2015 MITSUBISHI L200 MPG

Average fuel consumption
E00518200267
The average fuel consumption during the pe-
riod since the last reset is shown in (A) and
the momentary fuel consumption in (C). The average value of the fuel consumption is
graphed every 5 minutes and the data for up
to 4 hours are shown in (B). When you press
the “MANUAL” function button in the auto reset mode, the mode will be changed to the manual reset mode. When you press the
“AUTO” function button in the manual reset
mode, the mode will be changed to the auto reset mode.
Auto reset modeManual reset mode
NOTEl When you turn the ignition switch to the
“ON” position after turning it from the “ON” position to the “ACC” or “LOCK” po-
sition in the manual reset mode, the auto re- set mode will automatically be selected.
l When the average fuel consumption cannot
be calculated, “--.-” will be shown.
l The average and momentary fuel consump-
tion change depending on the driving condi- tion (road condition, driving behavior, etc.). The indications may differ from the actual
fuel consumption. Therefore, it is recom- mended to use the indications as reference.
l The unit indication can be changed to your
desired setting {km/L, L/100 km, mpg (UK
GALLON), or mpg (US GALLON)}. Refer to “User customization” on page 5-27.
Resetting the average fuel consumption
Press the “RESET” function button to reset
the average fuel consumption indication.
NOTEl The average fuel consumption can be reset
separately for the auto reset mode and forthe manual reset mode.
l When you turn the ignition switch to the
“ON” position about 4 hours (or more) after turning it from the “ON” position to the
“ACC” or “LOCK” position in the auto reset
mode, the average fuel consumption indica-
tion will automatically be reset.Driving range
E00518300095
This value (A) shows the distance (in km or
miles) that can be driven on the fuel remain- ing in the fuel tank. The driving range is
graphed every 5 minutes and the data for up
to 4 hours are shown in (B).
Centre information display*
5-14OKTE15E3Instruments and controls5

User customization
E00519600183
You can set the indication of unit, language,
and the time notation.
In addition, you can return these settings to
the factory default settings.
Selecting the item to set
1. Press the “ADJ” button to select the user
customization display.
2. Press the function button “←” or “→” to
select the item you wish to set.
l “UNIT”: Changing the unit
l “LANGUAGE”: Changing the lan-
guage
l “12h ↔ 24h”: Changing the time for-
mat
l “DEFAULT”: Resetting to factory
settings
Push the function button “SELECT”.
The setting display for your selected
item will appear.
Changing display units
It is possible to change the display units for the fuel consumption, driving range, average
speed, outside temperature, elevation, and at- mospheric pressure as shown below.
FUEL ECONO-
MYkm/L → L/100 km →
mpg (UK GALLON) → mpg (US GALLON)RANGEkm → milesSPEEDkm/h → mphOUTSIDE TEM-
PERATURE°C → °FELEVATIONm → ftBAROMETERhPa → mb → kPa →
inHg

l Changing the display unit for fuel con-
sumption
1. Press the “←” or “→” function button to
select “FUEL ECONOMY”. Then press the “SELECT” function button.
2. Press the “←” or “→” function button to
select “km/L”. Then press the “SET”
function button. The display will flash
twice, and the display unit will be upda- ted to the selected one.
Centre information display*
5-27OKTE15E3Instruments and controls5

NOTElThe 2WD/4WD operation indication lamp
blinks while the selection is in process. Takethe following precautions when the indica-tion lamp is blinking or remains off.
• Keep the steering wheel in the straight
ahead position while making range selec-
tions. If you attempt to drive forward with the steering wheel turned, gear rattling
may occur and the desired range may not actually be selected.
• If you move the transfer shift lever from
“4H” to “4HLc” while the vehicle is sta-
tionary, keep your speed initially very low
when you subsequently make a standing start. Before driving at normal speeds,
confirm that the centre differential lock lamp has changed from blinking to steadyillumination.
• If you move the transfer shift lever from
“4HLc” to “4H” and the centre differen-
tial lock lamp does not stop blinking, place the steering wheel in the straight ahead position and slowly depress the ac-
celerator pedal several times.NOTE• If you move the transfer shift lever from
“4H” to “2H” and the front wheel lamp
does not stop blinking, confirm safety around the vehicle then accelerate, decel-
erate, and reverse until the front wheel lamp goes off. When the front wheel lampgoes off, you can then proceed to drive the vehicle.
If you accelerate, decelerate, and reverse but the front wheel lamp still does not
stop blinking, return the transfer shift lev- er to “4H” then have your vehicle inspec-
ted.
l When you move the transfer shift lever from
“4H” to “4HLc”, there may be a slight delay before the centre differential lock lamp illu-
minates.Rear differential lock*
E00606200115
If one wheel starts to spin freely and the vehi-
cle becomes stuck and cannot be freed even using 4-wheel drive, the rear differential lock switch (A) can be used to activate the reardifferential lock for extra traction.
Operating the rear differential
lock
1. Move the transfer shift lever to “4L” or
“4H” position (easy select 4WD), “4LLc” or “4HLc” position (super select4WD).
2. To activate the rear differential lock,
press the rear differential lock switch
(1).
Rear differential lock*
6-34OKTE15E3Starting and driving6