Page 96 of 288
Downloaded from www.Manualslib.com manuals search engine % ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
5 H S U R J U D P P L Q J W K H U D L Q V H Q V L Q J Z L S H U
I X Q F W L R QThe “AUTO” position operation of the rain-
sensing wiper function can be customized
to your preference by reprogramming its
setting as follows. Please contact an D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S
for
this customization. ) X O O D X W R P D W L F Z L S L Q J I D F W R U \ V H W W L Q J
The system automatically selects the most
appropriate of the following wiping modes:
no wiping, intermittent wiping, low-speed
wiping, and high-speed wiping.
6 H P L D X W R P D W L F Z L S L Q J
The system automatically selects the most
appropriate of the following wiping modes:
intermittent wiping, low-speed wiping, or
high-speed wiping. (The wipers do not stop
automatically.)
, Q W H U P L W W H Q W Z L S L Q J
The wipers operate only in the intermittent
wiping mode. The wiping interval can be
changed with the knob on the control lever.
: L Q G V K L H O G : D V K H U
64MS067
To spray windshield washer fluid, pull the
lever toward you. The windshield wipers
will automatically turn on at low speed if
they are not already on and the “INT” posi-
tion is equipped.
: $ 5 1 , 1 *
Page 97 of 288
Downloaded from www.Manualslib.com manuals search engine
% ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
5 H D U : L Q G R Z : L S H U : D V K H U 6 Z L W F K
L I H T X L S S H G
64MS068
To turn the rear wiper on, twist the rear
wiper switch on the end of the lever forward
to the “ON” position. If your vehicle is
equipped the “INT” position, the rear wiper
operates intermittently when you twist the
switch forward to the “INT” position. To turn
the rear wiper off, twist the switch rearward
to the “OFF” position.With the rear wiper in the “OFF” position,
twist the switch rearward and hold it there
to spray window washer fluid.
With the rear wiper in the “ON” position,
turn the switch forward and hold it there to
spray window washer fluid.
7 L O W 7 H O H V F R S L Q J L I H T X L S S H G 6 W H H U
L Q J / R F N / H Y H U
61MM0A085
(1) LOCK
(2) UNLOCK
The lock lever is located under the steering
column. To adjust the steering wheel
height and fore-aft position:
1) Push down the lock lever to unlock the
steering column.
2) Adjust the steering wheel to the desired
height and fore-aft position and lock the
steering column by pulling up the lock
lever.
3) Try moving the steering wheel up and
down and back and forth to make sure
it is securely locked in position.
( ; $ 0 3 / (
Intermittent wiper WasherWiper
NOTICE
& O H D U L F H R U V Q R Z I U R P W K H U H D U Z L Q
G R Z D Q G U H D U Z L S H U E O D G H E H I R U H
X V L Q J W K H U H D U Z L S H U $ F F X P X O D W H G
L F H R U V Q R Z F R X O G S U H Y H Q W W K H Z L S H U
E O D G H I U R P P R Y L Q J F D X V L Q J G D P D J H
W R W K H Z L S H U P R W R U
: $ 5 1 , 1 *
1 H Y H U D W W H P S W W R D G M X V W W K H V W H H U L Q J
Z K H H O Z K L O H W K H Y H K L F O H L V P R Y L Q J R U
\ R X F R X O G O R V H F R Q W U R O R I W K H Y H K L F O H
(2) ( ; $ 0 3 / (
( )
Page 101 of 288
Downloaded from www.Manualslib.com manuals search engine
2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
4) Make sure the hood is fully closed and
latched.
5) Check the headlights, turn signal lights,
brake lights and horn for proper opera-
tion.
6) Adjust the seat and head restraint.
7) Check the brake pedal and the parking
brake lever.
8) Adjust the mirrors.
9) Make sure that you and all passengers
have properly fastened the seat belts.
10)Make sure that all warning lights come
on as the ignition switch is turned to the
“ON” position or the engine switch is
pressed to change the ignition mode to
ON.
11)Check all gauges.
12)Make sure that the BRAKE SYSTEM
WARNING light turns off when the park-
ing brake is released.
Once a week, or each time you fill your fuel
tank, perform the following under-hood
checks:
1) Engine oil level
2) Coolant level
3) Brake fluid level
4) Battery electrolyte level
5) Windshield washer fluid level
6) Hood latch operation
Pull the hood release handle inside the
vehicle. Make sure that you cannot
open the hood all the way without
releasing the secondary latch. Be sure
to close the hood securely after check-
ing for proper latch operation. See theitem “All latches, hinges and locks” of
Page 260 of 288
Downloaded from www.Manualslib.com manuals search engine , 1 6 3 ( & 7 , 2 1 $ 1 ' 0 $ , 1 7 ( 1 $ 1 & (
0 6 (
65D151
NOTE:
Do not flex the wiper blade frame end more
than necessary. If you do, it can break off.
54G135
(1) Retainer
4) If the new blade is provided without the
two metal retainers, move them from
the old blade to the new one.
5) Install the new blade in the reverse
order of removal.Make sure the blade is properly
retained by all the hooks.
6) Reinstall wiper frame to arm in the
reverse order of removal.
: L Q G V K L H O G : D V K H U ) O X L G
64MS097
Check that there is washer fluid in the tank
by looking at the washer fluid level gauge
which is attached to the cap of the washer
fluid tank. If the fluid level is near empty,
refill it. Use a good quality windshield
washer fluid, diluted with water as neces-
sary.
( ; $ 0 3 / (
( ; $ 0 3 / (
( ; $ 0 3 / (
: $ 5 1 , 1 *
' R Q R W X V H U D G L D W R U D Q W L I U H H ] H L Q W K H
Z L Q G V K L H O G Z D V K H U U H V H U Y R L U 7 K L V
F D Q V H Y H U H O \ L P S D L U Y L V L E L O L W \ Z K H Q
V S U D \ H G R Q W K H Z L Q G V K L H O G D Q G D O V R
G D P D J H \ R X U Y H K L F O H