
Free-hand Advanced Security Transmitter (F.A.S.T.-key) (if so equipped) 5-26 Features and controls
5
After several attempts, you may experience that the engine still does not start. 1. Make sure that all electric devices, such as lights, air conditioning blower and rear window defogger, are turned off.
2. While depressing the brake pedal on vehi- cles equipped with Twin Clutch SST or the clutch pedal on the vehicles equipped with manual transaxle, press the accelera-tor pedal halfway and hold it there, then crank the engine. Release the accelerator pedal, immediately after the engine starts.3. If the engine still will not start, the engine could be flooded with too much gasoline. While depressing the brake pedal on vehi-cles equipped with Twin Clutch SST orthe clutch pedal on the vehicles equipped with manual transaxle, push the accelera- tor pedal all the way down and hold itthere, then crank the engine for 5 to 6 sec- onds. Return the ignition switch to the “LOCK” position and release the acceler-ator pedal. Wait a few seconds, and then crank the engine again for 5 to 6 seconds while depressing the brake pedal or theclutch pedal, but do not push the accelera- tor pedal. Release the ignition key if the engine starts. If the engine fails to start,repeat these procedures. If the engine still will not start, contact your local Mitsubishi Motors dealer or a repair facil-ity of your choice for assistance.
When the ambient temperature is -22 °F (-30 °C) or lower, it may not be possible tostart from a standstill even with the gearshift lever in the “D” (DRIVE) or “R” (REVERSE) position.This phenomenon occurs because the trans- mission has not warmed up sufficiently; it does not indicate a problem. If it occurs,place the gearshift lever in the “P” (PARK)position and let the engine idle for at least 10 minutes. The transmission will warm up, and you willbe able to start normally. Do not leave the vehicle during warm-up operation.
N00529600055
The electronic immobilizer is designed to sig-nificantly reduce the possibility of vehicle theft. The purpose of the system is to immo- bilize the vehicle if an invalid start isattempted. A valid start attempt can only be achieved (subject to certain conditions) using a F.A.S.T.-Key “registered” to the immobi-lizer system.
WA R N I N G Make sure to remove the F.A.S.T.-key from the emergency key after the engine is started. If not removed, the F.A.S.T.-key could fall to the floor, which could disturb the pedaloperation. Furthermore, the F.A.S.T.-key could prevent the driver’s knee airbag from inflating normally or could be pro-pelled to cause serious injury if the airbag inflates.NOTE
If the emergency key is attached to a key ring, it may become impossible to insert the F.A.S.T.-key into the emergency key, and it may prevent the engine from being started.When using the emergency key to start the engine, first remove the key from the key ring.
When the engine is hard to start
Startability of Twin Clutch SST vehicle with an ambient temperature of -22 °F (-30 °C) or lowerElectronic immobilizer (Anti- theft starting system)
BK0210800US.bo
ok 26 ページ 2014年4月8日 火曜日 午前11時28分

Theft-alarm system 5-40 Features and controls
5
At this time, the theft-alarm indicator (A) on the audio panel flashes for confirma- tion. 4. The system has entered the armed stage after about 20 seconds, when the theft-alarm indicator (A) flashing becomes slower. The theft-alarm indicator (A) continues toflash while the system is in the armed stage.
The alarm will be activated if any of the fol- lowing occur while the vehicle is parked andthe system is armed.
One of the doors is opened without using the keyless entry system or the F.A.S.T.- key operation. The engine hood or the trunk lid is opened.
When the alarm is activated: 1. The headlights blink on and off for 3 min- utes.After 3 minutes the headlights automati- cally shut off. 2. The horn will sound intermittently for 3minutes.
Arm the system and leave
NOTE
If the engine hood or the trunk lid is open, the theft-alarm indicator (A) illuminates and the system cannot enter the armed stage. The system enters the armed stage about 20 sec- onds after the engine hood or the trunk lid isclosed. The system will be disarmed if, while the theft-alarm indicator (A) is illuminated, all doors are unlocked by the keyless entry sys- tem, the F.A.S.T.-key operation. The system will be disarmed if, while the theft-alarm indicator is illuminated, the igni-tion switch is turned to the “ON” position. The system will not be
armed if a door or the
trunk lid or the engine hood is not com- pletely closed. If this happens, rearm the sys- tem as described above. The theft-alarm system can be activated when people are riding inside the vehicle orwhen the windows are open. To prevent acci- dental activation of the alarm, do not set the system to the system armed mode while peo-ple are riding in the vehicle.
Alarm stage
Type of alarm Horn sounds!Headlights blink on and off!
BK0210800US.bo
ok 40 ページ 2014年4月8日 火曜日 午前11時28分

Theft-alarm system
Features and controls 5-41
5
The alarm can be deactivated in the following ways. By using the keyless entry system or the F.A.S.T.-key operation to lock or unlock the door. Turn the ignition switch to the “ON” posi- tion.
The system will be disarmed if the following operation is performed. The ignition switch is turned to the “ON” position. All doors are unlocked by the keyless entry system or the F.A.S.T.-key opera-tion.
Use the following procedure to test the sys- tem: 1. Lower the driver’s window. 2. Arm the system as explained in “Armedstage”. 3. Make sure that the theft-alarm indicator comes on and flashes for approximately20 seconds. 4. Wait a few seconds and then unlock the driver’s side door by using the inside doorlock knob and open the door. 5. Check to be sure that the horn sounds intermittently and the headlights blink onand off when the door is opened. 6. Disarm the system by unlocking all doors by the keyless entry system or theF.A.S.T.-key operation.
NOTE
The alarm will continue to operate for 3 min- utes. At the end of that period, the alarm will automatically shut off to save battery power. The system will then
be rearmed until the
proper disarming step is taken. The alarm will resume if unauthorized actions are taken again, even if the alarm hasstopped. While the alarm is operating, a warning is displayed on the information screen in the multi-information display.
Alarm deactivation
Disarmed stage
NOTE
If the UNLOCK button is pressed when all doors are closed and no door is opened within approximately 30 seconds, re-arming will automatically occur. The amount of time after unlocking until the vehicle relocks automatically can beadjusted. See an authorized Mitsubishi Motors dealer for details.Disarm...by the keyless entry system or F.A.S.T.-key operation
Once the system has been disarmed, it can- not be rearmed except by repeating the arm- ing procedure.
Testing the theft-alarm system
NOTE
BK0210800US.bo
ok 41 ページ 2014年4月8日 火曜日 午前11時28分

Power windows 5-42 Features and controls
5
N00510800266
N00548700114
The main switch located on the driver’s door can be used to operate all door windows. A window can be opened or closed by operat-ing the corresponding switch.Press the switch down to open the window, and pull up the switch to close it. If the driver’s door window switch is fullypressed down/pulled up, the driver’s door window automatically opens/closes com- pletely.If you want to stop the window movement, operate the switch lightly in the reverse direc- tion.
Power windows 1- Open (down) 2- Close (up)
NOTE
Never try to operate the main switch and sub switch in different directions at the sametime. This will freeze the window in posi- tion. Operating the power windows repeatedly with the engine stopped will run down the battery. Use the window switches only whilethe engine is running. WA R N I N G Before operating the power windows, make sure that nothing can be trapped(head, hands, fingers, etc.) in the window.
Never leave the vehicle with the key in the ignition switch. Never leave a child alone in the vehicle.
Main switch
WA R N I N G
1- Driver’s door window switch 2- Front passenger door window switch 3- Left rear door window switch 4- Right rear door window switch 5- Window lock switch
BK0210800US.bo
ok 42 ページ 2014年4月8日 火曜日 午前11時28分

Power windows
Features and controls 5-43
5
N00548800085
Each sub switch can be used for its own pas-
senger door window, unless the driver’s win-
dow lock switch is activated.
N00548900116
The power windows can be run up or down
when the ignition switch is in the “ON” posi-
tion.
The door windows can be opened or closed
for a 30 second period after the ignition
switch is turned to the “ACC” or “LOCK”
position. However, once the driver’s door or
the front passenger’s door is opened, the
power windows cannot be operated.
N00528800076
If a hand or head is trapped, for safety the
door window is automatically lowered a little.
After the door window is lowered, pull up the
switch again to close the door window.
N00549000068
When this switch is in the lock mode, the
main switch for passenger door window and
the sub switch cannot be used to open or
close the door window, and the main switch
will open or close only the driver’s door win-
dow. To unlock the switch, press it again.
Sub switch 1- Close (up)
2- Open (down)Timer function
Safety mechanism (Driver’s
door window only)
WA R N I N G If the safety mechanism is activated three
or more times successively, the safety
mechanism will be temporarily cancelled.
If a hand or head subsequently gets
trapped, a serious injury can result.The safety mechanism is deactivated while
the switch is pulled up continuously.
Therefore be especially careful that hands
or head are not trapped in the door win-
dow opening.Do not deliberately trap your hands or
head in order to activate the safety mecha-
nism.
Your hands or head could be trapped and
personal injury could result.CAUTIONThe safety mechanism is deactivated just
before the door window closes. This allows
the door window to close completely. There-
fore be especially careful that fingers are not
trapped in the door window opening.
NOTE
The safety mechanism may be activated if
the driving conditions or other circumstances
cause the door window to be subjected to a
physical shock similar to that caused by
trapped hand or head.
If the safety mechanism is activated 3 or
more times consecutively, the safety mecha-
nism is deactivated and normal closing of the
door window will be aborted.
Use the following method to return to normal
operation.
1. If the door window is open, repeatedly pull up the power window switch to fully
close the door window.
2. With fully closing the window, release the switch and then pull up the switch
again for about 1 second.Lock switch
SC00000600-3.fm 43 ページ 2014年4月16日 水曜日 午後2時6分

Sunroof (if so equipped)
5-44 Features and controls
5
N00551400014
Wind buffeting can be described as the per-
ception of pressure on the ears or a booming
or rumbling sound. Your vehicle may exhibit
wind buffeting when driving with one or both
rear door windows down or partially opened.
This is a normal occurrence that can be mini-
mized. If the buffeting occurs with the reardoor windows open, open the front door win-
dows as well as the rear door windows to
minimize the condition.
N00511000496
The sunroof can be opened and closed with
the ignition switch in the “ON” position.
Press the switch (1), the sunroof automati-
cally opens and the sunroof will stop several
centimeters this side of
the full open position.
Press the switch (1) again, and the sunroof
will be fully open.
To stop the moving sunroo f, press the switch.
1- Lock
2- Unlock
WA R N I N G Before driving with a child in the vehicle,
be sure to lock the window switch to make
it inoperative. Children tampering with
the switch could easily trap their hands or
heads in the window. What to do if you hear wind
buffeting when driving
Sunroof
(if so equipped)
WA R N I N GDo not stick your head, hands or anything
else in the sunroof opening. Before operating the sunroof, make sure
that nothing can be trapped (head, hands,
fingers, etc.).Never leave a child (or other person who is
incapable of safely operating the sunroof
switch) alone in the vehicle.
To open
NOTE
The sunroof stops just before reaching the
fully open position. If the vehicle is driven
with the sunroof in this position, wind buf-
feting is lower than with the sunroof fully
open.
SC00000600-3.fm 44 ページ 2014年4月16日 水曜日 午後2時6分

Inside day/night rearview mirror 5-48 Features and controls
5
N00548600070
Adjust the inside rear
view mirror only after
making any seat adjustme
nts so as to have a
clear view to the rear of the vehicle. Adjust the inside mirror to maximize the view through the rear window.
It is possible to move
the mirror up and down
to adjust its position. It is possible to move the mirror up/down and left/right to adjust its position.
The day/night knob (A) at the bottom of the mirror can be used to adjust the mirror toreduce the glare from the headlights of vehi-cles behind you during night driving.
Inside day/night rearview mirror
WA R N I N G Do not attempt to adjust the inside rear- view mirror while driving. This can be dangerous.Be sure to adjust the mirror before driv- ing.Type 1 Ty p e 2
To adjust the vertical mirror position To adjust the mirror position
To reduce the glare Ty p e 1
BK0210800US.bo
ok 48 ページ 2014年4月8日 火曜日 午前11時28分

Ignition switch 5-50 Features and controls
5
The outside mirror can be folded in toward the side window to prevent damage whenparking in tight locations.
N00549301257
When the rear window defogger switch ispressed with the engine running, the outsiderearview mirrors are defogged or defrosted. Current will flow through the heater element inside the mirrors, thus clearing away frost orcondensation.
The indicator light (A) will illuminate while the defogger is on. The heater will be turned off automatically in about 20 minutes.
N00512400572
[For vehicles equipped with the F.A.S.T.- key] For information on operations for vehiclesequipped with the F.A.S.T.-key, refer to “F.A.S.T.-key: Ignition switch” on page 5-15. [Except for vehicles equipped with the F. A . S . T. - k e y ]
The engine is off and the steering wheel is locked. The key can be inserted and removedonly when the switch is in this position. Allows operation of electrical accessories with the engine off. The engine runs and all accessories can be used.
NOTE
After adjusting, return the lever to the “•”(off) position (C).
To fold the mirror Heated mirror
Ignition switch
LOCK ACC ON Manual transaxle
Twin Clutch SST
BK0210800US.bo
ok 50 ページ 2014年4月8日 火曜日 午前11時28分