2015 Peugeot RCZ instrument panel

23
RCZ_en_Chap01_controle-de-marche_ed01-2015
SERVICE INdICATOR
This information is displayed for a few seconds when the ignition is
switched on. It informs the driver when the next service is due, in
accordance with the manufacturer's service schedule.
The point at which the service is due is calculated from the last indica\
tor
zero reset. It is determined by two parameters:
-
the distance travelled,
-


the time elapsed since the last service (only on HDi Diesel
versions).
More than 1 800 miles (3 000 km) remain before the next service is due\
When the ignition is switched on, no service information appears on the \
instrument panel central screen.
Between 600 miles (1 000 km) and 1 800 miles (3 000 km)
remain before the next service is due
For a few seconds after the ignition is switched on, the spanner
symbolising the service operations comes on. The instrument panel central
screen indicates the distance remaining before the next service is due.
Example: 1 700 miles (2 800 km) remain before the next service is due.
For a few seconds after the ignition is switched on, the central screen
indicates:
Less than 600 miles (1 000 km) remain before the next service is due
Example: 500 miles (900 km) remain before the next service is due.
For a few seconds after the ignition is switched on, the central screen \
indicates:
The spanner remains on in the small screen
to indicate that a service must be carried out
soon.
1/
MONITORING

24
RCZ_en_Chap01_controle-de-marche_ed01-2015
Service overdue
For a few seconds after the ignition is switched on, the spanner
flashes to indicate that the service must be carried out as soon as
possible.
Example: the service is overdue by 300 miles (300
km).
For a few seconds after the ignition is switched on, the central screen \
indicates:
The spanner remains on in the small screen
to indicate that a service should have been
carried out.
The distance remaining may be weighted by the time factor,
depending on the type of motoring the vehicle is used for.
Therefore, the spanner may also come on if you have exceeded
the
period since the last service specified in the manufacturer's
service schedule.
This indication applies only to HDi Diesel engines.
Service indicator reset
Retrieving the service information
You can access the service information at any time.
This information appears when running through the manual check
procedure.
F Briefly press the "CHECK/000" button.
The service information is displayed for a few seconds on the
instrument panel central screen, then disappears.
Following this operation, if you wish to disconnect the battery

,
lock the vehicle and wait at least five minutes for the reset to be
registered.
After each service, the service indicator must be reset.
If you have carried out the service on your vehicle yourself:
F

switch of
f the ignition,
F
press and hold the
"CHECK/000" button,
F

switch on the ignition; the distance recorder display begins a
countdown,
F

when the instrument panel central screen indicates
"=0"
, release
the button; the spanner disappears from the small screen.

25
RCZ_en_Chap01_controle-de-marche_ed01-2015
MANUAL CHECK
This function allows you to check the status of the vehicle (reminder o\
f
the active alert warnings) and the service information.
F With
the engine running, to start a manual check, briefly press the
"CHECK/000" button on the instrument panel.
If no faults have been detected,

"CHECK OK" appears in the
instrument panel central screen.
If a "minor" fault has been detected, the warning lamp concerned then
"CHECK OK" appear in the instrument panel central screen. Contact a
PEUGEOT


or a qualified workshop.
If a "major" fault has been detected, only the warning lamps concerned
appear in the instrument panel central screen. Have it checked by a
PEUGEOT


dealer or a qualified workshop.
dISTANCE RECORdERS
The total and trip distances are displayed for thirty seconds when the
ignition is switched off, when the driver's door is opened and when the
vehicle is locked or unlocked.
Measures the total distance travelled by the vehicle since its first
registration.
Total distance recorder
F With the ignition on, press and hold this button until zeros appear .
Trip distance recorder
Measures the distance travelled since it was last reset to zero by the
driver.
1/
MONITORING

27
RCZ_en_Chap01_controle-de-marche_ed01-2015
display of information
F Cycle through the information with successive short presses on this
button.
TRIP COMPUTER
CENTRAL INSTRUMENT PANEL SCREEN
C

ENTRAL

INSTRUMENT PANEL

SCREEN WITH
NA

VIGATION
System that gives you information on the current journey (range, fuel
consumption…).
1/
MONITORING

76
RCZ_en_Chap04_visibilite_ed01-2015
Model without AUTO lightingModel with AUTO lighting
MANUAL CONTROLS
The lighting is controlled directly by the driver by means of the ring A
and the stalk B.
A.

Main lighting mode selection ring: turn it to position the symbol
required

facing the mark.
Lighting off / daytime running lamps.
Automatic illumination of headlamps.
B.

Stalk for switching headlamps: pull it to switch between dipped
headlamps / main beam headlamps.
In the lamps of

f and sidelamps modes, the driver can switch on the
main
beam headlamps temporarily ("headlamp flash") by maintaining a
pull on the stalk.Sidelamps only

.
Dipped or main beam headlamps.
dISPLAYS
Lighting of the corresponding indicator lamp on the instrument panel
confirms the switching on of the lighting selected.
The instrument panel has permanent back-lighting, both day and night.
In this case, illumination of the instrument panel is not linked to the \
exterior lighting.

80
RCZ_en_Chap04_visibilite_ed01-2015
AUTOMATIC GUId E - ME - HOME
LIGHTING
Operating fault
In the event of a malfunction of the sunshine sensor, the
lighting comes on, this warning lamp is displayed in the
instrument panel and/or a message appears in the screen,
accompanied by an audible signal.
Contact

a

PEUGEOT

dealer or a qualified workshop.
In

fog

or snow, the sunshine sensor may detect sufficient light. In
this case, the lighting will not come on automatically

.
Do not cover the sunshine sensor, coupled with the rain sensor
and located in the centre of the windscreen behind the rear view
mirror; the associated functions would no longer be controlled. When the automatic illumination of headlamps function is activated
(lighting control stalk in the "
AUTO" position), under low ambient light
the dipped beams headlamps come on automatically when the ignition
is switched off.
Programming
Activation or deactivation, as well as the duration of the guide-me-home\

lighting, is set in the vehicle configuration menu.

81
RCZ_en_Chap04_visibilite_ed01-2015
MANUAL AD j USTMENT OF
HALOGEN

HEADLAMPSA UTOMATIC AD j USTMENT OF
xENON

HEADLAMPS
To avoid dazzling other road users, the height of the halogen bulb
headlamps must be adjusted according to the load in the vehicle.
0.

1 or 2 people in the front seats.
-.


3 people.
1.


4 people.
-.


Intermediate setting.
2.


4 people + maximum authorised loads.
-.


Intermediate setting.
3.


Driver + maximum authorised loads. In order to avoid causing a nuisance to other road users, this system
corrects the height of the xenon headlamp beams automatically and
when stationary

, in relation to the load in the vehicle.
If a malfunction occurs, this warning lamp is displayed on the
instrument panel, accompanied by an audible signal and a
message in the screen.
The system then places your headlamps in the lowest position.
Initial setting is position "0". Do not touch the xenon headlamp bulbs.
Contact
a PEUGEOT

dealer or a qualified workshop.
Travelling abroad
If using your vehicle in a country that drives on the other side of
the road, the headlamps must be adjusted to avoid dazzling on-
coming drivers.
Contact
a PEUGEOT

dealer or a qualified workshop.
4/
VISIBILITY

82
RCZ_en_Chap04_visibilite_ed01-2015
DIRECTIONAL LIGHTING
When the dipped or main beam headlamps are on, this function enables
the light beams to provide improved lighting of the side of the road when
cornering.
The use of this function, from approximately 12 mph (20 km/h) and
associated with the xenon headlamps only, considerably improves the
quality
of your lighting when cornering.
with directional lighting
without directional lighting
PROGRAMMING
O
PERATING
F
AULT
When stationary or moving at very low speed or when reverse
gear is engaged, the function is inactive.
The status of the function remains in the memory when the
ignition is switched off.If
a fault occurs, this warning lamp flashes in the instrument
panel, accompanied by a message in the screen.
Contact

a PEUGEOT

dealer or a qualified workshop.
The function is activated or deactivated via the vehicle
configuration menu.