2015 Peugeot 208 ESP

Driving141
208_en_Chap06_conduite_ed01-2016
The laser beam is invisible. Never
look at the laser sensor through an
optical instrument (magnifying glass,
microscope...): risk of eye injury.
Active City Brake
A preventive driving assistance system
that, using a sensor located at the top of the
windscreen, automatically applies the vehicle's
brakes if driving behind a vehicle that is slowing
down rapidly, stopping or is stationary.
The objective is to avoid a collision or reduce
the speed of impact.
This system is designed to improve driving
safety.
It remains the driver's responsibility to
continuously monitor the state of the traffic and
to assess the distances and relative speeds of
other vehicles.The Active City Brake system can in
no circumstances replace the need for
vigilance on the part of the driver. If operation is triggered:
-

D
isplay of a message.
-

I
llumination of the brake lamps.
The automatic braking is triggered as a last
resort, if the driver fails to apply the brakes
sufficiently firmly or at all, or to take avoiding
action. When your vehicle is too close to or
approaches the vehicle ahead too quickly, the
system automatically applies the brakes to
avoid a collision. Conditions for operation:
-

V
ehicles driving in the same lane.
- N ot in too sharp a bend.
- S peed of your vehicle between 3 and
18 mph (5 and 30 km/h).
-

B
raking assistance systems (ABS, EBFD,
EBA) in working order.
-

T
rajectory control systems (ASR, DSC) in
working order and not deactivated.
-

O
peration of Active City Brake not
triggered in the previous 10 seconds.
6

Driving
146
208_en_Chap06_conduite_ed01-2016
Reversing camera
The reversing camera function may be
completed with parking sensors. The reversing camera cannot in any
circumstances be a substitute for
vigilance on the part of the driver.
The superimposed representation of guide
lines helps with the manoeuvre.
They are represented by lines marked "on
the ground" and do not allow the position of
the vehicle to be determined relative to tall
obstacles (for example: other vehicles, ...).
Some deformation of the image is normal.
High pressure jet washing
When washing your vehicle, do not
direct the lance within 30 cm of the
camera lens.
The reversing camera is activated automatically
when reverse gear is engaged.
The image is displayed in the touch screen.
The blue lines represent the general direction
of the vehicle (the difference corresponds to
the width of your vehicle without the mirrors).
The red lines represent a distance of about
30 cm beyond the edge of your vehicle's rear
b u m p e r.
The green lines represent distances of about 1
and 2 metres beyond the edge of your vehicle's
rear bumper. Opening the tailgate causes the display
to disappear.
Clean the reversing camera regularly
using a soft, dry cloth.

Practical information159
208_en_Chap07_informations-pratiques_ed01-2016
Towing a trailer
We recommend the use of genuine
PEUGEOT towbars and their harnesses
that have been tested and approved
from the design stage of your vehicle,
and that the fitting of the towbar is
entrusted to a PEUGEOT dealer or a
qualified workshop.
If the towbar is not fitted by a
PEUGEOT dealer, it must still be
fitted in accordance with the vehicle
manufacturer's instructions.
Your vehicle is primarily designed for
transporting people and luggage, but it may
also be used for towing a trailer.
Driving with a trailer places greater
demands on the towing vehicle and the
driver must take particular care.
For more advice on driving when
towing, refer to the corresponding
section.
For more information on weights (and
the towed loads which apply to your
vehicle) refer to the corresponding
section.
You must observe the maximum trailer
weight, indicated on the registration
certificate or in the technical
specification for your vehicle.
7

Practical information
160
208_en_Chap07_informations-pratiques_ed01-2016
When towing
Distribution of loads
F Distribute the load in the trailer so that the
heaviest items are as close as possible to
the axle and the nose weight approaches the
maximum permitted without exceeding it.
For more information on weights (and the
towed loads which apply to your vehicle) refer
to the corresponding section.
Side wind
F Take into account the increased sensitivity to side wind.
Cooling
Towing a trailer on a slope increases the
temperature of the coolant.
As the fan is electrically controlled, its cooling
capacity is not dependent on the engine speed.
F

I
f the warning lamp and the
STOP warning lamp come on,
stop the vehicle and switch off
the engine as soon as possible.
Braking
Towing a trailer increases the braking distance.
To avoid overheating of the brakes, the use of
engine braking is recommended.
Ty r e s
F Check the tyre pressures of the towing vehicle and of the trailer, observing the
recommended pressures.
Lighting
F Check the electrical lighting and signalling on the trailer and the headlamp beam
height of your vehicle.
For more information on adjusting the
headlamp beam height, refer to the
corresponding section.
The rear parking sensors will be
deactivated automatically if a genuine
PEUGEOT towbar is used.
Air density decreases with altitude, thus reducing
engine per formance. Above 1 000 metres, the
maximum towed load must be reduced by 10
%
for every 1
000 metres of altitude.
F To lower the engine speed, reduce your speed.
The maximum towed load on a long incline
depends on the gradient and the ambient
temperature.
In all cases, keep a check on the coolant
temperature.

Practical information
164
208_en_Chap07_informations-pratiques_ed01-2016
Changing a wiper blade
To maintain the effectiveness of the flat
wiper blades, it is advisable to:
-
h
andle them with care,
-

c
lean them regularly using soapy
water,
-

a
void using them to retain
cardboard on the windscreen,
-

r
eplace them at the first signs of
w e a r.
This position allows the wiper blades to be
moved away from the windscreen.
It is used for cleaning or replacement of the
blades. It can also be useful, in winter, to
release the wiper blades from the windscreen.
Removing a wiper blade
F Lift the corresponding wiper arm away from
the windscreen.
F

U
nclip and remove the wiper blade.
Fitting the new wiper blade
F Position and clip the new wiper blade to the arm.
F

C
arefully lower the wiper arm.
To move the wiper blades to the vertical position:F Any action on the wiper stalk in the minute after switching off the ignition places the
wiper blades vertically on the screen.
To return them to the park position:
F

S
witch on the ignition and operate the
wiper stalk.

Practical information
168
208_en_Chap07_informations-pratiques_ed01-2016
The various caps and covers allow access for
checking the levels of the various fluids and for
replacing certain components.
Petrol
1. Screenwash reservoir.
2. C oolant header tank.
3.
B

rake fluid reservoir.
4.
B

attery / Fuses.
5.


Fusebox.
6.
A

i r f i l t e r.
7.
E

ngine oil dipstick.
8.
E

ngine oil filler cap.
Take care when working under the
bonnet, as certain areas of the engine
may be extremely hot (risk of burns) and
the cooling fan could start at any time
(even with the ignition off).
Checking levels
Check the levels regularly, in line with the
manufacturer's service schedule. Top them up
if necessary, unless otherwise indicated.
If a level drops significantly, have the
corresponding system checked by a PEUGEOT
dealer or a qualified workshop.

Practical information169
208_en_Chap07_informations-pratiques_ed01-2016
The various caps and covers allow access for
checking the levels of the various fluids, for
replacing certain components and for priming
the fuel system.
Diesel
1. Screenwash reservoir.
2. Coolant header tank.
3.
B

rake fluid reservoir.
4.
B

attery / Fuses.
5.


Fusebox.
6.
A

i r f i l t e r.
7.
E

ngine oil dipstick.
8.
E

ngine oil filler cap.
9.
P

riming pump (depending on engine).
The AdBlue
® additive tank filler is located in the
boot below the spare wheel.
Take care when working under the
bonnet, as certain areas of the engine
may be extremely hot (risk of burns) and
the cooling fan could start at any time
(even with the ignition off).
Checking levels
Check the levels regularly, in line with the
manufacturer's service schedule. Top them up
if necessary, unless otherwise indicated.
If a level drops significantly, have the
corresponding system checked by a PEUGEOT
dealer or a qualified workshop.
7

Practical information
170
208_en_Chap07_informations-pratiques_ed01-2016
Level
Brake fluid
The brake fluid level should be close
to the "MA X" mark. If it is not, check
the brake pad wear.
Checking levels
Changing the fluid
Refer to the manufacturer's service schedule
for details of the interval for this operation.
Fluid specification
The brake fluid must conform to the
manufacturer's recommendations. It is normal to top up the oil level
between two services (or oil changes).
PEUGEOT recommends that you check
the level, and top up if necessary, every
3 000 miles (5 000 km).
Oil level
The check is carried out either when the
ignition is switched on using the oil level
indicator in the instrument panel (depending
on version), or using the dipstick.
Engine oil change
Refer to the manufacturer's service schedule
for details of the interval for this operation.
In order to maintain the reliability of the engine
and emission control system, never use
additives in the engine oil.
Oil specification
The oil must be the correct grade for your
engine and conform to the manufacturer's
recommendations.
Check all of these levels regularly, in line with
the manufacturer's service schedule. Top them
up if necessary, unless other wise indicated.
If a level drops significantly, have the
corresponding system checked by a PEUGEOT
dealer or a qualified workshop.
Take care when working under the
bonnet, as certain areas of the engine
may be extremely hot (risk of burns) and
the cooling fan could start at any time
(even with the ignition off). It will only be correct if the vehicle is on level
ground and the engine has been off for more than
30

minutes.