2015 MAZDA MODEL CX-3 roof

4–142
When Driving
i-ACTIVSENSE
NOTE
  The Smart City Brake Support (SCBS) detects a vehicle ahead by emitting a near-
infrared laser beam and receiving the beam refl ected off the refl ector of the vehicle
ahead, and then using it for the measurement. Consequently, the Smart City Brake
Support (SCBS) may not operate under the following conditions:
 


 Refl ection of the laser is poor due to the shape of the vehicle ahead.



 The vehicle ahead is signifi cantly dirty.



 Under bad weather condition, such as rain, fog and snow.



 The window washer is being used or the windscreen wipers are not used when it's
raining.
 


 The windscreen is dirty.



 The steering wheel is turned completely left or right, or the vehicle is accelerated
rapidly and comes close to the vehicle ahead.
 


 Trucks with low loading platforms and vehicles with an extremely low or high
profi le.




 Vehicles with certain shapes such as a vehicle carrier. 

 Under the following conditions, the Smart City Brake Support (SCBS) system may not
operate normally.
 


 Heavy luggage is loaded in the luggage compartment or on the rear seat.



 If there is the possibility of partial contact with a vehicle ahead.



 When driving on continuously curving roads, and entering and exiting exits.



 Elongated luggage or cargo is loaded onto installed roof rails and covers the laser
sensor (front) .
 


 Exhaust gas from the vehicle in front, sand, snow, and water vapour rising from
manholes and grating, and water splashed into the air.
 


 When towing a malfunctioning vehicle.



 When driving with tyres having signifi cantly different wear. 

 In the following cases, the laser sensor (front) may inadvertently determine that there
is a vehicle ahead and the Smart City Brake Support (SCBS) system may operate.
 


 Objects on the road at the entrance to a curve.



 Vehicles passing in the opposite lane while making a curve.



 Metal objects, bumps, or protruding objects on the road.



 When passing through a toll gate equipped with a bar.



 When passing under a vinyl curtain or fl ag.



 Plastic objects such as pylons.



 Two-wheeled vehicles, pedestrians, animals or standing trees. 

(Manual transaxle) If the vehicle is stopped by the SCBS operation and the clutch pedal is not depressed,
the engine stops.
$9@&;&&%@&EJUJPOJOEC







4–155
When Driving
i-ACTIVSENSE
Laser sensor radiation data
Maximum average power:45 mW
Pulse duration:33 ns
Wavelength:905 nm
Divergence angle (horizontal×vertical):28 degrees×12 degrees
NOTE
  In the following cases, the laser sensor (front) cannot detect vehicles ahead correctly,
and each system may be unable to operate normally.
 


 The windscreen is dirty.



 Elongated luggage or cargo is loaded onto installed roof rails and covers the laser
sensor (front).
 


 Exhaust gas from the vehicle in front, sand, snow, and water vapour rising from
manholes and grating, and water splashed into the air.
 
 If there are recognizable cracks or damage caused by fl ying gravel or debris on the
windscreen, always have the windscreen replaced. Consult an Authorised Mazda
Repairer for replacement.
$9@&;&&%@&EJUJPOJOEC







*Some models.4–16 8
When Driving
Rear View Monitor
Rear View Monitor *
The rear view monitor provides visual images of the rear of the vehicle when reversing.
WARNING
Always drive carefully confi rming the safety of the rear and the surrounding conditions
by looking directly with your eyes:
Reversing the vehicle by only looking at the screen is dangerous as it may cause an
accident or a collision with an object. The rear view monitor is only a visual assist
device when reversing the vehicle. The images on the screen may be different from the
actual conditions.
CAUTION
  Do not use the rear view monitor under the following conditions: Using the rear view
monitor under the following conditions is dangerous and could result in injury or
vehicle damage or both.
 


 Icy or snow-covered roads.



 Tyre chains or a temporary spare tyre is installed.



 The liftgate is not fully closed.



 The vehicle is on a road incline. 

 When the display is cold, images may course across the monitor or the screen and
may be dimmer than usual, which could cause diffi culty in confi rming the surrounding
conditions of the vehicle. Always drive carefully confi rming the safety of the rear and
the surrounding conditions by looking directly with your eyes.
  Do not apply excessive force to the camera. The camera position and angle may
deviate.
  Do not disassemble, modify, or remove it as it may no longer be waterproof. 
 The camera cover is made of plastic. Do not apply degreasing agents, organic solvents,
wax, or glass coating agents to the camera cover. If any are spilled on the cover, wipe
off with a soft cloth immediately.
  Do not rub the cover excessively, or polish it using an abrasive compound or a hard
brush. The cover may be damaged affecting the image.
$9@&;&&%@&EJUJPOJOEC







5–104
Interior Features
Bluetooth®
Ending Voice Recognition
Use one of the following methods:
 


 Press and hold the talk-button.



 Press the hang-up button.
Skipping Voice Guidance (for faster
operation)
Press and release the talk-button.
NOTE
  The Bluetooth ® Hands-Free system
is operable several seconds after the
ignition is switched to ACC or ON
(requires less than 15 seconds).
  When operating the audio unit or
the A/C while using Bluetooth ®
Hands-Free, the beep sounds or voice
guidance (audio unit)/cannot be
heard.
Tutorial
The tutorial explains how to use
Bluetooth
® Hands-Free.
To activate the tutorial, do the following:
1. Press the pick-up button or talk button
with a short press.
2. Say: [Beep] “Tutorial”
3. Follow the prompts to receive the
appropriate voice guidance instructions.
Commands useable anytime during
voice recognition
“Help” or “Go Back” are commands
which can be used at anytime during voice
recognition.
Help function use
The help function informs the user of all
the available voice commands under the
current conditions.
1. Say: [Beep] “Help”
2. Follow the prompts to receive the
appropriate voice guidance instructions.
Returning to previous operation
This command is for returning to the
previous operation while in the voice
recognition mode.
Say: [Beep] “Go Back”
To prevent a deterioration in the voice
recognition rate and voice quality, the
following points should be observed:
 




The voice recognition cannot be
performed while voice guidance or
the beep sound is operating. Wait
until the voice guidance or the beep
sound is fi nished before saying your
commands.
 


 Dialects or different wording other
than hands-free prompts cannot be
recognised by voice recognition. Speak
in the wording specifi ed by the voice
commands.
 


 It is not necessary to face the
microphone or approach it. Speak the
voice commands while maintaining a
safe driving position.
 


 Do not speak too slow or too loud.



 Speak clearly, without pausing between
words or numbers.
 


 Close the windows and/or the sunroof
to reduce loud noises from outside
the vehicle, or turn down the airfl ow
of the air-conditioning system while
Bluetooth
® Hands-Free is being used. 


 Make sure the vents are not directing air
up towards the microphone.
$9@&;&&%@&EJUJPOJOEC







5–111
Interior Features
Bluetooth®
Troubleshooting for Voice Recognition
If you do not understand an operation
method while in the voice recognition
mode, say “Tutorial” or “Help”.
Commands useable anytime during
voice recognition
“Go Back” and “Cancel” are commands
which can be used at anytime during voice
recognition.
Returning to previous operation
To return to the previous operation, say,
“Go Back” while in voice recognition
mode.
Cancel
To put the Bluetooth
® Hands-Free system
in standby mode, say, “Cancel” while in
voice recognition mode.
To prevent a deterioration in the voice
recognition rate and voice quality, the
following points should be observed:
 




The voice recognition cannot be
performed while voice guidance or
the beep sound is operating. Wait
until the voice guidance or the beep
sound is fi nished before saying your
commands.
 


 Phone related commands are available
only when your phone is connected via
Bluetooth
® . Make sure your phone is
connected via Bluetooth ® before you
operate phone related voice commands.
 


 Music play commands, such as Play
Artist and Play Album can be used only
in USB audio mode.
 


 Do not speak too slowly or loudly (no
loud voice).
 


 Speak clearly, without pausing between
words or numbers.
 


 Dialects or different wording other
than hands-free prompts cannot be
recognised by voice recognition. Speak
in the wording specifi ed by the voice
commands.
 


 It is not necessary to face the
microphone or approach it. Speak the
voice commands while maintaining a
safe driving position.
 


 Close the windows and/or the sunroof
to reduce loud noises from outside
the vehicle, or turn down the airfl ow
of the air-conditioning system while
Bluetooth
® Hands-Free is being used. 


 Make sure the vents are not directing air
up towards the microphone.
NOTE
If the voice recognition performance is
not satisfactory.
Refer to Troubleshooting on page 5-143 .
$9@&;&&%@&EJUJPOJOEC







*Some models.6–57
Maintenance and Care
Owner Maintenance
Fuse Panel Description
Fuse block (Engine compartment)
DESCRIPTION FUSE
RATING PROTECTED COMPONENT
1 C/U IG1 15 A For protection of various circuits
2 ENGINE IG1 7.5 A Engine control system
3 SUNROOF 10 A Sunroof
*
4 INTERIOR 15 A Overhead light
5
7.5 A Engine control system
6 AUDIO2 15 A Audio system
7 METER1 10 A Instrument cluster
8 SRS1 7.5 A Air bag
9 METER2 7.5 A Instrument cluster
*
10 RADIO 7.5 A Audio system
11 ENGINE3 15 A Engine control system
12 ENGINE1 15 A Engine control system
13 ENGINE2 15 A Engine control system
14 AUDIO1 25 A Audio system
15 A/C MAG 7.5 A Air conditioner
*
$9@&;&&%@&EJUJPOJOEC







6–61
Maintenance and Care
Appearance Care
Prevention
It is necessary to wash and wax your
vehicle to preserve its fi nish according to
the instructions in this section. These steps
should be taken immediately after you fi nd
water marks on your vehicle's fi nish.
Paint Chipping
Occurrence
Paint chipping occurs when gravel thrown
in the air by another vehicle's tyres hits
your vehicle.
How to avoid paint chipping
Keeping a safe distance between you and
the vehicle ahead reduces the chances
of having your paint chipped by fl ying
gravel.
NOTE
  The paint chipping zone varies
with the speed of the vehicle. For
example, when travelling at 90 km/h
(56 mph), the paint chipping zone is
50 m (164 ft).
  In low temperatures a vehicle's fi nish
hardens. This increases the chance of
paint chipping.
  Chipped paint can lead to rust
forming on your Mazda. Before this
happens, repair the damage by using
Mazda touch-up paint according
to the instructions in this section.
Failure to repair the affected area
could lead to serious rusting and
expensive repairs.
Follow all label and container directions
when using a chemical cleaner or polish.
Read all warnings and cautions.
Maintaining the Finish
Washing
CAUTION
  When the wiper lever is in the
position and the ignition is switched
ON, the wipers may move
automatically in the following cases:
 


 If the windscreen above the rain
sensor is touched or wiped with a
cloth.
 


 If the windscreen is struck with a
hand or other object from either
outside or inside the vehicle.
  Keep hands and scrapers clear of the
windscreen when the wiper lever is
in the
position and the ignition
is switched ON as fi ngers could be
pinched or the wipers and wiper
blades damaged when the wipers
activate automatically.
 If you are going to clean the
windscreen, be sure the wipers are
turned off completely (when it is
most likely that the engine is left
running) this is particularly important
when clearing ice and snow.
 
 Do not spray water in the engine
compartment. Otherwise, it could
result in engine-starting problems or
damage to electrical parts.
  When washing and waxing the
vehicle, be careful not to apply
excessive force to any single area
of the vehicle roof or the aerial.
Otherwise, you could dent the
vehicle or damage the aerial.
$9@&;&&%@&EJUJPOJOEC







8–21
Customer Information
Electromagnetic Compatibility
Aerial positions:
: front right of roof
: front left of roof
: centre of roof
: both sides of liftgate
Frequency Band (MHz) Maximum output power (Wattage) Aerial Positions
50 — 54 50
68 — 87.5 50
142 — 176 50
380 — 470 50
806 — 940 10
1200 — 1300 10
1710 — 1885 10
1885 — 2025 10
2400 — 2500 0.01 *1 In a cabin *1
*1 Only for Bluetooth ®
NOTE
After the installation of RF transmitters, check for disturbances from and to all electrical
equipment in the vehicle, both in the standby and transmit modes.
Check all electrical equipment:
 
 with the ignition ON 
 with the engine running 
 during a road test at various speeds.
$9@&;&&%@&EJUJPOJOEC