2015 Peugeot iOn Owner's Manual

103
Ion_en_Chap08_info-pratiques_ed01-2014
F Remove the bolts and store them in a clean place.
F

R
emove the wheel. Ensure that the jack is stable. If the
ground is slippery or loose, the jack
might slip or drop - Risk of injury!
Take care to position the jack only at
one of the vehicle’s jacking points A
or B under the vehicle, ensuring that the
contact sur face of the vehicle’s jacking
point is centred on the head of the jack.
Otherwise there is a risk of damage to
the vehicle and/or that the jack might
drop - Risk of injury!
8
Practical information

104
Ion_en_Chap08_info-pratiques_ed01-2014
Fitting a wheel
F Put the wheel in place on the hub.
F S crew in the bolts by hand.
F

P
re-tighten the bolts using the wheelbrace. F
L ower the vehicle fully.
F F old the jack and detach it.F
T ighten the bolts using the wheelbrace.
After changing a wheel
Have the tightness of the bolts and the
tyre pressure of the new wheel checked
by a PEUGEOT dealer or a qualified
workshop without delay.
Practical information

105
Ion_en_Chap08_info-pratiques_ed01-2014
Snow chains
The snow chains must be fitted only to the rear wheels (vehicle with rear wheel drive).It is strongly recommended that before
you leave, you practise fitting the snow
chains on a level and dry sur face. Take account of the legislation in force
in your country on the use of snow
chains and the maximum running speed
authorised. For more information on snow chains,
contact a PEUGEOT dealer or a
qualified workshop.Avoid driving with snow chains on roads
that have been cleared of snow, to
avoid damaging your vehicle's tyres and
the road sur face. If your vehicle is fitted
with alloy wheels, check that no part of
the chain or its fixings is in contact with
the wheel rim.Advice on installation
F If you have to fit the chains during a
journey, stop the vehicle on a flat sur face
on the side of the road.
F

A
pply the parking brake and position any
wheel chocks to prevent movement of your
vehicle.
F

F
it the chains following the instructions
provided by the manufacturer.
F

M
ove off gently and drive for a few
moments, without exceeding 30 mph
(50 km/h).
F

S
top your vehicle and check that the snow
chains are correctly tightened.
Use only the chains designed to be fitted to the
type of wheel fitted to your vehicle:
Original
tyre size Maximum link
size.
175 / 5 5 R15 9 mm
145/65 R15
cannot be fitted with chains
8
Practical information

106
Ion_en_Chap08_info-pratiques_ed01-2014
Changing a bulb
1. Direction indicators (W21W - 21 W).
2. S idelamps (W5W - 5 W).
3.
M

ain beam headlamps (HB3 - 60 W).
4.
D

ipped beam headlamps (H11 - 55 W).
The headlamps are fitted with
polycarbonate glass with a protective
coating:
F

d

o not clean them using a dr y
or abrasive cloth, nor with a
detergent or solvent product,
F

u

se a sponge and soapy water or a
pH neutral product,
F

w

hen using a high pressure washer
on persistent marks, do not keep
the lance directed towards the
lamps or their edges for too long,
so as not to damage their protective
coating and seals.
Changing a bulb should only be done
after the headlamp has been switched
off for several minutes (risk of serious
burns).
F

D

o not touch the bulb directly with
your fingers, use a lint-free cloth.
It is imperative to use only anti-
ultraviolet (UV) type bulbs to avoid
damaging the headlamp.
Always replace a failed bulb with a
new bulb with the same type and
specification.
Front lamps
5. Front foglamps (H8 - 35 W).
6. D aytime running lamps
(P13W - 13 W).
Practical information

107
Ion_en_Chap08_info-pratiques_ed01-2014
F Lift the cover B, using a screwdriver
protected by a cloth.
F

S
lacken fixing screw C until the head of the
screw touches the trim. F
R emove the bumper retaining clips, using a
screwdriver.
F

C
arefully lift the bumper.
To replace a failed bulb, you must first remove
the lamp.
To remove the lamp:
F

O

pen the bonnet.
F

P

ress tab A to release the connector.
Access to bulbs
8
Practical information

108
Ion_en_Chap08_info-pratiques_ed01-2014
F Slacken fixing screw D, while holding the
b um p e r away.
F

S
lacken fixing screw E . F
P ull the lamp towards you, and disengage
the tab F to remove it completely.
Practical information

109
Ion_en_Chap08_info-pratiques_ed01-2014
Changing sidelamp bulbs
F Turn the bulb holder to the left and pull it out.
F

P
ull the bulb out and and change it.
To reassemble, carry out these operations in
reverse order.
Changing main beam headlamp
bulbs
F Turn the bulb holder to the left and pull it out.
F R emove the bulb by pressing on the
tongue.
F

C
hange the bulb.
For reassembly, carry out these operations in
reverse order.
Changing direction indicator
bulbs
F Turn the bulb holder to the left and pull it out.
F

P
ull the bulb out and change it.
To refit, carry out these operations in reverse
o r d e r.
Amber coloured bulbs must be replaced
with bulbs of identical specifications
and colour.
8
Practical information

110
Ion_en_Chap08_info-pratiques_ed01-2014
Changing dipped beam headlamp
bulbs
F Turn the bulb holder to the left and pull it out.
F R emove the bulb by pressing on the
tongue.
F

C
hange the bulb.
To refit, carry out these operations in reverse
o r d e r.
Changing front foglamp bulbs /
daytime running lamp bulbs
F Put the front wheels onto full lock, to facilitate access.
F

R
emove the clips securing the protective
covers on the bulb holders.
F

M
ove the cover aside. F
T urn the bulb holder (A for the front fog
lamp, B for the daytime running lamp) to
the left and pull it out.
F

P
ull the bulb out and change it.
To reassemble, carry out these operations in
reverse order.
Practical information