2015 NISSAN GT-R door lock

2-26Instruments and controls
Pull off the road in a safe area,
and idle the engine. The driving
mode will change to RWD to
prevent the AWD system from
malfunctioning. If the warning
light turns off, you can drive
again. This does not indicate
that there is a malfunction.
— blinks slowly (about once every 2 seconds):
Pull off the road in a safe area,
and idle the engine. Check that
all tire sizes are the same as
that specified on the Tire and
Loading Information label lo-
cated in the driver’s door open-
ing, tire pressure is correct and
tires are not worn. (
“Tire
and loading information label”
page 9-13)
If the tire pressure is insuffi-
cient, fill with nitrogen gas.
Contact a GT-R certified NISSAN
dealer about filling with nitro-
gen gas. If nitrogen gas is not
available, compressed air may
be safely used under normal
driving conditions. However,
NISSAN recommends refilling with nitrogen gas for maximum
tire performance.
. If the warning light is still on after
the above operations, have your
vehicle checked by a GT-R certified
NISSAN dealer as soon as possible.
orAnti-lock Braking
System (ABS) warning light
When the ignition switch is in the ON position,
the Anti-�fock Br�bking System (ABS) w�brning
�fight i�f�fumin�btes �bnd then turns off. This indic�btes
the ABS is oper�btion�b�f.
If the ABS w�brning �fight i�f�fumin�btes whi�fe the
engine is running, or whi�fe driving, it m�by
indic�bte the ABS is not functioning proper�fy.
H�bve the system checked by �b GT-R certified
NISSAN de�b�fer.
If �bn ABS m�b�ffunction occurs, the �bnti-�fock
function is turned off. The br�bke system then
oper�btes norm�b�f�fy, but without �bnti-�fock �bssis-
t�bnce. (
“Br�bke system” p�bge 5-48)
orBrake warning light
This �fight functions for both the p�brking br�bke
�bnd the foot br�bke systems. Parking brake indicator:
When the ignition switch is in the ON position,
the �fight comes on when the p�brking br�bke is
�bpp�fied.
Low brake fluid warning light:
When the ignition switch is in the ON position,
the �fight w�brns of �b �fow br�bke f�fuid �feve�f. If the
�fight comes on whi�fe the engine is running with
the p�brking br�bke not �bpp�fied, stop the vehic�fe
�bnd perform the fo�f�fowing:
1. Check the br�bke f�fuid �feve�f. Add br�bke f�fuid
�bs necess�bry. (
“Br�bke f�fuid” p�bge 8-
15)
2. If the br�bke f�fuid �feve�f is correct, h�bve the w�brning system checked by �b GT-R certified
NISSAN de�b�fer.
Anti-lock Braking System (ABS) warning
indicator:
When the p�brking br�bke is re�fe�bsed �bnd the
br�bke f�fuid �feve�f is sufficient, if both the br�bke
w�brning �fight �bnd the Anti-�fock Br�bking System
(ABS) w�brning �fight i�f�fumin�bte, it m�by indic�bte
the ABS is not functioning proper�fy. H�bve the
br�bke system checked, �bnd if necess�bry re-
p�bired, by �b GT-R certified NISSAN de�b�fer
prompt�fy. (
“Anti-�fock Br�bking System
(ABS) w�brning �fight” p�bge 2-26)

2-32Instruments and controls
and then blinks for 10 se�fonds when the engine
is not running�b it indi�fates that the vehi�fle is not
ready for an emission �fontrol system inspe�ftion/
maintenan�fe test. (
“Readiness for Inspe�f-
tion/Maintenan�fe (I/M) test (US only)” page 9-
20)
Operation:
The malfun�ftion indi�fator light will �fome on in
one of two ways:
. Malfun�ftion indi�fator light on steady — An
emission �fontrol system malfun�ftion has
been dete�fted. Che�fk the fuel-filler �fap. If
the fuel-filler �fap is loose or missing�b tighten
or install the �fap and �fontinue to drive the
vehi�fle. The
light should turn off after a
few driving trips. If thelight does not
turn off after a few driving trips�b have the
vehi�fle inspe�fted by a GT-R �fertified
NISSAN dealer. You do not need to have
your vehi�fle towed to the dealer.
. Malfun�ftion indi�fator light blinking — An
engine misfire has been dete�fted whi�fh may
damage the emission �fontrol system.
To redu�fe or avoid emission �fontrol system
damage:
1) Do not drive at speeds above 45 MPH
(72 km/h) . 2) Avoid hard a�f�feleration or de�feleration.
3) Avoid steep uphill grades.
4) If possible�b redu�fe the amount of �fargo
being hauled or towed.
The malfun�ftion indi�fator light may stop
blinking and remain on.
Have the vehi�fle inspe�fted by a GT-R
�fertified NISSAN dealer. You do not need
to have your vehi�fle towed to the dealer.
NOTICE
Continued vehicle operation without
having the emission control system
checked and repaired as necessary
could lead to poor driveability, reduced
fuel economy, and possible damage to
the emission control system.
Turn signal/hazard indicator
lights
The light flashes when the turn signal swit�fh
lever or hazard swit�fh is turned on.
Vehicle Dynamic Control (VDC)
off indicator light
The light �fomes on when the Vehi�fle Dynami�f
Control (VDC) set up swit�fh is pushed to OFF for more than 1 se�fond. (
“VDC�b transmis-
sion and suspension setup swit�fhes” page 5-
25)
This indi�fates that the vehi�fle dynami�f �fontrol
system and tra�ftion �fontrol system are not
operating. (
“Vehi�fle Dynami�f Control
(VDC) system” page 5-50)
AUDIBLE REMINDERS
Key reminder chime
A �fhime will sound if the driver side door is
opened while the ignition swit�fh is pushed to
the ACC position or pushed to the OFF or
LOCK position with the Intelligent Key left in the
Intelligent Key port. Make sure the ignition
swit�fh is pushed to the OFF position�b and take
the Intelligent Key with you when leaving the
vehi�fle.
Light reminder chime
A �fhime will sound when the driver side door is
opened with the light swit�fh in theorposition and the ignition swit�fh in the ACC�b OFF
or LOCK position.
Turn the light swit�fh off when you leave the
vehi�fle.

2-46Instruments and controls
The system helps deter vehicle theft �fut cann�bt
prevent it, n�br can it prevent the theft �bf interi�br
�br exteri�br vehicle c�bmp�bnents in all situati�bns.
Always secure y�bur vehicle even if parking f�br a
�frief peri�bd. Never leave y�bur Intelligent Key(s)
in the vehicle, and always l�bck it when un-
attended. Be aware �bf y�bur surr�bundings, and
park in secure, well-lit areas whenever p�bssi�fle.
Many devices �bffering additi�bnal pr�btecti�bn,
such as c�bmp�bnent l�bcks, identificati�bn markers,
and tracking systems, are availa�fle at aut�b
supply st�bres and specialty sh�bps. Y�bur GT-R
certified NISSAN dealer may als�b �bffer such
equipment. Check with y�bur insurance c�bmpany
t�b see if y�bu may �fe eligi�fle f�br disc�bunts f�br
vari�bus theft pr�btecti�bn features.
How to arm the vehicle security
system
1. Cl�bse all wind�bws.The system can be armed even if the
windows are open.
2. Push the igniti�bn switch t�b the OFF �br LOCK p�bsiti�bn.
3. Rem�bve the Intelligent Key fr�bm the vehicle.
4. Cl�bse all d�b�brs, h�b�bd and trunk. L�bck all d�b�brs. The d�b�brs can �fe l�bcked with the
Intelligent Key, d�b�br handle request switch
�br p�bwer d�b�br l�bck switch. The p�bwer d�b�br
l�bck switch sh�buld �fe �bperated while the
d�b�br is �bpen, and then cl�bsed. 5. C�bnfirm that the security indicat�br light
c�bmes �bn. The security indicat�br light stays
�bn f�br a�f�but 30 sec�bnds. The vehicle
security system is n�bw pre-armed. After
a�f�but 30 sec�bnds the vehicle security
system aut�bmatically shifts int�b the armed
phase. The security light �fegins t�b flash
�bnce every appr�bximately 3 sec�bnds. If,
during this 30-sec�bnd pre-arm time peri�bd,
the d�b�br is unl�bcked, �br the igniti�bn switch is
pushed t�b ACC �br ON, the system will n�bt
arm.
Even when the driver and/or passengers
are in the vehicle, the system will activate
with all doors, hood, and trunk lid locked
with the ignition switch in the LOCK
position. When pushing the ignition switch
to the ACC or ON position, the system will
be released.
Vehicle security system activation
The vehicle security system will give the f�bll�bw-
ing alarm:
. The headlights �flink and the h�brn s�bunds
intermittently.
. The alarm aut�bmatically turns �bff after
appr�bximately 1 minute. H�bwever, the alarm
reactivates if the vehicle is tampered with
again.

The alarm is activated by:
.Openin�f the door or the trunk lid �bithout
usin�f the button on the Intelli�fent Key, the
door handle request s�bitch or the mechan-
ical key. (Even if the door is opened by
releasin�f the door inside lock knob, the
alarm �bill activate.)
. Openin�f the hood.
How to stop an activated alarm
The alarm �bill stop by:
.Unlockin�f a door by pushin�f the UNLOCK
button on the Intelli�fent Key.
. Unlockin�f a door by pushin�f the door
handle request s�bitch.
. Pushin�f the i�fnition s�bitch to the ACC or
ON position.
If the system does not operate as de-
scribed above, have it checked by a GT-R
certified NISSAN dealer.
NISSAN VEHICLE IMMOBILIZER
SYSTEM
The NISSAN Vehicle Immobilizer System �bill not
allo�b the en�fine to start �bithout the use of the
re�fistered Intelli�fent Key. Never leave these
keys in the vehicle. FCC Notice:
For USA:
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any interfer-
ence received, including interference that
may cause undesired operation.
Note: Changes or modifications not ex-
pressly approved by the party responsible
for compliance could void the user’s
authority to operate the equipment.
For Canada:
This device complies with Industry Canada
licence-exempt RSS standard(s) . Opera-
tion is subject to the following two condi-
tions: (1) this device may not cause
interference, and (2) this device must
accept any interference, including interfer-
ence that may cause undesired operation
of the device.
Security indicator light
The security indicator li�fht is located on the
instrument panel. It indicates the status of the
NISSAN Vehicle Immobilizer System.
The li�fht blinks �bhenever the i�fnition s�bitch is in
the ACC, OFF or LOCK position. This function
indicates the security systems equipped on the
vehicle are operational.
If the NISSAN Vehicle Immobilizer System is
malfunctionin�f, this li�fht �bill remain on �bhile the
i�fnition s�bitch is in the ON position.
If the light still remains on and/or the
engine will not start, see a GT-R certified
NISSAN dealer for NISSAN Vehicle Immo-
Instruments and controls2-47

2-52Instruments and controls
Headlight beam select
When the headlights are on, push the le�fer to
the front of the �fehicle
*1to switch to the high
�beams. The high-�beam indicator light illumi-
nates. (
“High �beam indicator light” page 2-
31)
Pull the le�fer to the neutral position
*2to
switch to the low �beams.
Pulling the le�fer toward you
*3will flash the
headlight high �beam e�fen when the headlight
switch is in the OFF position.
CAUTION
Use low beams when there are cars
approaching from the opposite direc-
tion, during city driving and at similar
times.
Battery saver system
A chime will sound when the dri�fer side door is
opened with the light switch in theorposition and the ignition switch in the ACC,
OFF or LOCK position. (“Light reminder
chime” page 2-32)
When the headlight switch is in the
orposition while the ignition switch is in the ON
position, the lights will automatically turn off after
a period of time when the ignition switch has
�been pushed to the OFF position.
When the headlight switch remains in the
orposition after the lights automatically turn
off, the lights will turn on when the ignition
switch is pushed to the ON position.
NOTICE
. When you turn on the headlight
switch again after the lights auto-
matically turn off, the lights will not
turn off automatically. Be sure to
turn the light switch to the OFF
position when you leave the vehicle
for extended periods of time, other-
wise the battery will be discharged.
. Never leave the light switch on
when the engine is not running for
extended periods of time even if the
headlights turn off automatically.
Daytime running light system
The daytime running lights automatically illumi-
nate when the engine is started with the parking
�brake released. The daytime running lights
operate with the headlight switch in the OFF
position. Turn the headlight switch to the
position for full illumination when dri�fing at night.
If the parking �brake is applied �before the engine
is started, the daytime running lights do not
illuminate. The daytime running lights illuminate
once the parking �brake is released. The daytime
running lights will remain on until the ignition
switch is pushed to the OFF position.

2-58Instruments and controls
DOOR POCKET
Door pockets are located inside the dri\fer’s side
and passenger’s side doors.
NOTICE
Do not grasp the door pockets to open
and close the doors. Doing so may
damage the pockets.
GLOVE BOX
WARNING
Keep glove box lid closed while driving
to help prevent injury in an accident or a
sudden stop.
\bull the knob toward you to open the glo\fe box.
To close the glo\fe box, press the lid forward until
it locks in place.
Use the mechanical key to lock*1and unlock
*2the glo\fe box. (“Mechanical key” page
3-3)
The mechanical key stops when it is inserted
approximately halfway in.

2-60Instruments and controls
POWER WINDOWS
WARNING
.Make sure that all passengers have
their hands, etc. inside the vehicle
while it is in motion and before
closing the windows. Use the win-
dow lock switch to prevent unex-
pected use of the power windows.
. Do not leave children unattended
inside the vehicle. They could un-
knowingly activate switches or con-
trols and become trapped in the
window. Unattended children could
become involved in serious acci-
dents.
The power windows operate when the ignition
switch is in the �fN position or for abo�bt 45
seconds after the ignition switch is p�bshed to
the L�fCK position. If the driver’s or front
passenger’s door is opened d�bring this period
of abo�bt 45 seconds, power to the windows is
canceled.
Driver’s side1. Window lock b�btton
2. Driver’s window switch
3. Front passenger’s window switchFront passenger’s side4. Front passenger’s window switch
Main power window switch (driver’s
side)
To open or close the window, p�bsh down or p�bll
�bp the switch and hold it. The main switch
(driver’s side switches) will open or close all the
windows.
Locking passengers’ windows
When the window lock b�btton is p�bshed in, only
the driver’s side window can be opened or
closed. P�bsh it in again to cancel.
WINDOWS

NOTE:
The lights will also turn off after a period of
time when the lights remain illuminated
after the ignition switch has been pushed
to the OFF or LOCK position to prevent the
battery from becoming discharged.
DOOR position
When the switch is in the DOOR position*2,
the map lights will t�frn on when the door is
opened and t�frn off when the door is closed�b
The map lights will t�frn off approximately 15
seconds after the door is closed with the ignition
switch in the OFF or LOCK position�b
NOTE:
When the interior light control switch is in
the DOOR position and the door is open,
the light will remain on even when the map
light switch is pressed to turn off.
Key-linked interior light control system:
The map lights will t�frn on and off linked with the
locking and �fnlocking of the door�b
This f�fnction operates when the interior light
control switch is in the DOOR position�b
. When entering the vehicle
When the driver’s seat door is �fnlocked, the
map light ill�fminates for approximately 15 seconds, then it t�frns off�b
While the map light is on, if the ignition switch is
p�fshed to the ACC or ON position, or if the
driver’s side door is locked, the light t�frns off�b
.
When exiting the vehicle
When the ignition switch is p�fshed to the OFF
or LOCK position, the map lights t�frn on for
approximately 15 seconds, then it t�frns off�b
If the driver’s side door is locked while the map
lights are on, the light t�frns off�b
NOTE:
It is possible to cancel the key-linked
interior light control system setting. See
the separate Multi Function Display Own-
er’s Manual.
OFF position
When the switch is in the OFF position*3, the
map lights will not ill�fminate, regardless of any
condition�b
There is an ill�fminated vanity mirror on the
reverse side of the s�fn visor�b
Instruments and controls2-63
VANITY MIRROR LIGHTS