2015 Seat Altea ignition

Advice
●
At continuously high speeds, a tyre with in-
sufficient pressure flexes more. In this way it
becomes too hot, and this can cause tread
separation and tyre blow-out. Always observe
the recommended tyre pressures.
● If the tyre pressure is too low or too high,
the tyres will wear prematurely and the vehi-
cle will not handle well. Risk of accident! For the sake of the environment
Under-inflated tyres will increase fuel con-
sumption. Tyre pressure monitoring
The tyre pressure monitoring system con-
stantly checks the pressure of the tyres.
The system uses the speed sensors of the
ABS wheels. It operates by analysing the
speed and frequency spectrum of each
wheel.
For optimum performance, use genuine SEAT
tyres. In addition, check and adjust tyre pres-
sures regularly.
Whenever the tyre pressure is are changed or
one or more tyres are changed, the system
should be reset by pressing the SET button
on the centre console.
The system warns the driver in the event of a
loss of pressure by means of symbols and messages in the instrument panel display.
The system operates via the ESC
››› page 134.
Note that tyre pressure also depends on tyre
temperature. Said pressure increases around
0.1 bar (2.9 psi/10 kPa) for each +10 °C
(+50 °F) in tyre temperature increase. The tyre
heats up while the vehicle is being driven
and the tyre pressure will rise accordingly.
Therefore, you should only adjust the tyre
pressure when they are cold (i.e. approxi-
mately at ambient temperature).
To ensure that the tyre pressure monitoring
system works reliably, you should check and,
if necessary, adjust the tyre pressures at reg-
ular intervals and store the correct pressures
(reference values) in the system.
A tyre pressure information label is attached
to the inside of the fuel tank flap. WARNING
● Never adjust tyre pressure when the tyres
are hot. This may damage or even burst the
tyres. Risk of accident!
● An insufficiently inflated tyre flexes a lot
more at high speeds and causes significant
heating of the tyre. Under these conditions,
the tyre bead may be released or the tyre may
burst. Risk of accident! For the sake of the environment
Under-inflated tyres lead to increased fuel
consumption and tyre wear. Significant tyre pressure loss
The tyre symbol
 is displayed and indicates
th at
the tyre pressure of at least one tyre is
insufficient.
– Stop the vehicle.
– Switch the ignition off.
– Check the tyre(s).
– Change the wheel if necessary.
176

Advice
How to jump start: description Fig. 163
Diagram of connections for vehicles
without Start-Stop system. Fig. 164
Diagram of connections for vehicles
with Start-Stop system. Jump lead terminal connections
1. Switch off the ignition of both vehicles
››› . 2. Connect one end of the
red jump lead to
the po s
itive + terminal of the vehicle
with the flat battery A
››› Fig. 163 .
3. C

onnect the other end of the red
jump
lead to the positive terminal + in the ve-
hicle providing assistance B .
4. For vehicles without Start-Stop system:
connect one end of the black jump lead to
the negative terminal – in the vehicle
providing assistance B
››› Fig. 163 .
– For

vehicles with Start-Stop system: Con-
nect one end of the black jump lead X to a
suitable ground terminal, a solid piece of
metal in the engine block, or to the engine
block itself ››› Fig. 164.
5. Connect the other end of the black jump
lead X to a solid metal component bolted
to the engine block or to the engine block
itself of the vehicle with the flat battery.
Do not connect it to a point near the bat-
tery A .
6. Position the leads in such a way that they cannot come into contact with any moving
parts in the engine compartment.
Starting
7. Start the vehicle's engine with the boost- ing battery and let it run at idling speed.
8. Start the engine of the vehicle with the flat battery and wait 2 or 3 minutes until the
engine is “running”. Removing the jump leads
9. Before you remove the jump leads, switch
off the dipped beam headlights (if they
are switched on).
10.Turn on the heater blower and heated rear window in the vehicle with the flat battery.
This helps minimise voltage peaks which
are generated when the leads are discon-
nected.
11. When the engine is running, disconnect
the l e
ads in reverse order to the details
given above.
Connect the battery clamps so they have
good metal-to-metal contact with the battery
terminals.
If the engine fails to start, switch off the start-
er after about 10 seconds and try again after
about a minute. WARNING
● Please note the safety warnings referring to
working in the engine compartment
››› page 163, Working in the engine compart-
ment.
● The b att

ery providing assistance must have
the same voltage as the flat battery (12 V)
and approximately the same capacity (see
imprint on battery). Failure to comply could
result in an explosion.
● Never use jump leads when one of the bat-
teries is frozen. Danger of explosion! Even 190

Emergencies
after the battery has thawed, battery acid
could leak and cause chemical burns. If a bat-
tery freezes, it should be replaced.
●
Keep sparks, flames and lighted cigarettes
away from batteries, danger of explosion.
Failure to comply could result in an explo-
sion.
● Observe the instructions provided by the
manufacturer of the jump leads.
● Do not connect the negative cable from the
other vehicle directly to the negative terminal
of the flat battery. The gas emitted from the
battery could be ignited by sparks. Danger of
explosion.
● Do not attach the negative cable from the
other vehicle to parts of the fuel system or to
the brake line.
● The non-insulated parts of the battery
clamps must not be allowed to touch. The
jump lead attached to the positive battery
terminal must not touch metal parts of the ve-
hicle, this can cause a short circuit.
● Position the leads in such a way that they
cannot come into contact with any moving
parts in the engine compartment.
● Do not lean on the batteries. This could re-
sult in chemical burns. Note
The vehicles must not touch each other, oth-
erwise electricity could flow as soon as the
positive terminals are connected. Towing and tow-starting
Tow-starting We recommend that you do
not tow-start your
v ehic
le. Jump-starting is preferable
››› page 189.
How

ever, if your vehicle has to be tow-
started:
– Engage 2 nd
or 3 rd
gear.
– Keep the clutch pressed down.
– Switch the ignition on.
– Once both vehicles are moving, release the
clutch.
– As soon as the engine starts, press the
clutch and move the gear lever into neutral.
This helps to prevent driving into the tow-
ing vehicle. WARNING
The risk of accidents is high when tow-start-
ing. The vehicle being towed can easily col-
lide with the towing vehicle. CAUTION
When tow-starting, fuel could enter the cata-
lytic converter and damage it. General notes
Please observe the following points if you
use a tow rope:
Notes for the driver of the towing vehicle
– Drive slowly at first until the tow rope is
taut. Then accelerate gradually.
– Begin and change gears cautiously. If you
are driving an automatic vehicle, accelerate
gently.
– Remember that the brake servo and power
steering are not working in the vehicle you
are towing. Brake sooner than normal and
pressing the pedal gently.
Notes for the driver of the towed vehicle
– Ensure that the tow rope remains taut at all
times when towing.
Tow rope or tow bar
It is easier and safer for the vehicle to be tow-
ed using a tow bar. You should only use a
tow-rope if you do not have a tow-bar.
A tow rope should be slightly elastic to re-
duce the loading on both vehicles. It is advis-
able to use a tow rope made of synthetic fi-
bre or similarly elastic material.
Attach the tow rope or the tow bar only to the
towline anchorages provided or a towing
bracket. »
191Technical specifications
Advice
Operation
Safety

Advice
Driving style
Towing requires some experience, especially
when using a tow rope. Both drivers should
be familiar with the technique required for
towing. Inexperienced drivers should not at-
tempt to tow.
Do not pull too hard with the towing vehicle
and take care to avoid jerking the tow rope.
When towing on an unpaved road, there is al-
ways a risk of overloading and damaging the
anchorage points.
The ignition of the vehicle being towed must
be switched on to prevent the steering wheel
from locking and also to allow the use of the
turn signals, horn, windscreen wipers and
washers.
The brake servo only works when the engine
is running. When not running, you must ap-
ply considerably more pressure to the brake
pedal.
As the power assisted steering does not work
if the engine is not running, you will need
more strength to steer than you normally
would.
● The vehicle must not be towed faster than
50 km/h (31 mph).
Towing vehicles with an automatic gearbox
● Put the selector lever into position “N”.
● Do not drive faster than 50 km/h (31 mph). ●
Do not tow further than 50 km.
● If a breakdown vehicle is used, the vehicle
must be towed with the front wheels raised. Note
● Observe legal requirements when towing or
tow-starting.
● Switch on the hazard warning lights of both
vehicles. However, observe any regulations
to the contrary.
● For technical reasons, vehicles with an au-
tomatic gearbox must not be tow-started.
● If there is no lubricant in the gearbox as the
result of a fault, you must raise the driven
wheels while the vehicle is being towed.
● If the vehicle has to be towed more than
50 km, the front wheels should be raised dur-
ing towing, and towing should be carried out
by a qualified person.
● The steering wheel is locked when the vehi-
cle has no electrical power. The vehicle must
then be towed with the front wheels raised.
Towing should be carried out by a qualified
person.
● The towline anchorage should always be
kept in the vehicle. Please refer to the notes
on ››› page 191, Tow-starting. Towline anchorages
Fig. 165
Fitting the front towline anchorage
to the front right section of the vehicle. Fig. 166
Fitting the towline anchorage to the
rear of the vehicle. Front towline anchorage
– Take the towline anchorage from the on-
board tool set.
– Remove the cover by pressing down on its
left-hand side.
192

Advice
Emergency boot hatch opening Fig. 168
Rear lid: emergency opening. This allows the vehicle to be opened if the
central locking does not work (for example, if
the battery is flat)
There is a groove in the luggage compart-
ment allowing access to the emergency
opening mechanism.
Opening the rear lid from inside the luggage
compartment
– Insert the key in the groove and unlock the
locking system, turning the key from right
to left, as shown by the arrow ››› Fig. 168 .Ch
an ging the wiper blades
Changing windscreen wiper blades Fig. 169
Windscreen wipers in the service po-
sition. Fig. 170
Changing the windscreen wiper
blades Perfect wiper blade condition is essential for
clear vision. Damaged wiper blades should
be replaced immediately.To change the blades it is necessary to move
the wipers from the rest position into the
service position.
Service position (for changing wiper blades)
–
Ensure that the wiper blades are not frozen.
– Turn the ignition on and off and then (with-
in approximately 8 seconds), push the
windscreen wiper lever out of the short
wipe position. The windscreen wipers will
move to the service position.
Changing the windscreen wiper blades – Lift the wiper arm away from the wind-
screen.
– Push the side buttons, free the blade and
pull in the direction of the arrow ››› Fig. 170
Fitting the wiper blade
– Insert a blade of identical length and de-
sign into the wiper arm.
– Slide the blade until it clicks into position.
– Push the wiper arms back against the wind-
screen.
The windscreen wiper arms return to their
original position when the ignition is turned
on and the windscreen wiper lever is operat-
ed, or when driving faster than 6 km/h.
194

Fuses and bulbs
WARNING
The high voltages in the electrical system can
give serious electrical shocks, causing burns
and even death!
● Never touch the electrical wiring of the igni-
tion system.
● Take care not to cause short circuits in the
electrical system. WARNING
Using unsuitable fuses, repairing fuses or
bridging a current circuit without fuses can
cause a fire and serious injury.
● Never use a fuse with a higher value. Only
replace fuses with a fuse of the same amper-
age (same colour and markings) and size.
● Never repair a fuse.
● Never replace a fuse by a metal strip, staple
or similar. CAUTION
● To prevent damage to the vehicle's electric
system, before replacing a fuse turn off the
ignition, the lights and all electrical elements
and remove the key from the ignition.
● If you replace a fuse with higher-rating
fuse, you could cause damage to another part
of the electrical system.
● Protect the fuse boxes when open to pre-
vent the entry of dust or humidity as they can
damage the electrical system. Note
● One component may have more than one
fuse.
● Several components may run on a single
fuse. Vehicle fuses
Fig. 173
Left side of dash panel fuse box cov-
er Fig. 174
In the engine compartment: fuse box
cover Only replace fuses with a fuse of the same
amperage (same colour and markings) and
size.
Identifying fuses situated below the driver-
side dash panel by coloursColourAmp rating
Purple3
Light brown5
Brown7.5
Red10
Blue15
Yellow20
White or trans-
parent25
Green30» 197
Technical specifications
Advice
Operation
Safety

AdviceColourAmp rating
Orange40
Opening and closing the fuse box situated
below the dash panel
●
Opening: fold the cover down ››
› Fig. 173.
● Closing:
push back the cover it in until it
clicks into place.
To open the engine compartment fuse box
● Open the bonnet  ›››
page 163.
● Press the locking tabs in the direction indi-
cated by the arrows to release the fuse box
cover ›››
Fig. 174.
● Then lif t

the cover out.
● To
fit the cover, place it on the fuse box.
Push the locking tabs down, in the opposite
direction to that indicated by the arrows, un-
til you hear them click into place. CAUTION
● Always carefully remove the fuse box cov-
ers and refit them correctly to avoid problems
with your vehicle.
● Protect the fuse boxes when open to avoid
the entry of dust or humidity. Dirt and humid-
ity inside fuse boxes can cause damage to
the electrical system. Note
In the vehicle, there are more fuses than
those indicated in this chapter. These should
only be changed by a specialised workshop. Replacing a blown fuse
Fig. 175
Image of a blown fuse Preparation
● Switch off the ignition, lights and all elec-
trical equipment.
● Open the corresponding fuse box
››› page 197 .
Identif y

ing a blown fuse
A fuse is blown if its metal strip is ruptured
››› Fig. 175
.
Point a lamp at the fuse. This will make it
easier to see if the fuse is blown. To replace a fuse
● Remove the fuse.
● Replace the blown fuse by one with an
identical amperage rating (same colour and
mark

ings) and identical size ››› .
● Replace the cover again or close the fuse
box lid. CAUTION
If you replace a fuse with higher-rating fuse,
you could cause damage to another part of
the electrical system. Changing the lights
General notes Before changing any bulb, first turn off the
failed device.
Do not touch the glass part of the bulb with
your bare hands. The fingerprints left on the
glass will vaporise as a result of the heat gen-
erated by the bulb, reducing bulb life and
causing condensation on the reflector sur-
face, thus reducing effectiveness.
A bulb must only be replaced by one of the
same type. The type is indicated on the bulb,
either on the glass part or on the base.
It is highly recommended to keep a box of
spare bulbs in the vehicle. At the very least,
198

Index
Front drinks holders . . . . . . . . . . . . . . . . . . . . . . . . 95
Front interior light Switch off light . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Switch on light . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Front passenger airbag deactivation . . . . . . . . . . 23
Front reading lights . . . . . . . . . . . . . . . . . . . . . . . . 82
Front seat adjustment Lumbar support adjustment . . . . . . . . . . . . . . . 89
Fuel Diesel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
Petrol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
Fuel consumption . . . . . . . . . . . . . . . . . . . . 132, 208
Fuel level Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Fuel reserve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Warning message . . . . . . . . . . . . . . . . . . . . . . . . 49
Fuel tank see Fuel reserve . . . . . . . . . . . . . . . . . . . . . . . . . 40
F uel
Tank
Opening the fuel tank flap . . . . . . . . . . . . . . . . 158
Fuel: saving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196 Fuse box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197
Identifying blown fuses . . . . . . . . . . . . . . . . . . 198
Identifying by colours . . . . . . . . . . . . . . . . . . . . 197
Preparation before replacing . . . . . . . . . . . . . . 198
Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . 198
G Gear shift pattern . . . . . . . . . . . . . . . . . . . . . . . . . 126
General overview of the engine compartment . . 166
Glove compartment . . . . . . . . . . . . . . . . . . . . . . . . 93
Glow plug system . . . . . . . . . . . . . . . . . . . . . . . . . 122 Control lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 H
Handbrake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Control lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
warning lamp . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Hazard warning lights . . . . . . . . . . . . . . . . . . . . . . 81
HBA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Head-on collisions and the laws of physics . . . . . 13
Head-protection airbags . . . . . . . . . . . . . . . . . . . . 22 safety instructions . . . . . . . . . . . . . . . . . . . . . . . 22
Headlight flashers . . . . . . . . . . . . . . . . . . . . . . . . . 77
Headlight range control . . . . . . . . . . . . . . . . . . . . . 79
Headlights Driving abroad . . . . . . . . . . . . . . . . . . . . . . . . . 120
fog lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Headlight washer . . . . . . . . . . . . . . . . . . . . . . . . 86
Head restraints Adjusting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Adjustment of the head restraint angle . . . . . . 90
Correct adjustment . . . . . . . . . . . . . . . . . . . . . . . 90
Removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Heated front seats . . . . . . . . . . . . . . . . . . . . . . . . . 91
Heated rear window 2C-Climatronic . . . . . . . . . . . . . . . . . . . . . . . . . 113
heating element wires . . . . . . . . . . . . . . . . . . . 151
Heating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
High pressure cleaners . . . . . . . . . . . . . . . . . . . . 150
Hill driving assistant . . . . . . . . . . . . . . . . . . . . . . 125
Horn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
How to jump start description . . . . . . . . . . . . . . . 190
Hydraulic Brake Assist . . . . . . . . . . . . . . . . . . . . . 136
I Identification number . . . . . . . . . . . . . . . . . . . . . 208
Identification plate . . . . . . . . . . . . . . . . . . . . . . . . 208
Ignition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Ignition lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Information messages in the display . . . . . . . . . . 49 Information on the multi-function display
On-screen display . . . . . . . . . . . . . . . . . . . . . . . . 52
Instrument and switch lighting . . . . . . . . . . . . . . . 79
Instrument lighting . . . . . . . . . . . . . . . . . . . . . . . . 31
Instrument panel menu Lights and visibility menu . . . . . . . . . . . . . . . . . 56
Instrument panel menus Configuration menu . . . . . . . . . . . . . . . . . . . . . . 54
Example of menu use . . . . . . . . . . . . . . . . . . . . . 50
Main menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Vehicle status menu . . . . . . . . . . . . . . . . . . . . . . 54
Instruments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Interior lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Interior monitoring . . . . . . . . . . . . . . . . . . . . . . . . . 70 Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Deactivation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Interior rear vision mirror . . . . . . . . . . . . . . . . . . . . 86
Intermittent windscreen wipe . . . . . . . . . . . . . . . . 84
ISOFIX system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
J Jack position points Sill panel trim . . . . . . . . . . . . . . . . . . . . . . . . . . 185
Journeys abroad . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Jump-starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189
Jump leads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189
K
Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
L
Lifting the seat backrest . . . . . . . . . . . . . . . . . . . . 92
Lifting the vehicle . . . . . . . . . . . . . . . . . . . . . . . . . 185
Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 general remarks . . . . . . . . . . . . . . . . . . . . . . . . 198
Load compartment in the luggage compartment see Loading the luggage compartment . . . . . 101
226