2015 MITSUBISHI LANCER EVOLUTION maintenance

Replacement of light bulbs
Vehicle care and maintenance 9-29
9
[Except for vehicles with high intensity dis- charge headlights]
[For vehicles with high intensity discharge headlights]
Description
Wattage
ANSI Trade No. or Bulb type
1- Front turn
signal light
21 W WY21W
2- Headlight,
high beam
60 W
9005 HB3
3- Headlight,
low beam/Day- time running light (If so equipped)
51 W
9006 HB4
4- Front fog
light
55 W H11
5- Front side-
marker and parking light
5 W WY5W
6- Side turn sig-
nal light
——
Description
Wattage or Can- dle power
ANSI Trade No. or Bulb type
1- Front turn
signal light
21 W WY21W
2- Daytime run-
ning light
27 W 32 cp
1156
3- Headlight,
low/high beam (Dis- charge bulb)
35 W —
4- Front fog
light
55 W H11
5- Front side-
marker and parking light
5 W WY5W
6- Side turn sig-
nal light
——
WA R N I N G Check with an authorized Mitsubishi Motors dealer or a repair facility of your choice when it is necessary to repair a dis- charge headlight or to replace the bulb. The power circuit, bulb and electrodesgenerate high voltages that may cause a severe electrical shock.NOTE
 The side turn signal light uses LEDs rather than bulbs. For repair and replacement, con- tact an authorized Mitsubishi Motors dealer or a repair facility of your choice.Rear
BK0210800US.bo
ok 29 ページ ２０１４年４月８日　火曜日　午前１１時２８分

Replacement of light bulbs 9-30 Vehicle care and maintenance
9
N00950400558 N00901800105
1. When replacing th
e bulb on the driver’s
side, remove the bo
lt (A) holding down
the relay box and move the relay boxtoward the rear of the vehicle.
2. When replacing the bulb on the passen- ger’s side, lift up the coolant reserve tank (B). 3. Turn the bulb (C) counterclockwise, and then remove the headlight bulb withholder.
Description
Wattage
ANSI Trade No. or Bulb type
7- High-
mounted stop light
——
8- License plate
light
5 W W5W
9- Back-up light 21 W W21W 10- Tail light 5 W W5W11- Tail and stop
light
21/5 W W21/5W
12- Rear turn sig-
nal light
21 W W21W
13- Rear side-
marker light
5 W W5W
NOTE
 The high-mounted stop light uses LEDs rather than bulbs. For repair and replace- ment, contact an authorized Mitsubishi Motors dealer or a repair facility of yourchoice.
Inside
Description
Wattage
1- Trunk area light 5 W2- Dome light (rear) (if so
equipped)
8 W
3- Dome light (front)/Reading
light
8 W
Headlights (low beam, except for vehicles with high intensity discharge headlights)
* - Front of the vehicle * - Front of the vehicle
BK0210800US.bo
ok 30 ページ ２０１４年４月８日　火曜日　午前１１時２８分

Replacement of light bulbs
Vehicle care and maintenance 9-31
9
4. While pressing the tab (D), pull out the bulb (E). 5. To install the bulb, perform the removal steps in reverse.
N00901900076
1. Turn the cap (A) counterclockwise toremove it.
2. Turn the bulb (B) counterclockwise to remove it. 3. While pressing the tab (C), pull out the bulb (D).
* - Front of the vehicle
CAUTIONHandle halogen light bulb with care. The gas inside a halogen light bulb is highly pressur- ized, so dropping, knocking, or scratching a halogen light bulb can cause it to shatter. Never hold the halogen light bulb with a bare hand, dirty glove, etc. The oil from your hand could cause the bulb to break the nexttime the headlights are used. If the glass surface is dirty, clean it with alcohol and let it dry completely beforeinstalling the bulb.
Headlights (high beam, except for vehicles with high intensity discharge headlights)
* - Front of the vehicle * - Front of the vehicle
BK0210800US.bo
ok 31 ページ ２０１４年４月８日　火曜日　午前１１時２８分

Replacement of light bulbs 9-32 Vehicle care and maintenance
9
4. To install the bulb, perform the removal steps in reverse.
N00902000016
Do not attempt to disassemble or repair head- lights, and do not attempt to replace theirbulbs.
N00943200121
The alignment of the headlights should bechecked by an authorized Mitsubishi Motorsdealer or a repair facility of your choice.
N00900300129
1. Turn the cap (A) counterclockwise to remove it. 2. Turn the socket (B) counterclockwise to remove it.
CAUTION Handle halogen light bulb with care. The gas inside a halogen light bulb is highly pressur- ized, so dropping, knocking, or scratching ahalogen light bulb can cause it to shatter. Never hold the halogen light bulb with a bare hand, dirty glove, etc. The oil from your hand could cause the bulb to break the next time the headlights areused. If the glass surface is dirty, clean it with alcohol and let it dry completely beforeinstalling the bulb.
Headlights (low/high beam, for vehicles with high intensity dis- charge lights)
WA R N I N G A high voltage is present in the power cir- cuit and in the bulbs and bulb terminals. To avoid the risk of an electric shock, con-tact an authorized Mitsubishi Motors dealer or a repair facility of your choice whenever repair or replacement is neces-sary.
Adjustment of headlight aim Daytime running lights (for vehicles with high intensity dis- charge headlights) * - Front of the vehicle
BK0210800US.bo
ok 32 ページ ２０１４年４月８日　火曜日　午前１１時２８分

Replacement of light bulbs
Vehicle care and maintenance 9-33
9
3. Turn the bulb counterclockwise while pressing it and pull it out of the socket. 4. To install the bulb, perform the removal steps in reverse.
N00917300482
1. When replacing the bulb on the driver’sside, remove the bolt (A) holding downthe relay box and move the relay box toward the rear of the vehicle. 2. When replacing the bulb on the passen- ger’s side, lift up the coolant reserve tank(B).
3. Turn the socket (C) counterclockwise to remove it. 4. Pull the bulb out of the socket.
* - Front of the vehicle
Front side-marker and parking lights (except for vehicles with high intensity discharge head- lights) * - Front of the vehicle
*- Front of the vehicle * - Front of the vehicle
BK0210800US.bo
ok 33 ページ ２０１４年４月８日　火曜日　午前１１時２８分

Replacement of light bulbs 9-34 Vehicle care and maintenance
9
5. To install the bulb, perform the removal steps in reverse.
N00917300466
1. To create enough work space, turn thesteering wheel all the way in the direction opposite to the side you wish to replace. 2. Remove the clips (A), clip (B) and screw(C) to turn up the cover (D).
3. Turn the socket (E) counterclockwise to remove it. 4. Pull the bulb out of the socket.
5. To install the bulb, perform the removal steps in reverse.
N00943400338
1. Remove the clips (A) and clips (B), thenremove the duct (C) and the upper cover(D).
Front side-marker and parking lights (for vehicles with high intensity discharge headlights)
Front turn signal lights
BK0210800US.bo
ok 34 ページ ２０１４年４月８日　火曜日　午前１１時２８分

Replacement of light bulbs
Vehicle care and maintenance 9-35
9
2. Remove the entire socket and bulb assem- bly (E) by turning it counterclockwise. 3. Remove the bulb by pulling it out.
4. To install the bulb, perform the removal steps in reverse.
N00943600646
1. Remove the clips (A) and clips (B), thenturn up the cover (C).
2. While pressing the tab (D), pull out the socket (E). 3. Turn the bulb (F) counterclockwise to remove it. 4. To install the bulb, perform the removal steps in reverse.
* - Front of the vehicle
Front fog lights
BK0210800US.bo
ok 35 ページ ２０１４年４月８日　火曜日　午前１１時２８分

Replacement of light bulbs 9-36 Vehicle care and maintenance
9
N00943700399
1. Remove the screws (A) from the light unit. 2. Remove the light unit in the rear direc- tion.
3. Remove the socket and bulb assemblies by turning them counterclockwise. 4. Remove the bulb by pulling it out.
CAUTION Handle halogen light bulbs with care. The gas inside a halogen light bulb is highly pres- surized, so dropping, knocking, or scratching a halogen light bulb can cause it to shatter. Never hold the halogen lights bulb with a bare hand, dirty glove, etc. The oil from your hand could cause the bulb to break the nexttime the fog lights are used. If the glass surface is dirty, clean it with alcohol and let it dry completely beforeinstalling the bulb.
Rear combination lights Tail and stop lights, rear turn sig- nal lights and rear side-marker lights
B- Tail and stop light C- Rear turn signal light D- Rear side-marker light
BK0210800US.bo
ok 36 ページ ２０１４年４月８日　火曜日　午前１１時２８分