2015 MAZDA MODEL 6 headlights

Black plate (435,1)
WARNING
Do not replace the xenon fusion bulbs
yourself:
Replacing the xenon fusion bulbs
yourself is dangerous. Because the
xenon fusion bulbs require high
voltage, you could receive an electric
shock if the bulbs are handled
incorrectly. Consult an Authorized
Mazda Dealer when the replacement
is necessary.
Never touch the glass portion of a
halogen bulb with your bare hands and
always wear eye protection when
handling or working around the bulbs:
When a halogen bulb breaks, it is
dangerous. These bulbs contain
pressurized gas. If one is broken, it
will explode and serious injuries
could be caused by the flying glass.
If the glass portion is touched with
bare hands, body oil could cause the
bulb to overheat and explode when
lit.
Always keep halogen bulbs out of the
reach of children:
Playing with a halogen bulb is
dangerous. Serious injuries could be
caused by dropping a halogen bulb
or breaking it some other way.
NOTE
lTo replace the bulb, contact an Authorized
Mazda Dealer.
lIf the halogen bulb is accidentally touched,
it should be cleaned with rubbing alcohol
before being used.
lUse the protective cover and carton for the
replacement bulb to dispose of the old bulb
promptly and out of the reach of children.
qReplacing Exterior Light Bulbs
Headlights (With xenon fusion
headlights)
Low/High beam bulbs
You cannot replace the low/high beam
bulbs by yourself. The bulbs must be
replaced at an Authorized Mazda Dealer.
Headlights (With halogen headlights)
Low-beam bulbs
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. If you are changing the right bulb, start
the engine, turn the steering wheel all
the way to the left, and turn off engine.
If you are changing the left bulb, turn
the steering wheel to the right.
3. Pull the center of each plastic retainer
and remove the retainers.
Removal
Installation
Maintenance and Care
Owner Maintenance
6-41
Mazda6_8DQ8-EA-13L_Edition3 Page435
Friday, June 13 2014 6:23 PM
Form No.8DQ8-EA-13L

Black plate (438,1)
4. Remove the windshield washer fluid
reservoir and bolts.
Windshield washer
fluid reservoirBolt
Guide
5. Remove the guide.
Guide
6. Disconnect the connector from the unit
by pressing the tab on the connector
with your finger and pulling the
connector downward.
7. Turn the socket and bulb assembly to
remove it. Carefully remove the bulb
from its socket in the reflector by
gently pulling it straight backward out
of the socket.
8. Install the new bulb in the reverse order
of the removal procedure.
Daytime running lights/Parking lights
(With xenon fusion headlights)
Due to the complexity and difficulty of
the procedure, the LED bulbs must be
replaced by an Authorized Mazda Dealer.
NOTE
LED bulb replacement is not possible because
it is built into the unit. Replace the unit.
Front turn signal lights/Front side-
marker lights, Parking lights (With
halogen headlights)
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. If you are changing the right bulb, start
the engine, turn the steering wheel all
the way to the left, and turn off engine.
If you are changing the left bulb, turn
the steering wheel to the right.
6-44
Maintenance and Care
Owner Maintenance
Mazda6_8DQ8-EA-13L_Edition3 Page438
Friday, June 13 2014 6:23 PM
Form No.8DQ8-EA-13L

Black plate (439,1)
3. Pull the center of each plastic retainer
and remove the retainers.
Removal
Installation
4. Turn the screw counterclockwise and
remove it, and then partially peel back
the mudguard.
5. Turn the socket and bulb assembly
counterclockwise and remove it.
6. Disconnect the bulb from the socket.Front turn signal lights/Front side-
marker lights
Parking lights (With halogen
headlights)
7. Install the new bulb in the reverse order
of the removal procedure.
Fog lightsí
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. If you are changing the right bulb, start
the engine, turn the steering wheel all
the way to the left, and turn off engine.
If you are changing the left bulb, turn
the steering wheel to the right.
Maintenance and Care
Owner Maintenance
6-45íSome models. Mazda6_8DQ8-EA-13L_Edition3 Page439
Friday, June 13 2014 6:23 PM
Form No.8DQ8-EA-13L

Black plate (446,1)
3. Pull the fuse straight out with the fuse
puller provided on the fuse block
located in the engine compartment.
4. Inspect the fuse and replace it if it is
blown.
NormalBlown
5. Insert a new fuse of the same amperage
rating, and make sure it fits tightly. If it
does not fit tightly, have an expert
install it. We recommend an
Authorized Mazda Dealer.
If you have no spare fuses, borrow one
of the same rating from a circuit not
essential to vehicle operation, such as
the AUDIO or OUTLET circuit.
CAUTION
Always replace a fuse with a genuine
Mazda fuse or equivalent of the same
rating. Otherwise you may damage
the electric system.
6. Reinstall the cover and make sure that
it is securely installed.
Replacing the fuses under the hood
If the headlights or other electrical
components do not work and the fuses in
the cabin are normal, inspect the fuse
block under the hood. If a fuse is blown, it
must be replaced. Follow these steps:
1. Make sure the ignition is switched off,
and other switches are off.
2. Remove the fuse block cover.
6-52
Maintenance and Care
Owner Maintenance
Mazda6_8DQ8-EA-13L_Edition3 Page446
Friday, June 13 2014 6:23 PM
Form No.8DQ8-EA-13L

Black plate (450,1)
DESCRIPTIONFUSE
RATINGPROTECTED COMPONENT
53 HORN 15 A Horn
54 ROOM 15 A Overhead light
*1 With xenon fusion headlights
*2 With halogen headlights
Fuse block (Left side)
DESCRIPTIONFUSE
RATINGPROTECTED COMPONENT
1 P.SEAT D 30 A Power seat
í
2 P.WINDOW3 30 A Power windowsí
3 R.OUTLET3 15 A―
4 P.WINDOW2 25 A Power windows
5 SRS2/ESCL 15 A Seat weight sensor
í
6 D.LOCK 25 A Power door locks
7 SEAT WARM 20 A Seat warmerí
8 SUNROOF 10 A Moonroofí
9 F.OUTLET 15 A Accessory sockets
10 MIRROR 7.5 A Power control mirror
11 R.OUTLET1 15 A―
12―― ―
6-56
Maintenance and Care
íSome models.
Owner Maintenance
Mazda6_8DQ8-EA-13L_Edition3 Page450
Friday, June 13 2014 6:23 PM
Form No.8DQ8-EA-13L

Black plate (560,1)
qAir Conditioner
The type of refrigerant used is indicated on a label attached to the inside of the engine compartment. Check the
label before recharging the refrigerant. Refer to Climate Control System on page 5-2.
Item Classification
Refrigerant Type HFC134a (R-134a)
qLight Bulbs
Exterior light
Light bulbCategory
Wattage UNECE
*1(SAE)
HeadlightsHalogenHigh beam 65 HB3 (9005)
Low beam 55 H11 (H11)
Xenon fusion High/Low beam 35 D4S (D4S)
Daytime running lightsWith halogen bulb headlights 65 HB3 (9005)
With xenon fusion bulb headlights LED
*2―(―)
Front turn signal lights/Parking
lights (Front side-marker lights)With halogen bulb headlights 27/8―(#7444NA)
Front turn signal lights/
Front side-marker lightsWith xenon fusion bulb headlights 27/8―(#7444NA)
Parking lights With xenon fusion bulb headlights LED
*2―(―)
Fog lightsí55 H11 (H11)
Side turn signal lights LED*2―(―)
High-mount brake light LED*2―(―)
Rear turn signal lights 21 WY21W (7443NA)
Rear side-marker lights 5 W5W (―)
Brake lights/Taillights LED
*2―(―)
Taillights (Trunk lid side) 5 W5W (―)
Reverse lights 21 W21W (7440)
License plate lights 5 W5W (―)
*1 UNECE stands for United Nations Economic Commission for Europe.
*2 LED is the abbreviation for Light Emitting Diode.
Interior light
Light bulbCategory
Wattage UNECE
*1
Trunk light 3―
Overhead lights (Front)/Map lights 8―
Rear map lights 8―
Courtesy lights 5 W5W
Vanity mirror lights
í2―
*1 UNECE stands for United Nations Economic Commission for Europe.
9-6íSome models.
Specifications
Mazda6_8DQ8-EA-13L_Edition3 Page560
Friday, June 13 2014 6:23 PM
Form No.8DQ8-EA-13L

Black plate (565,1)
Item Feature Factory Setting Available Settings
Auto headlight
off
*2The time required for headlights to turn off after
ignition is switched off can be changed.
Refer to Setup on page 5-55.30 seconds120 seconds/
90 seconds/
60 seconds/
30 seconds/
0 seconds
*3
Auto-light controlThe headlight illumination on/off timing based on
surrounding lightness/darkness can be changed.
Refer to Setup on page 5-55.MediumLight/
Medium Light/
Medium/
Medium Dark/
Dark
High Beam
Control System
(HBC)The High Beam Control System (HBC) function can
be changed.
*4
Refer to Setup on page 5-55.OnOn/
Off
Turn indicatorThe turn indicator beep volume level can be changed.
Refer to Trip Computer and INFO Switch on page
4-18.HighHigh/
Low
Lights-on
reminder
*5
The volume of the lights-on reminder warning alarm
can be changed.
Refer to Trip Computer and INFO Switch on page
4-18.OFFHigh/
Low/
OFF
Blind Spot
Monitoring (BSM)
systemThe volume of the BSM warning beep can be
changed.
*6
Refer to Trip Computer and INFO Switch on page
4-18.HighHigh/
Low/
OFF
Lane Departure
Warning System
(LDWS)The warning sound for the Lane Departure
Warning System (LDWS) can be
changed.
*7
Refer to Trip Computer and INFO Switch
on page 4-18.U.S.A. Beep
Rumble/
Beep Except
U.S.A.Rumble
The volume of the warning
sound for the Lane Departure
Warning System (LDWS) can
be changed.
Refer to Trip Computer and
INFO Switch on page 4-18.RumbleU.S.A. High
High/
Medium/
Low Except
U.S.A.Low
BeepU.S.A. High
High/
Low Except
U.S.A.Low
The sensitivity of the warning for the Lane Departure
Warning System (LDWS) can be changed.
Refer to Trip Computer and INFO Switch on page
4-18.LowHigh/
Low
The warning timing in which the Lane Departure
Warning System (LDWS) determines that the vehicle
may be deviating from its lane can be changed.
Refer to Trip Computer and INFO Switch on page
4-18.Before lineBefore line/
At line
Personalization Features
9-11
Mazda6_8DQ8-EA-13L_Edition3 Page565
Friday, June 13 2014 6:23 PM
Form No.8DQ8-EA-13L

Black plate (566,1)
Item Feature Factory Setting Available Settings
Multi-information
display operation
soundThe operation sound volume for the following
operations can be changed.
lTrip computer data clearing
The INFO switch is pressed for 1.5 seconds or
longer while the average fuel economy or average
vehicle speed is displayed.
lNumerical value scroll
The Up/Down switch is pressed for 1.5 seconds or
longer, such as while the maintenance monitor
period setting screen is displayed.
Refer to Trip Computer and INFO Switch on page
4-18.HighHigh/
Low/
OFF
Meter displayThe distance unit can be changed.
Refer to Trip Computer and INFO Switch on page
4-18.miles or kmkm/
miles
The display language can be changed.
Refer to Trip Computer and INFO Switch on page
4-18.English, French,
or SpanishEnglish/
French/
Spanish
The temperature unit can be changed.
Refer to Trip Computer and INFO Switch on page
4-18.°F or °C°C/
°F
Forward
Obstruction
Warning (FOW)The system can be changed so that Forward
Obstruction Warning (FOW) does not operate.
*4
Refer to Trip Computer and INFO Switch on page
4-18.ONON/
OFF
The distance at which the collision warning activates
can be changed.
Refer to Trip Computer and INFO Switch on page
4-18.NearNear/
Far
The volume of the collision warning can be changed.
Refer to Trip Computer and INFO Switch on page
4-18.HighHigh/
Low/
OFF
Smart City Brake
Support (SCBS)The system can be changed so that Smart City Brake
Support (SCBS) does not operate.
*4
Refer to Trip Computer and INFO Switch on page
4-18.ONON/
OFF
*1 If the auto-wiper control is set to Off, the wiper lever
position is set to intermittent operation.
*2 If the setting is changed to 0 seconds, the following operation is performed according to the headlight switch
position:
lAtposition: Headlights turn off immediately after the ignition is switched off.lAt any position other than: Headlights do not turn off after the ignition is switched off.
*3 When set to 0 seconds, the lights-on reminder is operable.
*4 Though these systems can be turned OFF, doing so will defeat the purpose of the system and Mazda
recommends that these systems remain ON.
*5 The setting of the lights-on reminder can be changed with the time setting of auto headlight off function set to
0 seconds. Refer to Lights-On Reminder on page 7-38.
*6 Only the volume of the warning beep during Blind Spot Monitoring (BSM) operation can be changed. The
volume of the warning beep during Rear Cross Traffic Alert (RCTA) operation cannot be changed.
*7 For vehicles with an audio system other than the on-screen function type, the warning sound cannot be
changed. The warning sound is only a beep.
9-12
Personalization Features
Mazda6_8DQ8-EA-13L_Edition3 Page566
Friday, June 13 2014 6:23 PM
Form No.8DQ8-EA-13L