2015 MITSUBISHI iMiEV clock

Antenna 7-22 Comfort controls
7
 Be sure to observe the handling instruc- tions for the CD-R/RW disc.
N00734200471
Turn the pole (A) counterclockwise. Screw the pole (A) clockwise into the base (B) until it is securely retained.
N00755001134
The time is displayed when the electric motorswitch is in the “ON” or “ACC” position.
1. Press and hold the clock button and the clock display flashes. 2. Press the SEEK button to adjust the“hours” digit. If you keep pressing the button, fast-for- ward begins.3. When the “hours” digit is adjusted, press the clock button to flash the “minutes” digit.Press the SEEK button to adjust the “min- utes” digit. If you keep pressing the button, fast-for-ward begins.
WA R N I N G Operating the CD player in a manner other than specifically instructed herein may result in hazardous radiation expo- sure. Do not remove the cover and attemptto repair the CD playe
r by yourself. There
are no user serviceable parts inside. In case of malfunction, contact a certified i-MiEV dealer.
Antenna To remove To install
NOTE
 Be sure to remove the roof antenna in the following cases: • When using an automatic car wash • When covering your ve
hicle with a car
cover • When driving into a structure that has a low ceiling.
Clock
To set the time A- Clock button B- SEEK (clock adjustment up) buttonC- SEEK (clock adjustment down) but-
ton
BK0209800US.book 22 ページ ２０１４年１月１４日　火曜日　午前９時２６分

General information about your radio
Comfort controls 7-23
7
4. When the time is set, press the clock but- ton to stop the clock display from flash-ing.
N00733900439
Your vehicle’s radio receives both AM andFM stations. The quality of your reception is affected by distance, obstacles, a
nd signal interference.
This radio complies with
Part 15 of Federal
Communications Commission (FCC) Rules (for vehicles sold in U.S.A.). Operation is subject to the following conditions:  The device may not cause harmful inter- ference.  This device must ac
cept any interference
recieved, including interference that maycause undesirable operation.
FM signals do not follow the earth surface nor are they reflected by the upper atmo-sphere. For this reason
, FM broadcasts cannot
be received over long
distances. AM signals
follow the earth’s surface and are reflected bythe upper atmosphere. For this reason, AM broadcasts can be rece
ived over longer dis-
tances.
Because of the limited
range of FM signals
and the way FM waves transmit, you may experience weak or
fading FM reception.
When the broadcast is blocked by mountains or similar obstructions,
reception can be dis-
turbed. The reason why one can hear FM but not AM in parking garages, under
bridges etc., is that
FM signals, unlike AM
signals, are reflected
by solid objects such
as buildings, etc.
Because FM signals ar
e easily reflected by
buildings, this can also cause reception dis- turbances.The direct signal from
the broadcast station
reaches the antenna sl
ightly before the
reflected signal. This
time difference may
cause some reception di
sturbance or flutter.
This problem occurs primarily in urban areas.
NOTE
 Reset the time after the 12V starter battery terminals are disconnect
ed and reconnected.
 Seconds do not appear
in the clock display,
but after adjusting the “minutes” setting, theclock begins to operate from 0 seconds.
General information about your radio
CAUTION Changes or modifica
tions not expressly
approved by the party meeting the aboveconditions could void the user’s authority tooperate the equipment.
Signal transmission FM AM 25 to 40 mile radius (25 to 40 miles)
100 mile radius (100 miles)
Weak reception (fading) Reflection
BK0209800US.book 23 ページ ２０１４年１月１４日　火曜日　午前９時２６分

Tire repair kit 8-8 For emergencies
8
7. Take the cap (D) off the tire sealant bottle (E). Do not remove the seal (F). Screw thefiller hose (G) onto th
e bottle (E). As you
screw the filler hose onto the bottle, the seal will break, allowing the sealant to beused.
8. Take the valve cap (H) off the tire valve (I), then press the valve remover (J) ontothe valve as illustrated. Allow all of the air in the tire to escape. 9. Remove the valve insert (K) by turning it counterclockwise usi
ng the valve remover
(J). Put the removed valve insert in a clean place so it
does not get dirty.
10. Remove the plug (L) from the free end of
the hose (M). Press the hose onto the valve (I).
CAUTION If you shake the bottle after screwing on the hose, sealant may spray out of the hose.
WA R N I N G If there is any air left in the tire when you remove the valve inse
rt, the valve insert
may fly out and injure you. Make sure thetire contains no air before removing the valve insert.NOTE
 Turn the valve remover by hand. If you use a tool, the valve remove
r could be damaged.
BK0209800US.book 8 ページ ２０１４年１月１４日　火曜日　午前９時２６分

Coolant/Hot water heater fluid
Vehicle care and maintenance 9-5
9
1. Open the liftgate. 2. Peel off the Velcro fastener (A) to remove the luggage room floor carpet (B).
3. Turn the 4 screws on the front and rear of the electric motor unit room lid (C) coun- terclockwise to loosen and remove them,and then remove the electric motor unit room lid (C).
4. Check the coolant level in the reservoir (D).While the motor is cold, the coolant level must always be between the “F (FULL)” and the “L (LOW)”
marks. If necessary,
add coolant. Refer to
“To add coolant” on
page 9-6. 5. Reinstall the electric motor unit room lid and the luggage room floor carpet by fol- lowing the removal procedures in reverse.
The reservoir (A) is located under the hood.
 The room under the h
ood and the electric
motor unit room (loc
ated under the lug-
gage room carpet) can be very hot afterdriving. Wait until they have cooled down.
Coolant
WA R N I N G
NOTE
 A heat insulating material is attached to the luggage room floor ca
rpet. To remove the
luggage floor carpet, grasp and lift up boththe carpet fabric and the heat insulating material.NOTE
 When laying the electric motor unit room lid on the ground, leave the underside of the lid with the rubber surface facing up. If theunderside is facing downward debris and other foreign material
could get on the rub-
ber surface and prevent proper reinstallationof the electric motor unit room lid.
WA R N I N G Never touch components inside the elec- tric motor unit room except the reservoir (D).
Hot water heater fluid
FULL LOW
BK0209800US.book 5 ページ ２０１４年１月１４日　火曜日　午前９時２６分

12V starter battery 9-8 Vehicle care and maintenance
9
N00901300054
1. Turn the plastic nut (A) counterclockwise, and then remove the 12V starter battery upper cover (B).
1. Install the 12V starter battery upper cover (B) onto the 12V starter battery, and then push the plastic nut (A) in the direction shown by the arrows to secure the cover.
N00901500069
Before checking the 12V starter battery elec-trolyte level, remove th
e 12V starter battery’s
upper cover. The electrolyte level
must be between the
limits shown on the outside of the 12V starterbattery. Fill it with distilled water as needed. The inside of the 12V starter battery is divided into several compartments. Take the cap off of each compartment and fill to the mark.Do not fill above the t
op line because a spill
during driving could cause damage.
Removing and installing the 12V starter battery upper cover To r e m o v e
NOTE
 Be careful not to lose the removed plastic nut.
To install
CAUTION Be sure to install the 12V starter battery upper cover. Otherwise,
the battery electro-
lyte may spill and
cause a malfunction.
When installing the 12V
starter battery upper
cover and plastic nut
do not touch the cool-
ing fan or other moving parts under the hood.Be especially carefu
l that the cables, your
clothing or hair, etc.,
do not get caught in the
cooling fan or ot
her moving parts.
NOTE
Be sure to install the plastic nut in the correct direction.
Checking 12V starter battery electrolyte level
WA R N I N G If the 12V starter battery goes flat, be sure to check the 12V star
ter battery electro-
lyte level before connecting booster cables.
BK0209800US.book 8 ページ ２０１４年１月１４日　火曜日　午前９時２６分

Replacement of light bulbs 9-24 Vehicle care and maintenance
9
2. Remove the socket and bulb assembly together by turning it counterclockwise. 3. Pull the bulb out of the socket.4. To install the bulb, perform the removal steps in reverse.
N00943401407
1. To create enough work space, turn the steering wheel all the way in the same direction to the side
you wish to replace.
2. Remove the clip (A) and bolts (B), then lift the cover (C).
NOTE
 When installing the light assembly, push in the end facing the front
of the vehicle first.
* : Front of the vehicle
Front turn signal lights/Front fog lights/Daytime running lights
BK0209800US.book 24 ページ ２０１４年１月１４日　火曜日　午前９時２６分

Replacement of light bulbs
Vehicle care and maintenance 9-25
9
3. Turn the socket counterclockwise to remove it.
4. Remove the bulb as follows. [Front turn signal light]Pull the bulb out of the socket. [Front fog light
and daytime running
light]While holding down the tab (G), pull out the bulb assembly (H).
5. To install the bulb, perform the removal steps in reverse.
N00943700487
1. Open the liftgate. (Refer to “Liftgate” on page 5-11.)
D- Front turn signal light E- Front fog light F- Daytime running light
Front turn signal light Front fog light Daytime running light
CAUTION Handle halogen light bul
b with care. The gas
inside a halogen light
bulb is highly pressur-
ized, so dropping, knocki
ng, or scratching a
halogen light bulb can
cause it to shatter.
Never hold the halogen
light bulb with a bare
hand, dirty glove, etc. The oil from your hand could cause the bulb to break the next time the fog lights are used.If the glass surface is dirty, clean it with alcohol and let it dry completely before installing the bulb.
Rear combination lights
BK0209800US.book 25 ページ ２０１４年１月１４日　火曜日　午前９時２６分

Replacement of light bulbs 9-26 Vehicle care and maintenance
9
2. Remove the screws (A) that hold the light unit and remove the light unit. 3. Move the light unit toward the rear of the vehicle and remove the pins (B) of the light unit from the vehicle.
4. Turn the socket counterclockwise to remove it.
5. Pull the bulb out of the socket. 6. To install the bulb, perform the removal steps in reverse.
N00935400108
1. Remove the clips (A), then lift the cover(B).
C- Tail and stop light (LED) - cannot be
replaced
D- Rear turn signal light E- Back up light
NOTE
 The tail and stop lights use LEDs rather than bulbs. For repair and replacem
ent, contact a certi-
fied i-MiEV dealer.
Rear side-marker lights
BK0209800US.book 26 ページ ２０１４年１月１４日　火曜日　午前９時２６分