2015 NISSAN JUKE ignition


> (GLW   0RGHO )'@
2-30
Instrument sand controls
SIC2045
How toarm thevehicle security system
GUID-0B0D5 4E3-2D2E-4E66-84C2-DB 089A802C9C
1. Close allwindows.
The system canbearmed evenifthe
windows areopen.
2. Place theignition switchinthe OFF position
and remove theIntelligent Key from the
vehicle.
3. Close alldoors. Lockalldoors. Thedoors
can belocked with:
.
the L OCK
button onthe Intelligent
K ey
.
any request switch
.
the power doorlockswitch
.
the mechanical key
4. Confirm thatthesecurity indicator light
illuminates. Thesecurity indicator lightstays
on for about 30seconds. Thevehicle
security systemisnow pre-armed. After
about 30seconds thevehicle security
system automatically shiftsintothearmed
phase. Thesecurity lightbegins toflash
once every approximately 3seconds. If,
during this30-second pre-armtimeperiod,
the door isunlocked, orthe ignition switchis
placed inthe ACC orON position, the
system willnotarm.
Even when thedriver and/or passengers
are inthe vehicle, thesystem willactivate
with alldoors locked withtheignition
switch inthe LOCK position. Whenplacing
the ignition switchinthe ACC orON
position, thesystem willbereleased.
V ehicle security systemactivation
GUID-586 0D76E-23D 8-4381-99F0 -0DD8252DADA1
The vehicle security systemwillgive thefollow-
ing alarm:
. The headlights blinkandthehorn sounds
intermittently .
. The alarm automatically turnsoffafter
approximately 50seconds. However, the
alarm reactivates ifthe vehicle istampered
with again. The
alarm isactivated by:
. Unlocking thedoor without usingthe
Intelligent Key ,the request switchorthe
key .(Even ifthe door isopened byreleasing
the door inside lockknob, thealarm will
activate.)
How tostop anactivated alarm
GUID-C58 BB668-0D8A- 41CA-8C30-D900891AB B1A
The alarm willstop byunlocking adoor by
pushing theUNL
OCK
button onthe
Intelligent Key ,pushing therequest switchor
using thekey.The alarm willnotstop ifthe
ignition switchisplaced inthe ACC orON
position.
If the system doesnotoperate asde-
scribed above,haveitchecked bya
NISSAN dealer.
NISSAN VEHICLE IMMOBILIZE RSYS-
TEM
GUID-82475E C2-840C-467B-A31D-9 7F570513B2F
The NISSAN Vehicle Immobilizer Systemwillnot
allow theengine tostart without theuse ofthe
registered key.
If the engine failstostart using theregistered
key ,it may bedue tointerference causedby
another registered key,an automated tollroad
device orautomated paymentdeviceonthe key
ring. Restart theengine usingthefollowing
procedures:
&RQGLWLRQ


> (GLW   0RGHO )'@
1. Leave theignition switchinthe ON position
for approximately 5seconds.
2. Place theignition switchinthe OFF or
L OCK position andwait approximately 10
seconds.
3. Repeat step1and 2again.
4. Restart theengine whileholding thedevice
(which mayhave caused theinterference)
separate fromtheregistered key.
If this procedure allowstheengine tostart,
NISSAN recommends placingtheregis-
tered keyonaseparate keyring toavoid
interference fromother devices.
Statement relatedtosection 15ofFCC
rules forNISSAN Vehicle Immobilizer
System (CONTASSY-BCM .ANT ASSY-
IMMOBILISER)
FCC Notice:
For USA:
This device complies withPart15ofthe
FCC Rules. Operation issubject tothe
following twoconditions: (1)This device
may notcause harmful interference, and
(2) this device mustaccept anyinterfer-
ence received, including interference that
may cause undesired operation.
Note: Changes ormodifications notex-
pressly approved bythe party responsible for
compliance couldvoidtheuser's
authority tooperate theequipment.
For Canada:
This device complies withIndustry Canada
licence-exempt RSSstandard(s) .Opera-
tion issubject tothe following twocondi-
tions: (1)this device maynotcause
interference, and(2)this device must
accept anyinterference, includinginterfer-
ence thatmay cause undesired operation
of the device.
SIC2045
Security indicator light
GUID-919 36668-A20A-4 8BD-8CB2-340577FB611D
The security indicator lightislocated onthe
meter panel. Itindicates thestatus ofthe
NISSAN Vehicle Immobilizer System.
The light blinks whenever theignition switchisin
the LOCK, OFForACC position. Thisfunction
indicates thesecurity systems equipped onthe
vehicle areoperational.
If the NISSAN Vehicle Immobilizer Systemis
malfunctioning, thislight willremain onwhile the
ignition switchisin the ON position.
If the light stillremains onand/or the
engine willnotstart, seeaNISSAN dealer
for NISSAN Vehicle Immobilizer System
Instrume ntsand controls
2-31
&RQGLWLRQ


> (GLW   0RGHO )'@
SIC3664
T ype A(if so equipped)
JVI1010X
T ype B(if so equipped)
The windshield wiperandwasher operates
when theignition switchisin the ON position.
Push thelever down tooperate thewiper atthe
following speed:
*
1
Intermittent Ðintermittent operationcanbe
adjusted byturning theknob toward
*
A
(Slower) or
*
B
(Faster) .
*
2
Low Ðcontinuous lowspeed operation
*
3
High Ðcontinuous highspeed operation
Push thelever up
*
4
to have onesweep
operation ofthe wiper.
Pull thelever toward you
*
5
to operate the
washer. Thenthewiper willalso operate several
times.
Pulling upthe wiper arm:
The windshield wipersmustbeinthe service
position inorder toreplace thewiper blades.
T o move thewiper blades tothe service position,
follow thisprocedure:
. When theignition switchisin the ªONº
position orwithin 60seconds ofplacing the
ignition switchtothe ªOFFº position, liftthe
lever up
*
4
two times inless than 0.5
seconds. Thewindshield wiperswillmove to
the service position automatically ,and the
wiper blades cannow bereplaced. To
replace thewiper blades, seeªWindshield
wiper bladesº (P.8-18) . T
o move thewiper blades backtothe original
position:
. Liftthe lever up
*
4
or push thelever down
to operate atany wiper speed.
CAUTION
. This function canbeoperated even
if the ignition switchisin the ªONº
position. However, toprevent an
accident ordamage whenpulling
up the wiper arm,besure toobserve
the following precautions.
Ð Make suretheshift lever isin
the P(Park) position (Continu-
ously Variable Transmission
models) .
Ð Make suretheshift lever isin
the N(Neutral) position,withthe
parking brakefullyapplied
(Manual Transmission models).
Ð Never allowthepassengers to
operate thewindshield wiper
switch inadvertently.
. Donot operate thewindshield wiper
while thewiper armispulled up.The
wiper armmay bedamaged.
Instrume ntsand controls
2-33
&RQGLWLRQ


> (GLW   0RGHO )'@
2-34
Instrument sand controls
GUID-001 3655D-0D8 8-4D9F-87A B-B359910F 5671
WARNING
In freezing temperatures thewasher
solution mayfreeze onthe rear window
glass andobscure yourvision. Warm
the rear window withthedefroster
before youwash therear window.
CAUTION
. Do not operate thewasher continu-
ously formore than30seconds.
. Do not operate thewasher ifthe
reservoir tankisempty.
. Do not fillthe window washer
reservoir tankwithwasher fluid
concentrates atfull strength. Some
methyl alcohol basedwasher fluid
concentrates maypermanently stain
the grille ifspilled whilefilling the
window washerreservoir tank.
. Pre-mix washerfluidconcentrates
with water tothe manufacturer's
recommended levelsbefore pouring
the fluid intothewindow washer
reservoir tank.Donot use the window
washerreservoir tankto
mix thewasher fluidconcentrate
and water.
If the rear window wiperoperation is
interrupted bysnow orice, thewiper may
stop moving toprotect itsmotor. Ifthis
occurs, turnthewiper switch tothe OFF
position andremove thesnow orice that is
on and around thewiper arms.Inapproxi-
mately 1minute, turntheswitch onagain
to operate the wiper.
SIC3666
The rear window wiperandwasher operate
when theignition switchisin the ON position.
T urn theswitch clockwise fromtheOFF position
to operate thewiper.
*
1
Intermittent (INT)Ðintermittent operation(not
adjustable)
*
2
Low (ON) Ðcontinuous lowspeed operation
Push theswitch forward
*
3
to operate the
washer. Thenthewiper willalso operate several
times.
REAR WINDOW WIPERAND
WASHER SWITCH
&RQGLWLRQ


> (GLW   0RGHO )'@
2-36
Instrument sand controls
tion. Itis generally desirable nottoturn
off the headlights forshort intervals
(for example, whenthevehicle stopsat
a traffic signal) .
. Ifthe xenon headlight bulbisclose to
burning out,thebrightness willdrasti-
cally decrease, thelight willstart
blinking, orthe color ofthe light will
become reddish. Ifone ormore ofthe
above signsappear, contactaNISSAN
dealer.
SIC3668
HEADLIGH TSWIT CH
GUID-78 F7386F-88AF- 48CA-8EC4-39D87DBF EDF9
Lighting
GUID-C7E4F4 F1-DC4D-4024-8FF6-AC24A3D2B1F5
*
1
T urn theswitch tothe
position:
The front parking, sidemarker, tail,license plate,
instrument lightswillcome on.However, the
daytime runninglight(forNISMO modelsand
Canada) willturn off.
*
2
T urn theswitch tothe
position:
Headlights willcome onand allthe other lights
remain on.However, thedaytime runninglight
(for NISMO modelsandCanada) willturn
off.
SIC3669
Autolight system(ifso equipped)
GUID-2F 769165-63 29-45F4-95D B-2F94DB2FE66C
The autolight systemallowstheheadlights tobe
set sothey turnonand offautomatically .
T o set the autolight system:
1. Make suretheheadlight switchisin the
AUT Oposition
*
1
.
2. Place theignition switchinthe ON position.
3. The autolight systemautomatically turnsthe
headlights onand off.
T o turn theautolight systemoff,turn theswitch
to the OFF ,
or
position.
The autolight systemcanturn onthe headlights
automatically whenitis dark andturn offthe
&RQGLWLRQ


> (GLW   0RGHO )'@
headlights whenitis light.
For USmodels (ifso equipped): Theheadlights
will also beturned onautomatically attwilight or
in rainy weather (whenthewindshield wiperis
operated continuously) .
If the ignition switchisplaced inthe OFF
position andoneofthe doors isopened andthis
condition iscontinued, theheadlights remainon
for 5
minutes.
SAA1232
Be sure nottoput anything ontop ofthe
photo sensor
*
1
located onthe top ofthe
instrument panel.Thephoto sensor con-
trols theautolight ;if it is covered, the
photo sensor reactsasifitis dark andthe
headlights willilluminate.
Automatic headlights offdelay
GUID-CFAAEF09-71A1-4057 -9F7B-96D46980C786
Y ou can keep theheadlights onfor upto45
seconds afteryouplace theignition switchinthe
OFF position andopen anydoor thenclose all
the
doors.
SIC3670
Headlight beamselect
GUID-65 D36B20-DA E3-4840-AD1 0-0068CB054884
*
1
T o select thelow beam, putthelever inthe
neutral position asshown.
*
2
T o select thehigh beam, pushthelever forward
while theswitch isin the
position. Pullit
back toselect thelow beam.
*
3
Pulling thelever toward youwillflash the
headlight highbeam evenwhen theheadlight
switch isin the OFF position.
Instrume ntsand controls
2-37
&RQGLWLRQ

 
> (GLW   0RGHO )'@
2-38
Instrument sand controls
Battery saversystem
GUID-E840 9034-D45E-48DE-A071- E3A41898289B
. When theheadlight switchisin the
or
position whiletheignition switchisin
the ON position, thelights willautomatically
turn offwithin aperiod oftime after the
ignition switchhasbeen placed inthe OFF
position.
. When theheadlight switchremains inthe
or
position afterthelights auto-
matically turnoff,the lights willturn onwhen
the ignition switchisplaced inthe ON
position.
CAUTION
. When youturn onthe headlight
switch againafterthelights auto-
matically turnoff,thelights willnot
turn offautomatically. Besure to
turn thelight switch tothe OFF
position whenyouleave thevehicle
for extended periodsoftime, other-
wise thebattery willbedischarged.
. Never leavethelight switch on
when theengine isnot running for
extended periodsoftime even ifthe
headlights turnoffautomatically.
Daytime runninglightsystem (forNISMO
models andCanada)
GUID-62FCD 516-90BE-43E6-ACAB-5 CD8364D8567
The daytime runninglightsautomatically illumi-
nate when theengine isstarted withtheparking
brake released. Thedaytime runninglights
operate withtheheadlight switchinthe OFF
position. Turn theheadlight switchtothe
position forfull illumination whendriving atnight.
(The daytime runninglightswillturn off.)
If the parking brakeisapplied beforetheengine
is started, thedaytime runninglightsdonot
illuminate. Thedaytime runninglightsilluminate
once theparking brakeisreleased. Thedaytime
running lightswillremain onuntil theignition
switch isplaced inthe OFF position.
WARNING
When thedaytime runninglightsystem
is active, taillights onyour vehicle are
not on.Itis necessary atdusk toturn on
your headlights. Failuretodo socould
cause anaccident injuringyourself and
others.
SIC4517
SIC4129
&RQGLWLRQ

 
> (GLW   0RGHO )'@
Instrument brightnesscontrol
GUID-95 5DB8AF-41 FD-4C7B-B17D-A344031AD5BB
The instrument brightness controloperates
when theignition switchisin the ON position.
Push thecontrol knob
*
A
to adjust thebright-
ness ofthe instrument panellights. Thebright-
ness indicator
*
B
will beshown brieflyinthe
vehicle information displaywhenthecontrol is
turned.
When thebrightness levelreaches themaximum
or minimum, abeep will
sound.
SIC3671
TURN SIGNAL SWITCH
GUID-DF12F6 F8-A1D7-4024-A4DF-46D972E49E9C
*
1
T urn signal
GUID-3CF 2F736-4960-4B96-B5 CF-1271A559F90A
Move thelever upordown tosignal theturning
direction. Whentheturn iscompleted, theturn
signals cancelautomatically .
*
2
Lane change signal
GUID-BC AE5264-DA08- 4A37-B0F2-FDE7D90FCC 8F
Move thelever upordown untiltheturn signal
begins toflash, butthelever does notlatch, to
signal alane change. Holdthelever untilthelane
change iscompleted.
Move thelever upordown untiltheturn signal
begins toflash, butthelever does notlatch, and
release thelever. Theturn signal willautomati-
cally flash three times. Choose
theappropriate methodtosignal alane
change basedonroad andtraffic conditions.
Instrume ntsand controls
2-39
&RQGLWLRQ