2015 SMART FORTWO COUPE lock

X
Thread top tether strap Athrough top
tether guide :down the back of
passenger seat ;to top tether anchor-
age =.
X Attach top tether hook ?to top tether
anchorage =on the floor of the cargo
compartment.
i If you are using divider plus*, the
hooks of the top tether and the divider
plus* are attached to the same anchorage.
X Install the child restraint system and
tighten top tether strap Aaccording to
the child restraint manufacturer’s
instructions. G
WARNING
After installing top tether straps, make
sure the seat backrests are in an upright
position and are properly locked. Push and pull on the seat backrests to ensure they are
properly secured in the locked position. If
a seat backrest is not properly locked, the
seat backrest could fold. The child seat
would no longer be properly supported or
positioned to provide its intended bene-
fit. That could cause serious or even fatal
injuries. Panic alarm X
Activating: Press and hold button :for
at least 1 second.
An audible alarm and flashing exterior
lamps will operate briefly.
X Deactivating: Press button:once more.
or
X Insert the key in the starter switch.
i USA only:
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful
interference, and
2. this device must accept any interfer-
ence received, including interference
that may cause undesired operation.
Any unauthorized modification to this
device could void the user’s authority to
operate the equipment.
The product label with FCC ID and IC cer- tification number can be found in the
battery case.
i Canada only:
This device complies with RSS‑210 of
Industry Canada. Operation is subject to
the following two conditions:
1. This device may not cause interfer-
ence, and
2. this device must accept any interfer-
ence received, including interference
that may cause undesired operation of
the device.
Any unauthorized modification to this
device could void the user’s authority to
operate the equipment.
The product label with FCC ID and IC cer-
tification number can be found in the
battery case. Panic alarm
45>> Safety.
* optional Z

Driving safety systems
Introduction
G
WARNING
The following factors increase the risk of
accidents:
R Excessive speed, especially in turns
R Wet and slippery road surfaces
R Following another vehicle too closely
The driving safety systems described in
this section cannot reduce these risks or
prevent the natural laws of physics from
acting on the vehicle.
Always adapt your driving style to the pre- vailing road and weather and traffic con-
ditions and keep a safe distance to other
road users and objects on the street.
i In winter operation, the maximum
effectiveness of the ABS, the hydraulic
brake assistant, and the ESP ®
is only ach-
ieved with winter tires (Y page 146) or
snow chains* as required. Antilock Brake System (ABS)
G
WARNING
Do not pump the brake pedal. Use firm,
steady brake pedal pressure instead. Pump- ing the brake pedal defeats the purpose of
the ABS and significantly reduces braking
effectiveness.
The Antilock BrakeSystem (ABS) regulates
the brake pressure so that the wheels do not lock during braking. This allows you to
maintain the ability to steer your vehicle.
On slippery road surfaces, the ABS will
respond even to light brake pressure.
The ABS indicator lamp in the instrument
cluster (Y page 24) comes on when you
switch on the ignition. It goes out when the drive system is active. Braking At the instant one of the wheels is about to
lock up, a slight pulsation can be felt in the
brake pedal, indicating that the ABS is
regulating the brake pressure.
X Keep firm and steady pressure on the
brake pedal while experiencing the pul-
sation.
Continuous, steady brake pedal pressure
yields the advantages provided by the ABS,
namely braking power and the ability to
steer the vehicle.
A pulsating brake pedal can be an indica-
tion of hazardous road conditions and
functions as a reminder to take extra care
while driving.
Emergency brake maneuver X
Keep continuous full pressure on the
brake pedal. G
WARNING
When the ABS is malfunctioning, the
hydraulic brake assistant and the ESP ®
are
also switched off.
When the ABS is malfunctioning, the wheels may lock during hard braking, reducing
steering capability and extending the
braking distance. G
WARNING
The ABS cannot prevent the natural laws of
physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the
vehicle brakes and tires or the traction
afforded. The ABS cannot prevent acci-
dents, including those resulting from
excessive speed in turns, following
another vehicle too closely, or hydroplan-
ing. Only a safe, attentive, and skillful
driver can prevent accidents. The capabil- ities of an ABS equipped vehicle must never
be exploited in a reckless or dangerous 46
Driving safety systems>> Safety.
* optional

assistant automatically provides full
brake boost, thereby potentially reducing
the braking distance.
X Apply continuous full braking pressure
until the emergency braking situation is
over.
The ABS will prevent the wheels from
locking.
When you release the brake pedal, the
brakes function again as normal. The
hydraulic brake assistant is then deacti-
vated. G
WARNING
When the hydraulic brake assistant is mal-
functioning, the brake system is still func- tioning normally, but without the addi-
tional brake boost that would normally be
provided during an emergency braking
maneuver. Therefore, the braking distance
may increase. G
WARNING
The hydraulic brake assistant cannot pre-
vent the natural laws of physics from acting on the vehicle, nor can it increase braking
efficiency beyond that afforded by the con-
dition of the vehicle brakes and tires or the traction afforded. The hydraulic brake
assistant cannot prevent accidents,
including those resulting from excessive
speed in turns, following another vehicle
too closely, or hydroplaning. Only a safe,
attentive, and skillful driver can prevent
accidents. The capabilities of a hydraulic
brake assistant equipped vehicle must
never be exploited in a reckless or dan-
gerous manner which could jeopardize the
user’s safety or the safety of others. Activating the hazard warning flasher
after an emergency braking maneuver
If you bring the vehicle to a complete stop
by strongly braking at a speed of more than
43 mph (70 km/h), the hazard warning
flasher comes on automatically as soon as the vehicle is at a standstill. The hazard
warning flasher will remain on until it is
switched off using the hazard warning
flasher switch (Y
page 68) or until the
speed of the vehicle has exceeded 6 mph
(10 km/h). Acoustic Vehicle Indication*
Vehicles with electric motors develop con-
siderably lower driving noises than vehi-
cles with combustion engines. Therefore
your vehicle in traffic might not be acous-
tically noticed by other road users in cer- tain situations.
In order to avoid this, a built-in sound
generator emits a certain noise (Acoustic
Vehicle Indication) within a speed range
between 0 to 20 mph (30 km/h). Thus, other
road users, especially pedestrians and
bicycle riders can notice your vehicle bet-
ter. Acoustic Vehicle Indication can also
be heard inside of the vehicle.
The volume of Acoustic Vehicle Indication depends on the current engine speed (rpm).The stronger you accelerate, the louder thenoise. At speed of more than 20 mph 30 km/h
the noise is switched off. From this speed
on the natural noises of the vehicle are
sufficient so that other road users can
notice the vehicle on time. Anti-theft systems
Electronic immobilizer
The electronic immobilizer prevents
unauthorized persons from starting your
vehicle.
When leaving the vehicle, always take the
key with you and lock the vehicle. The drive
system can be switched on by anyone with a
key that is left inside the vehicle. 48
Anti-theft systems>> Safety.
* optional

X
Activating: Remove the key from the
starter switch.
X Deactivating: Insert the key in the
starter switch.
X Turn the key to starter switch position 1.Anti-theft warning system*
Once the anti-theft warning system has
been armed, a visual and audible alarm is
triggered when
R someone opens a door or the tailgate
R someone enters the vehicle’s interior
R there is motion inside the vehicle
R someone attempts to raise the vehicle
The alarm will also be triggered when
unlocking and opening the driver’s door
with the key.
i The alarm will stay on, even if the
driver’s door is immediately closed. For
canceling the alarm, see (Y page 49).
Close the windows and the tailgate before
arming the alarm system. Make sure there
are no moving objects inside the vehicle. X
Arming: Lock the vehicle using the
remote control.
Warning system indicator lamp :
flashes rapidly. The anti-theft warning
system arms after about 25 seconds. When the anti-theft warning system is armed, warning system indicator lamp
:
flashes about every three seconds.
i You can also arm the anti-theft warning
system by locking the vehicle without
using the remote control (Y page 177).
X Disarming: Unlock the vehicle using the
remote control.
The anti-theft warning system is dis-
armed. Warning system indicator
lamp :stops flashing.
Canceling the alarm X
Insert the key in the starter switch.
X Turn the key to starter switch position 1.
or
X Press button #or* on the key. Tow-away alarm* and interior motion
sensor*
Once the anti-theft warning system has
been armed, a visual and audible alarm is
triggered when someone attempts to raise
the vehicle or if motion is detected inside
the vehicle.
X Arming: Lock the vehicle using the
remote control.
The tow-away protection and the interior motion sensor are armed after about
25 seconds.
X Disarming: Unlock the vehicle using the
remote control.
The tow-away protection and the interior
motion sensor are disarmed.
Canceling the alarm X
Insert the key in the starter switch.
X Turn the key to starter switch position 1.
or
X Press button #or* on the key. Anti-theft systems
49>> Safety.
* optional Z

Switching off tow-away protection and
interior motion sensor Switch off the tow-away protection and the
interior motion sensor when locking the
vehicle and
R transporting the vehicle,
R board, e.g. a ferry or auto train,
R there are people or animals in the vehi-
cle,
R the side windows remain open.
This prevents any false alarm. X
Remove the key from the starter switch.
X Press switch :within 60 seconds.
Indicator lamp ;comes on.
X Exit the vehicle.
X Lock the vehicle using the remote con-
trol.
i The tow-away protection and the inte-
rior motion sensor remain switched off
until you lock your vehicle again. 50
Anti-theft systems>> Safety.

Opening and closing
Key
Key with remote control
:
*Lock button
; $Opening the retractable soft top 3
/
unlocking the upper tailgate 4
= #Unlock button
The remote control centrally locks and
unlocks:
R the driver’s door
R the charge socket flap
R the passenger door
R the upper tailgate G
WARNING
When leaving the vehicle, always remove the key from the starter switch, take it with
you, and lock the vehicle. Do not leave chil- dren unattended in the vehicle, or with
access to an unlocked vehicle. It is possi-
ble for children to open a locked door from
the inside, which could result in an acci-
dent and/or serious personal injury.
! To prevent possible malfunction, avoid
exposing the remote control to high lev-
els of electromagnetic radiation.
If you can no longer lock or unlock the vehi- cle with the remote control, the batteries
in the remote control are discharged, or
the remote control is malfunctioning. X
Check the batteries in the remote control
and replace them if necessary.
X If you do not have a spare transmitter
battery at hand, use the key to open the
driver’s door and the charge socket flap
(Y page 177).
i USA only:
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful
interference, and
2. this device must accept any interfer-
ence received, including interference
that may cause undesired operation.
Any unauthorized modification to this
device could void the user’s authority to
operate the equipment.
The product label with FCC ID and IC cer- tification number can be found in the
battery case.
i Canada only:
This device complies with RSS‑210 of
Industry Canada. Operation is subject to
the following two conditions:
1. This device may not cause interfer-
ence, and
2. this device must accept any interfer-
ence received, including interference
that may cause undesired operation of
the device.
Any unauthorized modification to this
device could void the user’s authority to
operate the equipment.
The product label with FCC ID and IC cer-
tification number can be found in the
battery case.
! The remote control has an operating
range of approximately 50 ft (15 meters).
This can fluctuate greatly as a conse-
quence of local conditions (reflective or
3 cabriolet only.
4 coupé only. 52
Opening and closing>> Controls.

absorbing objects) and interference
emitted by other radio transmission sys- tems. Similarly, the operating range
fluctuates in line with the direction
from which the remote control is activa-
ted.
To prevent theft, however, it is advisable to only unlock the vehicle when you are inclose proximity to it. Locking and unlocking from the out-
side
X Selective unlocking: Press button#on
the key once.
All turn signal lamps flash once.
The driver’s door and the charge socket
flap are unlocked.
X Global unlocking: Press button#on the
key twice.
All turn signal lamps flash once again.
The passenger door and the tailgate are
unlocked in addition to the driver’s door
and the charge socket flap.
X Global locking: Press button*on the
key.
With the doors, the tailgate(s), and the
charge socket flap closed, the turn sig-
nal lamps flash three times.
The indicator lamp on the central lock-
ing switch flashes (Y page 53).
The interior lamps come on and then go
out again after 12 seconds. Automatic locking
Auto-relock function The vehicle will lock again automatically
within approximately 60 seconds of
unlocking with the key if neither the
driver’s nor passenger door is opened.
! To prevent an inadvertent lockout,
never leave your key lying in the vehicle. Drive lock function The vehicle locks automatically when the
ignition is switched on and the wheels are
turning at vehicle speeds of approximately
8 mph (14 km/h) or more. The drive lock
function is enabled at the factory.
X Switching on: Switch off the ignition.
X Press the central locking switch
(Y page 53) and button *on the key
simultaneously.
An acoustic signal sounds.
The drive lock function is switched on.
X Switching off: Switch off the ignition.
X Press the central unlocking switch
(Y page 53) and button #on the key
simultaneously.
An acoustic signal sounds.
The drive lock function is switched off. Locking and unlocking from the inside
G
WARNING
When leaving the vehicle, always remove the key from the starter switch, take it with
you, and lock the vehicle. Do not leave chil- dren unattended in the vehicle, or with
access to an unlocked vehicle. A child’s
unsupervised access to a vehicle could
result in an accident and/or serious per-
sonal injury.
You can lock and unlock the vehicle from
inside using the central locking or unlock-
ing switch. This can be useful, for example,
if you want to unlock the passenger door
from inside or lock the vehicle before
starting to drive. Opening and closing
53>> Controls. Z

X
Locking: Press central locking
switch :.
The indicator lamp on central locking
switch :comes on, when the starter
switch is in position 1.
The indicator lamp on central locking
switch :flashes, when the starter
switch is in position 0.
With the doors and the tailgate closed,
the vehicle locks.
X Unlocking: Press central unlocking
switch ;.
The vehicle unlocks and the indicator
lamp on central locking switch :goes
out. Opening the doors from the inside
You can open a locked door from the inside.
Open door only when conditions are safe to do so. X
Pull on inside door handle :.
With the driver’s door open a warning
signal sounds if the exterior lamps are switched on and the ignition is switched
off. Opening the upper tailgate on the
coupé
X
Press button #on the key twice.
X Press and hold button $on the key for
approximately two seconds.
or
X Pull the release handle in handle
recess :of the lower tailgate.
The upper tailgate is unlocked.
X Swivel the upper tailgate upwards to
open.
Observe the information on loading the
vehicle (Y page 108).
For information on vehicle weights, see
“Vehicle specification” (Y page 215). Opening the lower tailgate on the
coupé
X Open the upper tailgate (Y page 54).54
Opening and closing>> Controls.