2015 MITSUBISHI L200 maintenance

Replacement of lamp bulbsE01003100710
Before replacing a bulb, ensure the lamp is off. Do not touch the glass part of the new
bulb with your bare fingers; the skin oil left
on the glass will evaporate when the bulb gets hot and the vapour will condense on the
reflector and dim the surface.CAUTIONl Bulbs are extremely hot immediately after
being turned off.
When replacing a bulb, wait for it to cool sufficiently before touching it. You couldotherwise be burnt.NOTEl If you are unsure of how to carry out the
work as required, we recommend you to consult a specialist.
l Be careful not to scratch the vehicle body
when removing a lamp or lens.
l When it rains or when the vehicle has been
washed, the inside of the lens sometimes be-
comes foggy. This is the same phenomenon as when window glass mists up on a humid
day, and does not indicate a functional prob- lem. When the lamp is switched on, the heat
will remove the fog. However, if water gath-
ers inside the lamp, we recommend you to have the lamp checked.Bulb capacity
E01003200085
When replacing a bulb, use a new bulb with
the same wattage and colour.
Outside
E01003304169
Front
1- Headlamps, high-beam: 60 W (HB3)2- Headlamps, low beam: 55 W (H11)
3- Front turn-signal lamps: 21 W (PY21W)
4- Position lamps: 5 W (W5W)
5- Front fog lamps*: 55 W (H11)
6- Side turn-signal lamps (on fender)*: 5 W
(WY5W)
7- Side turn-signal lamps (on outside rear-
view mirror)*Type 2
1- Headlamps, high/low beam: 60/55 W
(H4)
2- Position lamps: 5 W (W5W)
3- Front turn-signal lamps: 21 W (PY21W) 4- Front fog lamps*: 55 W (H11)
5- Side turn-signal lamps (on fender)*: 5 W
(WY5W)
6- Side turn-signal lamps (on outside rear-
view mirror)*

Codes in parentheses indicate bulb types.
Replacement of lamp bulbs
10-25OKTE15E3Maintenance10 Type 1

NOTElThe side turn-signal lamp (on outside rear-
view mirror) uses an LED instead of a bulb. For repair and replacement, contact a
MITSUBISHI MOTORS Authorized Serv-
ice Point.
Rear
Type 1Type 2
1- High-mounted stop lamp: 5 W (W5W)
2- Rear turn-signal lamps: 16 W (W16W)3- Tail and stop lamps: 21/5 W (P21/5W)
4- Reversing lamps: 16 W (W16W)
5- Rear fog lamp (Type 1, Driver’s side on-
ly): 21 W (P21W)
6- Rear fog lamp (Type 2, Driver’s side on-
ly): 21 W (W21W)
7- Licence plate lamps: 5 W (W5W)

Codes in parentheses indicate bulb types.Inside
E01003401518
Single cab
1- Door courtesy lamps*: 3.4 W
2- Room lamp: 8 W
3- Glove box lamp: 1.4 W
4- Centre console downlight: 1.4 W
Club cab
1- Door courtesy lamps*: 3.4 W
2- Front room lamp and personal lamps*: 7.5 W
3- Rear room lamp: 8 W
4- Glove box lamp: 1.4 W
5- Centre console downlight: 1.4 W
Replacement of lamp bulbs
10-26OKTE15E3Maintenance10

Double cab
1- Door courtesy lamps*: 3.4 W
2- Front room lamp and personal lamps: 7.5 W
3- Rear room lamp*: 8 W
4- Glove box lamp: 1.4 W
5- Centre console downlight: 1.4 W
Headlamps
E01003501375
Type 1
1. Remove the bulb and connector assem-
bly (A) by turning it anticlockwise.
High beamLow beam2. Depress the tab (B) on the harness con-
nector and pull the harness connector
(C) to remove it.High beamLow beam
3. To install the bulb, perform the removal
steps in reverse.
CAUTIONl Handle halogen lamp bulbs with care. The
gas inside halogen lamp bulbs is highly pres- surized, so dropping, knocking, or scratching
a halogen lamp bulb can cause it to shatter.
l Never hold the halogen lamp bulb with a
bare hand, dirty glove, etc.
The oil from your hand could cause the bulb to break the next time the headlamps are op-
erated.
If the glass surface is dirty, it must be cleaned with alcohol, paint thinner, etc., and
refit it after drying it thoroughly.
Replacement of lamp bulbs
10-27OKTE15E3Maintenance10

Type 2
1. Disconnect the connector (A).
2. Remove the sealing cover (B).
3.Unhook the spring (C) which secures the
bulb, and then remove the headlamp bulb.
4. To install the bulb, perform the removal
steps in reverse.
CAUTIONl Handle halogen lamp bulbs with care. The
gas inside halogen lamp bulbs is highly pres-
surized, so dropping, knocking, or scratching
a halogen lamp bulb can cause it to shatter.
l Never hold the halogen lamp bulb with a
bare hand, dirty glove, etc.
The oil from your hand could cause the bulb to break the next time the headlamps are op-
erated.
If the glass surface is dirty, it must be cleaned with alcohol, paint thinner, etc., andrefit it after drying it thoroughly.
Replacement of lamp bulbs
10-28OKTE15E3Maintenance10

Position lamps
E01003700833
Type 1
1. Turn the bulb socket anticlockwise to re-
move it. And remove the bulb from the
socket by pulling out.
2. To install the bulb, perform the removal
steps in reverse.
Type 2
1. Turn the bulb socket anticlockwise to re-
move it. And remove the bulb from the
socket by pulling out.
2. To install the bulb, perform the removal
steps in reverse.
Front turn-signal lamps
E01003800818
Type 1
1. Turn the bulb socket anticlockwise to re-
move it. And remove the bulb from the
socket by turning it anticlockwise while
pressing in.
2. To install the bulb, perform the removal
steps in reverse.
Type 2
1. Turn the bulb socket anticlockwise to re-
move it. And remove the bulb from the
socket by turning it anticlockwise while pressing in.
Replacement of lamp bulbs
10-29OKTE15E3Maintenance10

2.To install the bulb, perform the removal
steps in reverse.Side turn-signal lamps (on
fender)*
E01003901702
1. To remove a side turn-signal lamp, insert a straight blade (or minus) screwdriverat the end of the lamp nearer the front of
the body and use it to gently lever the lamp out of the body.
Front
NOTEl Wrap a piece of cloth around the tip of the
screwdriver in order to avoid scratching the
lens and the body.2. Remove the socket and bulb assembly
together by turning it anticlockwise, and then remove the bulb by pulling it out.
3. To install the bulb, perform the removal
steps in reverse.
NOTEl When replacing the lamp assembly, push in
the end facing the rear of the vehicle first.NOTESide turn-signal lamps (on out-
side rear-view mirrors)*
E01003900646
The side turn-signal lamp (on outside rear-
view mirror) uses an LED instead of a bulb. For repair and replacement, contact a MITSUBISHI MOTORS Authorized Service
Point.
Front fog lamps*
E01004002882
Type 1
1. Insert a straight blade (or minus) screw-
driver with a cloth over its tip at the edge
Replacement of lamp bulbs
10-30OKTE15E3Maintenance10 Front

of the cover and pry gently to remove
the cover.
2. Turn the 3 bolts (A) anticlockwise to re-
move them. And then remove the lamp assembly.
3. Depress the tab (B) on the harness con-
nector and pull the harness connector
(C) to remove it.
4. Turn the entire socket and bulb assembly
(D) anticlockwise to remove it.
5. To install the bulb, perform the removal
steps in reverse.
CAUTIONl Handle halogen lamp bulbs with care. The
gas inside halogen lamp bulbs is highly pres-
surized, so dropping, knocking, or scratching
a halogen lamp bulb can cause it to shatter.
l Never hold the halogen lamp bulb with a
bare hand, dirty glove, etc.
The oil from your hand could cause the bulb to break the next time the fog lamps are op- erated.
If the glass surface is dirty, it must be
cleaned with alcohol, paint thinner, etc., and refit it after drying thoroughly.
Replacement of lamp bulbs
10-31OKTE15E3Maintenance10

Type 2
1.Push up the tab (A) of the clip to unfix
it, and then pull the cover towards you to
remove it.
2. Remove the 3 screws (B) and remove
the lamp unit.
NOTEl When unfastening the screws, be careful not
to move the beam position adjustment screw
(C).
3. Depress the tab (D) on the harness con-
nector and pull the harness connector (E)
to remove it.
4. Turn the bulb (F) anticlockwise to re-
move it.
5. To install the bulb, perform the removal
steps in reverse.
CAUTIONl Handle halogen lamp bulbs with care. The
gas inside halogen lamp bulbs is highly pres- surized, so dropping, knocking, or scratching
a halogen lamp bulb can cause it to shatter.
l Never hold the halogen lamp bulb with a
bare hand, dirty glove, etc.
The oil from your hand could cause the bulb to break the next time the fog lamps are op-
erated.
If the glass surface is dirty, it must be cleaned with alcohol, paint thinner, etc., andrefit it after drying thoroughly.
Replacement of lamp bulbs
10-32OKTE15E3Maintenance10