2015 MAZDA MODEL CX-3 display

4–43
When Driving
Instrument Cluster and Display
Glow Indicator Light
(SKYACTIV-D 1.5)
This light may illuminate when the
ignition is switched ON.
It turns off when the glow plugs are warm.
If the ignition is left switched ON for a
long period of time without the engine
running after the glow plugs are warmed
up, the glow plugs may warm up again
which will illuminate the glow indicator
light.
$9@&;&&%@&EJUJPOJOEC







4–45
When Driving
Transaxle
NOTE
 (For vehicles with type B
instrument cluster *1 ) If the engine speed is about to exceed
the permissible engine speed, the
buzzer sounds.
 Refer to Over Rev. Buzzer on page
7-54 .
*1 To determine which instrument
cluster is equipped on your
Mazda, Refer to Meters and
Gauges on page 4-23 .


 If shifting to R is diffi cult, shift back
into neutral, release the clutch pedal,
and try again.
  (With i-stop function)  If the engine has stopped due to
stalling, it can be restarted by
depressing the clutch pedal within 3
seconds of the engine stopping.
 The engine cannot be restarted even
if the clutch pedal is depressed under
the following conditions:
 


 The driver's door is open.



 The driver's seat belt is unfastened.



 The clutch pedal is not released
completely after the engine stalled.
 


 The clutch pedal is depressed with
the engine not stopped completely.
Gear Shift Indicator
The gear shift indicator supports you to
obtain optimum fuel economy and smooth
driving. It displays the selected gear
position in the instrument cluster as well
as notifi es the driver to change to the most
suitable gear position corresponding to the
actual driving condition.
Selected gear position Suitable gear position
Indication Condition
Numeral The selected gear position is
displayed.
and numeral Shift up or down to the indicated
gear position is recommended.
CAUTION
Do not rely solely on the shift-up/
shift-down recommendations by
indications. The actual driving situation
might require shift operations different
from indication. To avoid the risk of
accidents, the road and traffi c conditions
have to be judged correctly by the driver
before shifting.
$9@&;&&%@&EJUJPOJOEC







4–48
When Driving
Transaxle
Shift Position Indication
The selector position is indicated when the
ignition is switched ON.
NOTE
If one of the following actions is
performed, the selector position is
displayed for 5 minutes even if the
ignition switch is in a position other than
ON.
 
 The ignition is switched OFF. 
 The driver's door is opened.
Gear position indication
In manual shift mode, the “M” of the shift
position indication illuminates and the
numeral for the selected gear is displayed.
Warning Light
The warning light turns on when the
system has a malfunction.
Refer to Warning Lights on page 4-37 .
Transaxle Ranges
 












 The shift position indicator light in the
instrument cluster illuminates. Refer to
Warning/Indicator Lights on page 4-36 .
 


 The selector lever must be in P or N to
operate the starter.
P (Park)
P locks the transaxle and prevents the front
wheels from rotating.
WARNING
Always set the selector lever to P and
set the parking brake:
Only setting the selector lever to the
P position without using the parking
brake to hold the vehicle is dangerous.
If P fails to hold, the vehicle could
move and cause an accident.
CAUTION
  Shifting into P, N or R while the
vehicle is moving can damage your
transaxle.
  Shifting into a driving gear or reverse
when the engine is running faster
than idle can damage the transaxle.
R (Reverse)
In position R, the vehicle moves only
backward. You must be at a complete
stop before shifting to or from R, except
under rare circumstances as explained in
Rocking the Vehicle (page 3-49 ).
N (Neutral)
In N, the wheels and transaxle are not
locked. The vehicle will roll freely even
on the slightest incline unless the parking
brake or brakes are on.
$9@&;&&%@&EJUJPOJOEC







*Some models.4–52
When Driving
Transaxle
Gear Shift Indicator *
The gear shift indicator supports you to
obtain optimum fuel economy and smooth
driving. It displays the selected gear
position in the instrument cluster as well
as notifi es the driver to change to the most
suitable gear position corresponding to the
actual driving condition.
Selected gear position Suitable gear position
Indication Condition
Numeral The selected gear position is
displayed.
and numeral Shift up or down to the indicated
gear position is recommended.
CAUTION
Do not rely solely on the shift-up/
shift-down recommendations by
indications. The actual driving situation
might require shift operations different
from indication. To avoid the risk of
accidents, the road and traffi c conditions
have to be judged correctly by the driver
before shifting.
NOTE
The gear shift indicator turns off when
the following operations are performed.
 
 The vehicle is stopped. 
 Manual shift mode is cancelled.
Manually shifting up
You can shift gears up by operating the
shift lever or the steering shift switches
* .
M1
: M2
: M3
: M4
: M5
: M6
Using selector lever
To shift up to a higher gear, tap the shift
lever back
once.
$9@&;&&%@&EJUJPOJOEC







4–87
When Driving
i-ELOOP
i-ELOOP Indicator Light/Control
Status Display
The driver is notifi ed of the i-ELOOP
power generating status and the vehicle
conditions by the i-ELOOP indicator light
(green) and the control status display.
i-ELOOP Indicator Light (Green)
(vehicle without type C/type D audio)
The light turns on during power
generation.
Control status display (vehicles with
type C/type D audio)
The i-ELOOP power generating status is
displayed in the centre display.
Refer to Control Status Display on page
4-89 .
$9@&;&&%@&EJUJPOJOEC







*Some models.4–88
When Driving
Fuel Economy Monitor
Fuel Economy Monitor *
For vehicles with type C/type D audio, the Control Status, Fuel Consumption, and
Effectiveness are switched and displayed by operating each icon in the display.
In addition, after completing a trip, the total energy effi ciency to date is displayed in the
ending display when the ending display is turned on.
1. Select the
icon on the home screen to display the applications screen.
2. Select the “Fuel Economy Monitor”.
3. Operate the commander switch or touch the screen and display the menu.
NOTE
When the menu is displayed by touching the screen, the display is hidden automatically
after 6 seconds.
4. Select the icon in the menu and perform the operation. Each icon operates as follows:
Indication on display Control status
Hides the menu display.
Displays the application screen.
Switches the Fuel Economy Monitor in the order of
Control Status, Fuel Consumption, and
Effectiveness.
Resets the fuel economy data.
Displays the following setting screen. Ending display on/off switching On/off switching for function which synchronizes
reset fuel economy data to trip meter (Trip A)
$9@&;&&%@&EJUJPOJOEC







4–89
When Driving
Fuel Economy Monitor
Fuel Consumption Display
Information regarding the fuel economy is displayed.
Indication on display Control status
Displays the fuel economy for the past 60 minutes. Displays the fuel economy every minute for the
past 1 to 10 minutes.
Displays the fuel economy every 10 minutes for the
past 10 to 60 minutes.
Displays the average fuel economy over the past 5
resets and after the current reset.
Calculates the average fuel economy every minute
after vehicle travel begins, and displays it.
NOTE
  The fuel economy data can be reset by doing the following operation:




 Press the reset switch from the menu screen.



 When the function which synchronizes the fuel economy monitor and the trip meter
is on, reset trip A of the trip meter.
 


 Delete the average fuel economy information displayed in the trip computer. 

 After resetting the fuel economy data, “-- -” is displayed while the average fuel
economy is calculated.
Control Status Display
The i-stop operation status and the i-ELOOP power generating status are displayed.
Indication on display Control status
With i-ELOOP system
Displays the level of electricity generated by
regenerative braking.
Displays the amount of the electricity stored in the
rechargeable battery.
$9@&;&&%@&EJUJPOJOEC







4–90
When Driving
Fuel Economy Monitor
Indication on display Control status
With i-ELOOP system
Displays the status of the electricity stored in the
rechargeable battery and being supplied to the
electrical devices (whole vehicle in display is
illuminated simultaneously).
Displays the accumulated fuel economy.
With i-ELOOP system
Without i-ELOOP system
Displays the readiness status as to whether operation
of the i-stop function is available.
Displays the operation readiness status of the i-stop
function on the vehicle side (engine, battery, and
A/C) using icon colouring. The blue colour indicates
that the i-stop function is ready to operate, and the
grey colour indicates that it is not ready for
operation.
$9@&;&&%@&EJUJPOJOEC