverse gear
position for the sake of safety.
Page 137 of 288
Downloaded from www.Manualslib.com manuals search engine
' 5 , 9 , 1 * 7 , 3 6
0 6 (
when the windshield glass is dry or the
wiper blade and glass may get dam-
aged.
72F-08-021
72F-08-022
0 D U J L Q ) R U 6 D I H W \It is important to allow yourself a margin for
safety during driving so that you can cope
with erroneous or unexpected driving of other
drivers. For that, observe the following.•Drive at a safe speed.
•Maintain a sufficient distance between
your vehicle and the vehicle ahead.
• Don’t force yourself to overtake other
vehicles.
• Don’t make quick start, hard steering or
sudden stops.
• Allow an ample time in the driving
schedule.
• Observe traffic rules and regulations. & R Q F O X V L R QA perfect driver does not exist. The
endeavour of every motorist should be to
strive for perfection. Safety consciousness
not only ensures your safety and the safety
of other road users, it also helps reduce
the wear and tear on your vehicle, prolongs
its life, gives more mileage and ensures a
comfortable driving experience.
) R O O R Z W K H G R
Page 178 of 288
Downloaded from www.Manualslib.com manuals search engine 2 7 + ( 5 & 2 1 7 5 2 / 6 $ 1 ' ( 4 8 , 3 0 ( 1 7
0 6 (
6 H O H F W L Q J W K H ) 0 E D Q G
Press the FM button (1).
Each time the button is pressed, the recep-
tion band will change as follows:
6 H O H F W L Q J W K H $ 0 E D Q G
Press the AM button (2).
6 H H N W X Q L Q J
Press the seek Up button (3) or the seek
Down button (4).
The unit stops searching for a station at a
frequency where a broadcast station is
available.
0 D Q X D O W X Q L Q J
Turn the TUNE FOLDER PUSH SOUND
knob (5).
The frequency being received is displayed. 3 U H V H W P H P R U \
1) Select the desired station.
2) Hold down a desired button ([1] to [6])
of the Preset buttons (6) to which you
want to store the station for 2 seconds
or longer. $ X W R V W R U H
Hold down the AST button (7) for 2 sec-
onds or longer.
Six stations in good reception will automat-
ically be stored to the Preset buttons (6) in
order, starting from a station whose fre-
quency is the lowest.
NOTE:
• Auto store can be released by pressing
AST button (7) while auto store is under
way.
• When the auto store is performed, the
station previously stored in the memory
at the position is overwritten.
• When there are fewer than 6 stations
that can be stored even if 1 round of
auto store operation is performed, no
station will be stored at the remaining
Preset buttons (6).
• 6 stations can be preset for FM1 and
FM2 in common, and 6 stations for AM
in auto store mode.
$ X W R V W R U H P R G H R Q R I I
Press the AST button (7).
Each time the button is pressed, the mode
is switched as follows: 5 D G L R 5 H F H S W L R Q
Radio reception can be affected by envi-
ronment, atmospheric conditions, or radio
signal’s power and distance from the sta-
tion. Nearby mountains and buildings may
interfere or deflect radio reception, causing
poor reception. Poor reception or radio
static can also be caused by electric cur-
rent from overhead wires or high voltage
power lines. FM1 FM2
AST mode on AST mode off