2015 MERCEDES-BENZ C-Class SEDAN Page 41

Opening
You can open the trunk lid from the driver's
seat when the vehicle is stationary and
unlocked.
X Pull remote operating switch for trunk
lid 0043 until the trunk lid opens. Locking the trunk separately
You can lock the trunk separately. If you then
unlock the vehicle centrally, the trunk
remains locked and cannot be opened. Activating the function to lock the trunk sep-
arately:
X Close the trunk lid.
X Open the glove box.
X Push the switch to position 0043.
If the vehicle is unlocked centrally, the
trunk remains locked.
i You can also lock the glove box
(Y page 299). Deactivating the function to lock the trunk
separately:
X Open the glove box.
X Push the switch to position 0044.
If the vehicle is unlocked centrally, the
trunk will also be unlocked. Unlocking the trunk (mechanical key)
! The trunk lid swings upwards when
opened. Therefore, make sure that there is sufficient clearance above the trunk lid.
If the trunk cannot be unlocked with the
SmartKey, KEYLESS-GO or HANDS-FREE
ACCESS, use the mechanical key.
If you use the mechanical key to unlock and
open the trunk lid, the anti-theft alarm system will be triggered. Switch off the alarm
(Y page 76).
X Take the mechanical key out of the Smart-
Key (Y page 83).
X Insert the mechanical key into the trunk lid
lock as far as it will go. X
Turn the mechanical key counter-clockwise
as far as it will go from position 0047to posi-
tion 0048.
The trunk is unlocked.
X Turn the mechanical key back to position
0047 and remove it.
X Insert the mechanical key into the Smart-
Key (Y page 83).
When you lock the vehicle (Y page 89), the
trunk is also locked. 96
TrunkOpening and closing

Opening and closing the side win-
dows
The switches for all side windows are located
on the driver's door. There is also a switch on
each door for the corresponding side window.
The switches on the driver's door take prec-
edence. 0043
Front left
0044 Front right
0087 Rear right
0085 Rear left
X Turn the SmartKey to position 1or 2in the
ignition lock (Y page 157).
X To open manually: press and hold the cor-
responding switch.
X To open fully: press the switch beyond the
point of resistance and release it.
Automatic operation is started.
X To close manually: pull the corresponding
switch and hold it.
X To close fully: pull the switch beyond the
point of resistance and release it.
Automatic operation is started.
X To interrupt automatic operation:
press/pull the corresponding switch again.
If you press the switch beyond the point of
resistance and release, automatic operation
is started in the corresponding direction. You
can stop automatic operation by pressing/
pulling the switch again.
You can continue to operate the side windows after you switch off the engine or remove the SmartKey. This function remains active for
five minutes or until you open a front door.
When the override feature for the side win-
dows is activated (Y page 65), the side win-
dows cannot be operated from the rear.
i Information on opening and closing the
roller sunblinds on the rear side windows
(Y page 308). Convenience opening
General notes Vehicles with KEYLESS-GO or KEYLESS-
GO start function:
you can ventilate the vehi-
cle before you start driving.
If the SmartKey is in close proximity to the
vehicle, the convenience opening function is
available.
To do this, the SmartKey is used to carry out
the following functions simultaneously:
R unlock the vehicle
R open the side windows
R open the sliding sunroof or the panorama
roof with power tilt/sliding panel and the
roller sunblind
R switch on the seat ventilation for the driv-
er's seat
Convenience opening X
Press and hold the 0036button until the
side windows and the sliding sunroof or the
panorama roof with power tilt/sliding
panel are in the desired position.
If the roller sunblinds of the panorama roof
with power tilt/sliding panel are closed, the roller sunblinds are opened first.
X Press and hold the 0036button again until
the panorama roof with power tilt/sliding
panel is in the desired position.
X To interrupt convenience opening:
release the 0036button. 98
Side windowsOpening and closing

Convenience closing feature
Important safety notes G
WARNING
When the convenience closing feature is oper- ating, parts of the body could become trapped
in the closing area of the side window and the
sliding sunroof. There is a risk of injury.
Observe the complete closing procedure
when the convenience closing feature is oper-
ating. Make sure that no body parts are in
close proximity during the closing procedure.
Vehicles with KEYLESS-GO or KEYLESS-
GO start function: if the SmartKey is in close
proximity to the vehicle, the convenience
closing function is available.
When you lock the vehicle, you can simulta-
neously:
R close the side windows
R close the sliding sunroof or the panorama
roof with power tilt/sliding panel
On vehicles with a panorama roof with power tilt/sliding panel, you can then close the
roller sunblinds.
Notes on the automatic reversing feature for:
R the side window (Y page 97)
R the sliding sunroof or the panorama roof
with power tilt/sliding panel
(Y page 102)
Using the SmartKey X
Press and hold the 0037button until the
side windows and the sliding sunroof or the panorama roof with power tilt/sliding
panel are fully closed.
X Make sure that all the side windows and the
sliding sunroof or panorama roof with
power tilt/sliding panel are closed.
X Vehicles with panorama roof with
power tilt/sliding panel: press and hold
the 0037 button until the roller sunblinds of
the panorama roof with power tilt/sliding
panel close. X
To interrupt convenience closing:
release the 0037button.
Using KEYLESS-GO The driver's door and the door at which the
handle is used, must both be closed. The
SmartKey must be outside the vehicle. The
gap between the SmartKey and the corre-
sponding door handle should not be greater
than 3 ft (1 m). X
Touch recessed sensor surface 0043on the
door handle until the side windows and the sliding sunroof or the panorama roof with
power tilt/sliding panel are fully closed.
Make sure you only touch recessed sensor surface 0043.
X Make sure that all the side windows and the
sliding sunroof or panorama roof with
power tilt/sliding panel are closed.
X Vehicles with panorama roof with
power tilt/sliding panel: touch recessed
sensor surface 0043on the door handle again
until the roller sunblinds of the panorama
roof with power tilt/sliding panel close.
X To interrupt convenience closing:
release recessed sensor surface 0043on the
door handle. Resetting the side windows
If a side window can no longer be closed fully, you must reset it. Side windows
99Opening and closing Z

X
Close all the doors.
X Turn the SmartKey to position 1or 2in the
ignition lock (Y page 157).
X Pull the corresponding switch on the door
control panel until the side window is com-
pletely closed (Y page 98).
X Hold the switch for an additional second.
If the side window opens again slightly: X Immediately pull the corresponding switch
on the door control panel until the side win-
dow is completely closed (Y page 98).
X Hold the switch for an additional second.
X If the respective side window remains
closed after the button is released, then it
has been set correctly. If this is not the
case, repeat the steps above again. 100
Side windowsOpening and closing

X
Turn the SmartKey to position 1or 2in the
ignition lock (Y page 157).
X Press or pull the 0057switch in the corre-
sponding direction.
If you press or pull the 0057switch beyond
the point of resistance, automatic operation
is started in the corresponding direction. You can stop automatic operation by pressing or
pulling again.
When opening and raising the roof, automatic
operation is only available if the sliding sun-
roof is in the closed position.
The sun protection cover automatically opens along with the sliding sunroof. You can open
or close the sun protection cover manually
when the sliding sunroof is raised or closed.
You can continue to operate the sliding sun-
roof after switching off the engine or remov-
ing the SmartKey from the ignition lock. This
function is available for up to five minutes or
until the driver's or front-passenger door is
opened.
Resetting !
If the sliding sunroof still cannot be
opened or closed fully after resetting, con- tact a qualified specialist workshop.
Reset the sliding sunroof if it does not move
smoothly. X Turn the SmartKey to position 1or 2in the
ignition lock.
X Raise the sliding sunroof fully at the rear
(Y page 102).
X Keep the 0057switch pressed for another
second.
X Make sure that the sliding sunroof can be
fully opened and closed again
(Y page 102).
X If this is not the case, repeat the steps
above again. Operating the panorama roof with
power tilt/sliding panel
Opening and closing Overhead control panel
0043
To raise
0044 To open
0087 To close/lower
The panorama roof with power tilt/sliding
panel can only be operated when the roller
sunblind is open.
X Turn the SmartKey to position 1or 2in the
ignition lock (Y page 157).
X Press or pull the 0057switch in the corre-
sponding direction.
If you press or pull the 0057switch beyond
the point of resistance, automatic operation
is started in the corresponding direction. You can stop automatic operation by pressing or
pulling again.
If the panorama roof with power tilt/sliding
panel is raised at the rear, it automatically
lowers slightly at higher speeds. The noise
level in the vehicle interior is reduced as a
result. At low speeds it raises again automat-
ically.
You can continue to operate the panorama
roof with power tilt/sliding panel after you
switch off the engine or remove the Smart-
Key. This function remains active for five
minutes or until you open a front door.
When a roof carrier is mounted the panorama
roof with power tilt/sliding panel cannot be
opened. The panorama roof with power tilt/ Sliding sunroof
103Opening and closing Z

sliding panel can still be raised to allow ven-
tilation of the vehicle interior. If the panorama
roof with power tilt/sliding panel makes con- tact with a roof carrier approved by
Mercedes-Benz, the sunroof will lower slightly
but remain raised at the rear.
Rain-closing feature The raised sliding sunroof automatically low-
ers at the rear when driving if it starts to rain.
The sliding sunroof is lowered depending on:
R the road speed and
R the intensity of the rain.
You can manually cancel the automatic clos-
ing procedure. Press or pull the 0057switch
in any direction.
To raise the sliding sunroof again, press the
0057 switch in direction 0043.
The "Rain-closing feature when driving" func- tion is deactivated, until you:
R press or pull the 0057switch in any direc-
tion or
R turn the SmartKey to another position in
the ignition lock (Y page 157).Operating the roller sunblinds for the
panorama roof with power tilt/sliding panel
Important safety notes G
WARNING
When opening or closing the roller sunblind,
parts of the body could be trapped between
the roller sunblind and the frame or sliding
sunroof. There is a risk of injury.
When opening or closing make sure that no
parts of the body are in the sweep of the roller sunblind.
If somebody becomes trapped:
R release the switch immediately, or
R during automatic operation, push the
switch briefly in any direction The opening or closing procedure will be stop-
ped.
The roller sunblinds shield the vehicle interior from sunlight. The front roller sunblind can
only be opened and closed when the sliding
sunroof is closed.
Roller sunblind reversing feature The roller sunblinds are equipped with an
automatic reversing feature. If a solid object
blocks or restricts a roller sunblind during the closing process, the roller sunblind opens
again automatically. However, the automatic
reversing feature is only an aid and does not
relieve you of the responsibility of paying
attention when closing the roller sunblinds. G
WARNING
The reversing feature especially does not
react to soft, light and thin objects such as
small fingers. This means that the reversing
feature cannot prevent someone being trap-
ped in these situations. There is a risk of
injury.
When closing make sure that no parts of the
body are in the sweep of the roller sunblind.
If somebody becomes trapped:
R release the switch immediately, or
R during automatic operation, push the
switch briefly in any direction
The closing process is stopped. 104
Sliding sunroofOpening and closing

Opening and closing the roller sun-
blinds Overhead control panel
0043
To open
0044 To open
0087 To close
You can only close the roller sunblinds when
the panorama roof with power tilt/sliding
panel is closed.
X Turn the SmartKey to position 1or 2in the
ignition lock (Y page 157).
X Press the 0057switch in direction 0043.
Both roller sunblinds open, then the pano-
rama roof with power tilt/sliding panel is
raised.
X Pull the 0057switch in direction 0044.
The sunblinds open
X Pull the 0057switch in direction 0087.
The roller sunblinds close when the pano-
rama roof with power tilt/sliding panel is
closed.
If you press or pull the 0057switch beyond
the point of resistance, automatic operation
is started in the corresponding direction. You
can stop automatic operation by pressing or
pulling again. Resetting the panorama roof with
power tilt/sliding panel or the front
roller sunblind
Reset the panorama roof with power tilt/slid-
ing panel or the front roller sunblind if the
panorama roof with power tilt/sliding panel
or the roller sunblinds does not move
smoothly.
X Turn the SmartKey to position 1or 2in the
ignition lock (Y page 157).
X Pull the 0057switch repeatedly to the point
of resistance in the direction of arrow 0043
until the panorama roof with power tilt/
sliding panel is fully closed.
X Keep the 0057switch pulled for an addi-
tional second.
X Pull the 0057switch in the direction of
arrow 0043repeatedly until the front roller
sunblind is closed.
X Keep the 0057switch pulled for an addi-
tional second.
X Make sure that the panorama roof with
power tilt/sliding panel (Y page 103) and
the front roller sunblind (Y page 105) can
be fully opened again.
X If this is not the case, repeat the steps
above again. Sliding sunroof
105Opening and closing Z

Useful information
i This Operator's Manual describes all
models and all standard and optional equip- ment of your vehicle available at the time of
publication of the Operator's Manual.
Country-specific differences are possible.
Please note that your vehicle may not be
equipped with all features described. This
also applies to safety-related systems and
functions.
i Read the information on qualified special-
ist workshops (Y page 26). Correct driver's seat position
G
WARNING
You could lose control of your vehicle if you do the following while driving:
R adjust the driver's seat, head restraint,
steering wheel or mirrors
R fasten the seat belt
There is a risk of an accident.
Adjust the driver's seat, head restraint, steer-
ing wheel and mirror and fasten your seat belt before starting the engine. X
Observe the safety guidelines on seat
adjustment (Y page 109).
X Make sure that seat 0087is adjusted prop-
erly.
Electrical seat adjustment (Y page 110)
When adjusting the seat, make sure that:
R you are as far away from the driver's air bag
as possible
R you are sitting in a normal upright position
R you can fasten the seat belt properly
R you have moved the backrest to an almost
vertical position
R you have set the seat cushion angle so that
your thighs are gently supported
R you can depress the pedals properly.
R your legs are not fully extended
X Check whether the head restraint is adjus-
ted properly.
When doing so, make sure that you have
adjusted the head restraint so that the back
of your head is supported at eye level by the center of the head restraint.
X Observe the safety guidelines on steering
wheel adjustment (Y page 115).
X Make sure that steering wheel 0043is adjus-
ted properly.
Adjust the steering wheel manually
(Y page 115)
Adjust the steering wheel electrically
(Y page 116)
When adjusting the steering wheel, make
sure that:
R you can hold the steering wheel with your
arms slightly bent
R you can move your legs freely
R you can see all the displays in the instru-
ment cluster clearly
X Observe the safety guidelines for seat belts
(Y page 44).
X Check whether you have fastened seat
belt 0044properly (Y page 46).108
Correct driver's seat positionSeats, steering wheel and mirrors