2015 MERCEDES-BENZ C-CLASS COUPE brake

Safety systems
Warning/
indicator
lamp
N N
Signal type
Possible causes/consequences and M
MSolutions J
N
The yellow brake system warning lamp lights up while the engine is running or
the ECO start/stop function is activated.
G WARNING
The brake system is malfunctioning and the braking characteristics may be affec- ted.
There is arisk of an accident.
X If the multifunction display shows adisplay message, please observe this.
X Drive on carefully.
X Consult aqualified specialist workshop immediately. J
N
The red brake system warning lamp is lit while the engine is running.
Aw arning tone also sounds.
G WARNING
The brake boosting effect is malfunctioning and the braking characteristics may be
affected.
There is arisk of an accident.
X Pull over and stop the vehicle safely as soon as possible, paying attention to road
and traffic conditions. Do not continue driving under any circumstances.
X Safeguard the vehicle against rolling away (Y page 172).
X Consult aqualified specialist workshop.
X Observe the additional display messages in the multifunction display. J
N
The red brake system warning lamp is lit while the engine is running.
Aw arning tone also sounds.
There is insufficient brake fluid in the brake fluid reservoir.
G WARNING
Braking efficiency may be impaired.
There is arisk of an accident.
X Pull over and stop the vehicle safely as soon as possible, paying attention to road
and traffic conditions. Do not continue driving under any circumstances.
X Safeguard the vehicle against rolling away (Y page 172).
X Do not top up the brake fluid. Topping up will not rectify the fault.
X Consult aqualified specialist workshop.
X Observe the additional display messages in the multifunction display. 286
Warning and indicator lampsint
he instrument clusterOn-board computer and displays

Warning/
indicator
lamp
N N
Signal type
Possiblec auses/consequences and M
MSolutions !
N
The yellow ABS warning lamp is lit while the engine is running.
ABS (Anti-lock Braking System) is faulty.
An additiona lwarning tone indicates that EBD (electronic brake force distribution)
is faulty.
Other driving and driving safety systems may alsobef aulty.
G WARNING
The brake system continues to function normally, but without the functions listed above. The front and rear wheels coul dtherefore lock, for example, if you brake
hard.
The steerability and braking characteristics may be severely affected. The braking
distance may increas einanemergency braking situation.
If ESP ®
is not operational ,ESP ®
is unable to stabilise the vehicle.
There is an increased dange rofskidding and risk of an accident.
X Observe the additiona ldisplay messages in the multifunction display.
X Drive on carefully.
X Consult aqualified specialist worksho pimmediately.
If the ABS control unit is faulty, there is alsoap ossibility that other systems,such
as the navigation system or the automatic transmission, willbeu navailable.J÷
!
N
The red brake system warning lamp and the yellow ESP ®
and ABS warning lamps
light up while the engine is running.
ABS and ESP ®
are faulty.
Other driving and driving safety systems may alsobef aulty.
G WARNING
The brake system continues to function normally, but without the functions listed above. The front and rear wheels coul dtherefore lock, for example, if you brake
hard.
The steerability and braking characteristics may be severely affected. The braking
distance may increas einanemergency braking situation.
If ESP ®
is not operational ,ESP ®
is unable to stabilise the vehicle.
There is an increased dange rofskidding and risk of an accident.
X Observe the additiona ldisplay messages in the multifunction display.
X Drive on carefully.
X Consult aqualified specialist worksho pimmediately. Warning and indicator lamps in the instrument cluster
287On-board computer and displays Z

Warning/
indicator
lamp
N N
Signal type
Possiblec auses/consequences and M
M Solutions ÷
N
The yellow ESP ®
warning lamp flashes while the vehicl eisinmotion.
ESP ®
or traction control has intervened because there is arisk of skidding or at
least one whee lhas started to spin.
Cruise control or DISTRONIC PLUS is deactivated.
X Only depress the accelerator peda lasfar as necessary when pulling away.
X Accelerate more gently while the vehicl eisinmotion.
X Adapt yourd riving style to suitt he road and weather conditions.
X Do not deactivate ESP ®
.
In rare cases it may be better to deactivate ESP ®
:
R all vehicles except Mercedes-AMG vehicles (Y page72)
R Mercedes-AMG vehicles (Y page73)
Observe the important safety notes on ESP ®
(Y page7 2). ÷
N
The yellow ESP ®
warning lamp is lit while the engine is running.
ESP ®
is faulty.
Other driving and driving safety systems may alsobef aulty.
G WARNING
The brake system continues to function normally, but without the functions listed above.
The braking distance may thus increas einanemergency braking situation.
If ESP ®
is not operational ,ESP ®
is unable to stabilise the vehicle.
There is an increased dange rofskidding and risk of an accident.
X Observe the additiona ldisplay messages in the multifunction display.
X Drive on carefully.
X Consult aqualified specialist worksho pimmediately. 288
Warning and indicator lamps in the instrument clusterOn-board computer and displays

Warning/
indicator
lamp
N N
Signal type
Possiblec auses/consequences and M
M Solutions !
N
The red indicator lamp for the electric parking brake flashes or is lit and/or the
yellow warning lamp for the electric parking brake is lit.
X Observe the additiona ldisplay messages in the multifunction display. 6
N
The red restraint system warning lamp is lit while the engine is running.
The restraint system is faulty.
G WARNING
The airbags or beltt ensioners may either be triggere dunintentionally or, in the
event of an accident, may not be triggered.
This poses an increased risk of injury.
X Observe the additiona ldisplay messages in the multifunction display.
X Drive on carefully.
X Contact aqualified specialist worksho pimmediatel yand have the restraint sys-
tem checked.
For further information about the restraint system, see (Y page39). Engine
Warning/
indicator
lamp
N N
Signal type
Possiblec auses/consequences and M
M Solutions ;
N
The yellow engine diagnostics warning lamp lights up while the engine is run-
ning.
There may be afault, for example:
R in the engine management
R in the fuel injection system
R in the exhaust system
R in the ignitio nsystem (for vehicles with petrol engines)
R in the fuel system
The emission limi tvalues may be exceede dand the engine may be running in
emergency mode.
X Consult aqualified specialist worksho pimmediately.
Vehicles with adiesel engine: the fuel tank has been run dry (Y page169).
X Start the engine three to four times after refuelling.
If the yellow engine diagnostics warning lamp goes out, emergency running
mode is cancelled. The vehicl eneed not be checked. 8
N
The yellow reserve fuel warning lamp is on while the engine is running.
The fuel leve lhas dropped into the reserve range.
Operation of the auxiliary heating is deactivated if the fuel leve ldrops into the
reserve range.
X Refuel at the neares tfilling station. 290
Warning and indicator lamps in the instrument clusterOn-board computer and displays

Warning/
indicator
lamp
N N
Signal type
Possiblec auses/consequences and M
MSolutions X
Make sure that the air supply to the engine radiator is not blocked ,e.g. by frozen
slush.
X If the coolant temperature is below 120 †, you can continue driving to the
neares tqualified specialist workshop.
X Avoid heavy loads on the engine as you do so, e.g. driving in mountainous terrain
and stop-start traffic. Driving systems
Warning/
indicator
lamp
N N
Signal type
Possiblec auses/consequences and M
MSolutions ·
N
The red distance warning lamp lights up while the vehicl eisinmotion.
The distance to the vehicl einfront is too smal lfor the spee dselected.
X Increase the distance. ·
N
The red distance warning lamp lights up while the vehicl eisinmotion.Awarning
tone alsos ounds.
You are approaching avehicle, apedestrian or astationary obstacl einyourline of
travel at too high aspeed.
X Be prepared to brake immediately.
X Pay carefu lattention to the traffic situation. You may have to brake or take
evasive action.
Further information on PRE ‑SAFE®
Brake (Y page75).
For further information on the distance warning function of COLLISION PREVEN-
TION ASSIST PLUS, see (Y page69). Warning and indicator lamps in the instrument cluster
293On-board computer and displays Z

X
Press 9or: on the steerin gwheel to
select the Service
Servicemenu and confirm with
a.
X Press 9or: on the steerin gwheel to
select the ASSYST PLUS
ASSYST PLUS submenu and con-
firm with a.
The service due date appears in the multi-
function display. Information about service
Resetting the ASSYST PLUS service
interva ldisplay !
If the ASSYST PLUS service interval display
has been inadvertently reset, this setting can
be corrected at aqualified specialist work-
shop.
Have service work carried out as described in the Servic eBooklet .This may otherwise lead
to increased wear and damage to the major
assemblies or the vehicle.
Aq ualified specialist workshop, e.g. a
Mercedes-Benz Servic eCentre, will reset the
ASSYST PLUS service interval display after the
service work has been carried out. You can also
obtain further information on maintenance
work, for example.
Special service requirements The prescribed service interval is based on nor-
mal operation of the vehicle. Servic ework will
need to be performed more often if the vehicle is
operated under arduous conditions or increased loads, for example:
R regular city driving with frequent intermediate
stops
R if the vehicle is primarily used to travel short
distances
R for frequent operation in mountainous terrain
or on poor road surfaces
R if the engine is often left idling for long periods
In these or similar operating conditions, have,
for example, the air filter, engine oil and oil filter changed more frequently. The tyres must be
checked more frequently if the vehicle is oper-
ated under increased loads. Further informationcan be obtained at aqualified specialist work-
shop, e.g. aMercedes-Benz Servic eCentre. Driving abroad An extensive Mercedes-Benz Servic
enetwor kis
also availabl einother countries. You can obtain
further information from any Mercedes-Benz
Servic eCentre. Care
General notes
H
Environmenta
lnote
Dispose of empty packaging and cleaning
cloths in an environmentally responsible man-
ner.
! For cleaning your vehicle, do not use any of
the following:
R dry, rough or hard cloths
R abrasive cleaning agents
R solvents
R cleaning agents containing solvents
Do not scrub.
Do not touch the surfaces or protective films
with hard objects, e.g. aring or ice scraper.
You could otherwise scratch or damage the
surfaces and protective film.
! Do not park up the vehicle for an extended
period straight after cleaning it, particularly
after having cleaned the wheels with wheel
cleaner. Wheel cleaners could cause
increased corrosion of the brake discs and
brake pads/linings. For this reason, you
should drive for afew minutes after cleaning.
Brakin gheats the brake discs and the brake
pads/linings, thus drying them. The vehicle
can then be parked up.
Regula rcare of your vehicle is acondition for
retainin gthe quality in the long term.
Use care products and cleaning agents recom-
mended and approved by Mercedes-Benz. 326
CareMaintenance and care

Washing the vehiclea
nd cleaning the
paintwork
Automatic car wash G
WARNING
Braking efficiency is reduced after the vehicle has been washed .There is arisk of an acci-
dent.
After washing the vehicle, brake carefully
while paying attention to the traffic conditions in order to restore full braking efficiency.
! When DISTRONIC PLUS or the HOLD func-
tion is activated, the vehicl ebrakes automat-
ically in certain situations.
To avoi ddamage to the vehicle, deactivate
DISTRONIC PLUS and the HOLD function in
the following or similar situations:
R when towing away
R in ac ar wash
! Make sure:
R the side windows and sliding sunroo fare
close dcompletely.
R the blower for the ventilation/heating is
switched off (OFF button is depressed).
R the windscreen wiper switch is at position
0
R the 360° camera or reversing camera is
switched off.
The vehicl ecouldo therwise be damaged.
! If the key is withi
nthe rear detection range
of KEYLESS-GO, the following situations, for
example, coul dleadtot he boot lid opening
unintentionally:
R using acar wash
R using ahigh-pressure cleaner
Make sure that the key is at least 3maway
from the vehicle.
! Make sure that the automatic transmission
is in neutral position Nwhen washing your
vehicl einat ow-through car wash. The vehicle
may otherwise be damaged.
R Operating with the key:
Do not remove the key from the ignition
lock. Do not open the driver's door when
the engine is switched off or at very low
speeds. Otherwise, whe nintransmission position
Dor Rthe automatic transmission
wil lautomatically switch to park position P
and block the wheels.
R Operating with the Start/Stop button:
Do not open the driver's door whe nthe
engine is switched off or at very low
speeds. Otherwise, whe nintransmission
position Dor Rthe automatic transmission
wil lautomatically switch to park position P
and block the wheels.
Observe the following to make sure that the
automatic transmission stay sinneutral position
N:
Operating with the key and Start/Stop button:
X Make sure the ignition is switched on.
X Make sure that the vehicl eisstationary.
X Depress the brake peda land keep it
depressed.
Operating with the Start/Stop button only: X Engage park position P.
X Releas ethe brake pedal.
X Remove the Start/Stop button from the igni-
tion lock (Y page145).
X Insert the key into the ignition lock.
X Switch on the ignition.
X Depress the brake peda land keep it
depressed.
Operating with the key and Start/Stop button:
X Select neutral N.
X Releas ethe brake pedal.
X Releas ethe electric parking brake, if neces-
sary.
X Switch off the ignition and leave the key in the
ignition lock.
You can wash the vehicl einanautomatic car
wash from the very start.
Was hoff excess dirt before cleaning the vehicle
in an automatic car wash.
After using an automatic car wash, wip eoff wax
from the windscreen and the wiper blades. This
wil lprevent smears and reduce wiping noises
caused by residue on the windscreen.
Washing by hand In some countries
,washing by hand is only
allowe datspeciall yequipped washing bays. Care
327Maintenance and care Z

Observe the legal requirements for each indi-
vidualc ountry.
X Do not use hot water and do not wash the
vehicle in direct sunlight.
X Use asoft sponge to clean.
X Use amild cleaning agent, such as acar
shampoo approved by Mercedes-Benz.
X Thoroughly hose down the vehicle with agen-
tle jet of water.
X Do not point the water jet directly towards the
air inlet.
X Use plenty of water and rinse out the sponge
frequently.
X Rinse the vehicle with clean water and dry
thoroughly with achamois.
X Do not let the cleaning agent dry on the paint-
work.
When using the vehicle in winter, remove all
traces of road salt deposits carefully and as
soon as possible.
High-pressure cleaning equipment G
WARNING
The water jet of circular-jet nozzles (dirt grind- ers) can cause damage not visible from the
outside to tyres or chassis components. Com-
ponents damaged in this way can unexpect-
edly fail. There is arisk of an accident.
Do not use high-pressure cleaners with circu-
lar-jet nozzles to clean the vehicle. Have dam- aged tyres or chassis componentsr eplaced
immediately.
! Alwaysm
aintainadistance of at least 30 cm
between the vehicle and the high-pressure
cleaner nozzle. Information aboutt he correct
distance is available from the equipment
manufacturer.
Move the high-pressure cleaner nozzle
around when cleaning your vehicle.
Do not aim directly at any of the following:
R tyres
R door gaps, roof gaps, joints etc.
R electrical components
R battery
R connectors
R lights
R seals R
trim elements
R ventilation slots
Damaged seals or electrical componentsc an
lead to leaks or failures.
! If the key is within the rear detection range
of KEYLESS-GO, the following situations, for
example, could lead to the boot lid opening
unintentionally:
R using acar wash
R using ahigh-pressure cleaner
Make sure that the key is at least 3maway
from the vehicle.
! Edition
1special model: parts of your vehi-
cle are covered with adecorative foil. Main-
tain adistance of at least 70 cm between the
foil-wrappedp arts of the vehicle and the noz-
zle of the high pressure cleaner.
Information aboutt he correct distance is
available from the equipment manufacturer.
Move the high-pressure cleaner nozzle
around when cleaning your vehicle.
Cleaning the paintwork !
Do not affix:
R stickers
R films
R magnetic plates or similari tems
to painted surfaces. You could otherwise
damage the paintwork.
Scratches, corrosive deposits, areas affected by
corrosion and damage caused by inadequate
care cannot always be completely repaired. In
such cases, visit aqualified specialist workshop.
X Remove impurities immediately,w here pos-
sible, whilst avoiding rubbing too hard.
X Soak insect remains with insect remover and
rinse off the treated areas afterwards.
X Soak bird droppings with water and rinse off
the treated areas afterwards.
X Remove coolant, brake fluid, tree resins, oils,
fuels and greases by rubbing gently with a
cloth soaked in petroleum ether or lighter
fluid.
X Use tar remover to remove tar stains.
X Use silicone remover to remove wax. 328
CareMaintenance and care