2015 SUZUKI NEXA change time
[x] Cancel search: change timePage 69 of 288
Downloaded from www.Manualslib.com manuals search engine
% ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
, Q V W D Q W D Q H R X V I X H O F R Q V X P S W L R Q
The display shows instantaneous fuel con-
sumption with a bar graph only when the
vehicle is moving.
NOTE:
• The display does not show the bar graph
unless the vehicle is moving.
• Depending on the vehicle’s specification,
the fuel consumption units of initial set-
ting are indicated as L/100km, km/L or
MPG.
• For “L/100km” or “km/L” setting, the indi-
cated maximum value of instantaneous
fuel consumption is 30. No more than 30
will be indicated on the display even if
the actual instantaneous fuel consump-
tion is higher.
• For “MPG” setting, the indicated maxi-
mum value of instantaneous fuel con-
sumption is 80. No more than 80 will be
indicated on the display even if the
actual instantaneous fuel consumption is
higher.
• The indication on the display may be
delayed if fuel consumption is greatly
affected by driving conditions.
• The display shows estimated values.
Indications may not be the same as
actual values.
$ Y H U D J H I X H O F R Q V X P S W L R Q
If you selected average fuel consumption
the last time you drove the vehicle, the dis-
play shows the last value of average fuel
consumption from previous driving when
the ignition switch is turned to the “ON”position or the engine switch is pressed to
change the ignition mode to “ON”. Unless
you reset the value of average fuel con-
sumption, the display indicates the value of
average fuel consumption which includes
average fuel consumption during previous
driving.
NOTE:
When you reconnect the negative (–) ter-
minal to the battery, the value of average
fuel consumption will be shown after driv-
ing for a period of time.
You can select when the value of average
fuel consumption is reset from among the
following three methods;
• Reset after refuel: the value of average
fuel consumption will be reset automati-
cally by refueling.
• Reset with trip A: the value of average
fuel consumption will be reset automati-
cally by resetting trip meter A.
• Reset manually: the value of average
fuel consumption will be reset by push-
ing and holding the indicator selector
knob (2) when the display indicates the
average fuel consumption.
To change when the value of average fuel
consumption is reset, refer to “Setting
Mode” later in this section.
NOTE:
If you add only a small amount of fuel
when you select “Reset after refuel”, the
average fuel consumption value may not
be reset. ' U L Y L Q J U D Q J H
If you selected driving range the last time
you drove the vehicle, the display indicates
“---” for a few seconds and then indicates
the current driving range when the ignition
switch is turned to the “ON” position or the
engine switch is pressed to change the
ignition mode to ON.
The driving range shown in the display is
the approximate distance you can drive
until the fuel gauge indicates “E”, based on
current driving conditions.
When the low fuel warning light comes on,
the display “---” will appear.
If the low fuel warning light comes on, fill
the fuel tank immediately.
As the driving range after refueling is cal-
culated based on the most recent driving
condition, the value is different each time
you refuel.
NOTE:
• If you refuel when the ignition switch is in
the “ON” position or the ignition mode is
“ON”, the driving range may not indicate
the correct value.
• When you reconnect the negative (–)
terminal to the battery, the value of driv-
ing range will be shown after driving for a
period of time.
Page 70 of 288
Downloaded from www.Manualslib.com manuals search engine % ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
$ Y H U D J H 6 S H H G
If you selected average speed the last time
you drove the vehicle, the display indicates
the last value of average speed from
previous driving when the ignition switch is
turned to the “ON” position or the engine
switch is pressed to change the ignition
mode to “ON”. Unless you reset the value
of average speed, the display indicates the
value of average speed which includes
average speed during previous driving.
To reset the value of average speed, push
and hold the indicator selector knob (2) for
about 2 seconds when the display indicates
an average speed. The display shows “---”
and then indicates a new average speed
after driving for a short time.
NOTE:
When you reconnect the negative (–) ter-
minal to the battery, the value of average
speed will be shown after driving for a
period of time. 7 U L S 0 H W H UThe display (D) shows the trip meter.
The trip meter can be used to measure the
distance traveled on short trips or between
fuel stops.
You can use the trip meter A or trip meter B
independently.
To reset the trip meter to zero, push and
hold the trip meter selector knob (3) for
about 2 seconds when the display shows
the trip meter.
2 G R P H W H UThe display (E) shows the odometer.
The odometer records the total distance
the vehicle has been driven. 6 H W W L Q J 0 R G HWhen the ignition switch is in the “ON”
position or the ignition mode is ON and the
vehicle is stationary, you can enter the set-
ting mode of the information display by
pushing and holding the indicator selector
knob (2) for more than 3 seconds.
• To select the setting that you want to
change, turn the indicator selector knob
(2) left or right.
• To change the setting, push the indicator
selector knob (2).
• To exit the setting mode, select “Back”
and push the indicator selector knob (2).
61MM0A161
NOTE:
The currently selected setting item is indi-
cated enclosed by a frame.
NOTE:
• If you push and hold the indicator selec-
tor knob (2) to enter the setting mode
when the display (D) shows average fuel
consumption or average speed, the
value will be reset simultaneously. If you
do not want to reset the value, push the
indicator selector knob quickly to switch
the indication of the display.
• If you turn the ignition switch, press the
engine switch or start to move the vehi-
cle when the display is in the setting
mode, the setting mode will be canceled
automatically.
NOTICE
. H H S W U D F N R I \ R X U R G R P H W H U U H D G L Q J
D Q G F K H F N W K H P D L Q W H Q D Q F H V F K H G
X O H U H J X O D U O \ I R U U H T X L U H G V H U Y L F H V
, Q F U H D V H G Z H D U R U G D P D J H W R F H U W D L Q
S D U W V F D Q U H V X O W I U R P I D L O X U H W R S H U
I R U P U H T X L U H G V H U Y L F H V D W W K H S U R S H U
P L O H D J H L Q W H U Y D O V
( ; $ 0 3 / (
Page 71 of 288
Downloaded from www.Manualslib.com manuals search engine
% ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
' L V W D Q F H X Q L W
2 G R W U L S P H W H U G L V W D Q F H X Q L W V V H W W L Q J
You can change the units odo/trip meter
distance is displayed in.
NOTE:
When you change the units odo/trip meter
distance is displayed in, the trip meter will
be reset automatically.
) X H O H F R Q R P \
) X H O F R Q V X P S W L R Q X Q L W V V H W W L Q J
You can change the units that fuel con-
sumption is displayed in.
/ D Q J X D J H
You can change the language of the infor-
mation display.
) X H O U H V H W $ Y H U D J H I X H O F R Q V X P S W L R Q
U H V H W V H W W L Q J
You can change when the value of aver-
age fuel consumption is reset.
7 H P S H U D W X U H
7 H P S H U D W X U H X Q L W V V H W W L Q J
You can change the units that temperature
is displayed in.
NOTE:
When you change the units that tempera-
ture is displayed in, the automatic heating
and air conditioning system (if equipped)
temperature display units will be changed
automatically. 6 H W 6 H Q V R U V
3 D U N L Q J V H Q V R U V L I H T X L S S H G V H W W L Q J
The parking sensor can be switched
between the normal mode and trailer
mode.
& O R F N V H W W L Q J
• To change the hour indication, turn the
indicator selector knob (2) left or right
repeatedly when the hour indication
appears as reversed color. To change
the hour indication quickly, turn and hold
the indicator selector knob (2). To set the
hour indication, push the indicator selec-
tor knob (2) and the minute indication
appears as reversed color.
• To change the minute indication, turn the
indicator selector knob (2) left or right
repeatedly when the minute indication
appears as reversed color. To change
the minute indication quickly, turn and
hold the indicator selector knob (2). To
set the minute indication, push the indi-
cator selector knob (2).
You can also switch the time indication
between 12-hour and 24-hour format. ' R R U / R F N ' R R U O R F N V H W W L Q J
Page 84 of 288
Downloaded from www.Manualslib.com manuals search engine % ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
2 S H Q ' R R U : D U Q L Q J / L J K W
54G391
This light remains on until all doors (includ-
ing the tailgate) are completely closed.
If any door (including the tailgate) is open
when the vehicle is moving, a ding sounds
to remind you to close all doors completely.
/ R Z ) X H O : D U Q L Q J / L J K W
54G343
If this light comes on, fill the fuel tank
immediately.
When this light comes on, a ding sounds
once to remind you to fill the fuel.
If you do not fill the fuel, a ding sounds
every time when the ignition switch is
turned to the “ON” position or the engine
switch is pressed to change the ignition
mode to ON.
NOTE:
The activation point of this light varies
depending on road conditions (for exam-
ple, slope or curve) and driving conditions
because of fuel moving in the tank.
( O H F W U L F 3 R Z H U 6 W H H U L Q J / L J K W
79J039
This light comes on when the ignition
switch is turned to the “ON” position or the
engine switch is pressed to change the
ignition mode to ON, and goes out when
the engine is started.
If this light comes on or blinks while driv-
ing, the power steering system may not
work properly. Have the system inspected
by your D X W K R U L V H G 0 D U X W L 6 X ] X N L
Z R U N V K R S
NOTE:
While parking or driving at very low speed
greater steering effort is required. This is
not a malfunction of the steering system
but power steering control system limiting
power assist in order to prevent it from
over heating.
• The steering wheel is operated very
often.
• The steering wheel is kept in a fully
turned position for a long while.
When the power steering control system
cools down, the power steering system is
restored back to the original condition.
Page 90 of 288
Downloaded from www.Manualslib.com manuals search engine % ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
To turn the lights on or off, twist the knob
on the end of the lever. There are four
positions:
2 ) )
All lights are off.
$ 8 7 2
This function works when it on mode has
been changed to ON by pressing the
engine switch. The headlights and position
lights are turned on and off automatically
according to the amount of outside light
detected by a sensor. They go out auto-
matically when you change the ignition
mode to “ACC” or “LOCK” (OFF) by press-
ing the engine switch.
The light sensor (5) for sensing the amount
of outside light is installed on the upper
part of the windshield. It also serves as the
rain sensor for the rain-sensing wipers.NOTE:
• Avoid covering the light sensor area of
the windshield with a sticker. The sticker
may impair the performance of the sen-
sor and make the system unable to con-
trol operation of the lights correctly.
• If you changed the ignition mode to ON
by pressing the engine switch and the
“AUTO” position remains selected, the
headlights and position lights come on
automatically as the outside gets dark
even with the engine not running. Leav-
ing the lights lit for a long time may lead
to a completely discharged battery.
Front position lights, tail lights, license
plate light and instrument lights are on, but
headlights are off.
Front position lights, tail lights, license
plate light, instrument lights and headlights
are on.
64MS061
With the headlights on, push the lever for-
ward to switch to the high beams (main
beams) or pull the lever toward you to
switch to the low beams. When the high
beams (main beams) are on, a light on the
instrument panel will come on. To momen-
tarily activate the high beams (main
beams) as a passing signal, pull the lever
slightly toward you and release it when you
have completed the signal.
$ X W R R Q K H D G O L J K W V \ V W H P
64MS062
The Auto-on headlight system automati-
cally turns on all lights that are operated by
the lighting control lever on the steering
column, when the following three condi-
tions are all met.
Conditions for Auto-on headlight system
operation:
1) It is dark around the light sensor (5).
2) The lighting control lever is in the
“AUTO” position.
3) You press the engine switch to change
the ignition mode to ON.
& $ 8 7 , 2 1
, I W K H O L J K W V H Q V R U D U H D R I W K H Z L Q G
V K L H O G L V F R Y H U H G Z L W K P X G L F H R U
R W K H U V L P L O D U V X E V W D Q F H V W K H K H D G
O L J K W V D Q G S R V L W L R Q O L J K W V P D \ E H
W X U Q H G R Q H Y H Q Z K H Q L W L V V W L O O O L J K W
R X W V L G H % H I R U H U H P R Y L Q J V X F K V X E
V W D Q F H V I U R P W K H Z L Q G V K L H O G D O Z D \ V
V H W W K H Z L S H U F R Q W U R O O H Y H U W R W K H
Page 94 of 288
Downloaded from www.Manualslib.com manuals search engine % ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
: L S H U D Q G : D V K H U 2 S H U D W L R QWhen the ignition switch is in the “ON” posi-
tion or the ignition mode is ON, you can use
the wiper/washer lever or switch (if
equipped). : L Q G V K L H O G : L S H U V
64MS063
To turn the windshield wipers on, move the
lever down to one of the three operating
positions. In the “INT” position, the wipers
operate intermittently. The “INT” position is
very convenient for driving in mist or light
rain. In the “LO” position, the wipers operate
at a steady low speed. In the “HI” position,
the wipers operate at a steady high speed.
To turn off the wipers, move the lever back
to the “OFF” position.
Move the lever up and hold it to the “MIST”
position, the windshield wipers will turn on
continuously at low speed.
64MS064
If the lever is equipped with the “INT TIME”
control, turn the control forward or rear-
ward to adjust the intermittent wiper opera-
tion to the desired interval.
: L Q G V K L H O G : L S H U V Z L W K 5 D L Q 6 H Q V
L Q J ) X Q F W L R Q L I H T X L S S H G
64MS065
Press the engine switch to change the igni-
tion mode to ON. To turn the rain-sensing
wipers on, move the lever down to one of
the three operating positions. In the “AUTO”
position (if provided), the wipers automati-
cally operate when the wiper system senses
rain or snow. In the “LO” position, the wipers
operate at a steady low speed. In the “HI”
position, the wipers operate at a steady high
speed. To turn off the wipers, move the lever
back to the “OFF” position.Move the lever up and hold it to the “MIST”
position; the wipers will operate continu-
ously at low speed for as long as you hold
the lever in the “MIST” position.
( ; $ 0 3 / (
( ; $ 0 3 / (
MIST
HI OFF
LO AUTO
( ; $ 0 3 / (
Page 101 of 288
Downloaded from www.Manualslib.com manuals search engine
2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
4) Make sure the hood is fully closed and
latched.
5) Check the headlights, turn signal lights,
brake lights and horn for proper opera-
tion.
6) Adjust the seat and head restraint.
7) Check the brake pedal and the parking
brake lever.
8) Adjust the mirrors.
9) Make sure that you and all passengers
have properly fastened the seat belts.
10)Make sure that all warning lights come
on as the ignition switch is turned to the
“ON” position or the engine switch is
pressed to change the ignition mode to
ON.
11)Check all gauges.
12)Make sure that the BRAKE SYSTEM
WARNING light turns off when the park-
ing brake is released.
Once a week, or each time you fill your fuel
tank, perform the following under-hood
checks:
1) Engine oil level
2) Coolant level
3) Brake fluid level
4) Battery electrolyte level
5) Windshield washer fluid level
6) Hood latch operation
Pull the hood release handle inside the
vehicle. Make sure that you cannot
open the hood all the way without
releasing the secondary latch. Be sure
to close the hood securely after check-
ing for proper latch operation. See theitem “All latches, hinges and locks” of
Page 106 of 288
Downloaded from www.Manualslib.com manuals search engine (1)
(2)
2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
2) Without depressing the clutch pedal,
press the engine switch (1).
82K254
Every time you press the engine switch,
the ignition mode changes as follows.
57L31033
NOTE:
When selecting the ignition modes, the
information display in the instrument clus-
ter shows certain messages. Refer to
“Information Display” in the “BEFORE
DRIVING” section for details. , I W K H 0 $ 6 7 ( 5 : $ 5 1 , 1 * L Q G L F D W R U O L J K W
E O L Q N V D Q G W K H L J Q L W L R Q P R G H V F D Q Q R W
E H V H O H F W H G
Your keyless push start system remote con-
troller may not be sensed as being within the
“interior workable area” (refer to the related
explanation in this section). Try again after
making sure you have the remote controller
with you. If the ignition modes still cannot be
selected, the battery of the remote controller
may be discharged. To be able to select an
ignition mode, you must then use the follow-
ing method:
58MST0302
1) Without depressing the brake pedal
and the clutch pedal, push the engine
switch (1).
2) Within about 10 seconds during which
the master warning indicator light in the
instrument cluster is blinking and the
“PLACE KEY FOB ON START
SWITCH” message appears on the
information display, touch the engineswitch with the lock button end of the
remote controller (2) for about 2 sec-
onds.
NOTE:
•
If you still cannot select the ignition
modes, there may be some problem with
the keyless push start system. Contact
an D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S
for an inspection of the system.
• The immobilizer/keyless push start sys-
tem warning light will come on for about
5 seconds while the master warning indi-
cator light is blinking. In addition, the
information display in the instrument
cluster will show a message during this
time. Refer to “Information Display” in
the “BEFORE DRIVING” section for
details.
•
You may customize the system to cause
the interior buzzer to sound once for the
remote controller out of sensing range
warning. To incorporate this customiza-
tion, please contact an D X W K R U L V H G 0 D U X W L
6 X ] X N L Z R U N V K R S
• If the battery of the remote controller is
about to become completely discharged,
the corresponding message will appear
on the information display when you
press the engine switch to change the
ignition mode to ON. Refer to “Informa-
tion Display” in the “BEFORE DRIVING”
section for details. For details on replac-
ing the battery, refer to the “Keyless
Push Start System Remote Controller” in
the “BEFORE DRIVING” section.
(OFF)
ON ACC LOCK
(Audio equipment)
( ; $ 0 3 / (
(1)