2015 MAZDA MODEL 3 HATCHBACK ECO mode

*Some models.4–66
When Driving
Switches and Controls
NOTE

 The headlights, other exterior lights and instrument panel illumination may not turn
off immediately even if the surrounding area becomes well-lit because the light sensor
determines that it is night time if the surrounding area is continuously dark for several
minutes such as inside long tunnels, traffi c jams inside tunnels, or in indoor parking
lots.
 In this case, the lights turn off if the light switch is turned to the position.
  When the headlight switch is in the position and the ignition is switched to ACC
or the ignition is switched off, the headlights, other exterior lights and instrument panel
illumination will turn off.
  The instrument panel illumination can be adjusted by rotating the knob in the
instrument cluster. Also, the antidazzle mode can be changed by rotating the knob until
a beep sound is heard. To adjust the brightness of the instrument panel illumination:
Refer to Instrument panel Illumination on page 4-28 .

 The sensitivity of the AUTO lights may be changed by an Authorised Mazda Repairer.
Refer to Personalisation Features on page 9-16 .
Xenon fusion headlight bulbs
*
The low-beam bulbs of the headlights have xenon fusion bulbs that produce a bright white
beam over a wide area.
WARNING
Do not replace the xenon fusion bulbs yourself
Replacing the xenon fusion bulbs yourself is dangerous. Because the xenon fusion
bulbs require high voltage, you could receive an electric shock if the bulbs are handled
incorrectly. Consult an expert repairer, we recommend an Authorised Mazda Repairer
when the replacement is necessary.
NOTE
If the headlights fl icker, or the brightness weakens, the bulb-life may be depleted and a
replacement is necessary. Consult an expert repairer, we recommend an Authorised Mazda
Repairer.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.4–68
When Driving
Switches and Controls
Coming Home Light System *
The coming home light system turns on
the headlights (low beams) when the lever
is operated.
When the lever is pulled with the ignition
switched to ACC or OFF, the low beam
headlights turn on.
The headlights turn off after a certain
period of time has elapsed after the doors
are closed.
NOTE
  The time until the headlights turn off
after the all of the doors are closed
can be changed.
 Refer to Personalisation Features on
page 9-16 .
  If no operations are done for 3
minutes after the lever is pulled, the
headlights turn off.
  The headlights turn off if the lever is
pulled again while the headlights are
illuminated.
Leaving Home Light System *
The leaving home light system turns on
the lights when the key unlock switch is
pressed while away from the vehicle.
When the ignition switch and the
headlight switch are as indicated below,
the headlights will illuminate when the
transmitter unlock button is pressed and
the vehicle receives the transmitter signal.
The headlights turn off after a certain
period of time has elapsed (30 seconds).
 


 Ignition switch: off



 Headlight switch: or
The following lights turn on when the
leaving home light system is operated.
Low beams, Position lights, Tail lights,
Number plate lights
Unlock button
Lock button
NOTE
  Operation of the leaving home light
system can be turned on or off.
 Refer to Personalisation Features on
page 9-16 .
  When the transmitter lock button is
pressed and the vehicle receives the
transmitter signal, the headlights turn
off.
  When the headlight switch is in a
position other than
or , the
headlights turn off.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.4–77
When Driving
Switches and Controls
Windscreen Washer
Pull the lever toward you and hold it to
spray washer fl uid.
Washer OFF
NOTE
With the wiper lever in the or
intermittent position/
position, the
wipers will operate continuously until
the lever is released.
If the washer does not work, inspect the
fl uid level (page 6-34 ). If the fl uid level
is normal, consult an expert repairer,
we recommend an Authorised Mazda
Repairer.
NOTE
(With headlight washers)
When the headlights are on, the
headlight washers operate automatically
once every fi fth time the windscreen
washer operates.
Refer to Headlight Washer on page 4-78 .
Rear Window Wiper and
Washer
*
The ignition must be switched ON to use
the wiper.
Rear Window Wiper
Turn the wiper on by turning the rear
wiper/washer switch.
Switch Position
Wiper operation
No. Type A Type B
Intermittent
Normal
Rear Window Washer
To spray washer fl uid, turn the rear wiper/
washer switch to the
position. After the
switch is released, the washer will stop.
If the washer does not work, inspect the
fl uid level (page 6-34 ). If the fl uid level is
normal and the washer still does not work,
consult an expert repairer, we recommend
an Authorised Mazda Repairer.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.4–88
When Driving
ABS/TCS/DSC
Traction Control System
(TCS)
*
The Traction Control System (TCS)
enhances traction and safety by controlling
engine torque and braking. When the TCS
detects driving wheel slippage, it lowers
engine torque and operates the brakes to
prevent loss of traction.
This means that on a slick surface, the
engine adjusts automatically to provide
optimum power to the drive wheels,
limiting wheel spin and loss of traction.
The warning light turns on when the
system has a malfunction.
Refer to Warning Lights on page 4-41 .
WARNING
Do not rely on the Traction Control
System (TCS) as a substitute for safe
driving:
The Traction Control System (TCS)
cannot compensate for unsafe and
reckless driving, excessive speed,
tailgating (following another vehicle
too closely), and hydroplaning (reduced
tyre friction and road contact because
of water on the road surface). You can
still have an accident.
Use snow tyres or tyre chains and
drive at reduced speeds when roads are
covered with ice and/or snow:
Driving without proper traction devices
on snow and/or ice-covered roads
is dangerous. The Traction Control
System (TCS) alone cannot provide
adequate traction and you could still
have an accident.
NOTE
To turn off the TCS, press the DSC OFF
switch (page 4-90 ).
TCS/DSC Indicator Light
This indicator light stays on for a few
seconds when the ignition is switched
ON. If the TCS or DSC is operating, the
indicator light fl ashes.
If the light stays on, the TCS, DSC
or the brake assist system may have a
malfunction and they may not operate
correctly. Take your vehicle to an expert
repairer, we recommend an Authorised
Mazda Repairer.
NOTE
  In addition to the indicator light
fl ashing, a slight labouring sound
will come from the engine. This
indicates that the TCS/DSC is
operating properly.
  On slippery surfaces, such as fresh
snow, it will be impossible to achieve
high rpm when the TCS is on.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.4–89
When Driving
ABS/TCS/DSC
Dynamic Stability
Control (DSC)
*
The Dynamic Stability Control (DSC)
automatically controls braking and engine
torque in conjunction with systems such
as ABS and TCS to help control side slip
when driving on slippery surfaces, or
during sudden or evasive manoeuvring,
enhancing vehicle safety.
Refer to ABS (page 4-87 ) and TCS (page
4-88 ).
DSC operation is possible at speeds
greater than 20 km/h (12 mph).
The warning light turns on when the
system has a malfunction.
Refer to Warning Lights on page 4-41 .
WARNING
Do not rely on the Dynamic Stability
Control as a substitute for safe driving:
The Dynamic Stability Control (DSC)
cannot compensate for unsafe and
reckless driving, excessive speed,
tailgating (following another vehicle
too closely), and hydroplaning (reduced
tyre friction and road contact because
of water on the road surface). You can
still have an accident.
CAUTION
  The DSC may not operate correctly
unless the following are observed:
 


 Use tyres of the correct size
specifi ed for your Mazda on all
four wheels.
 


 Use tyres of the same
manufacturer, brand and tread
pattern on all four wheels.
 


 Do not mix worn tyres. 

 The DSC may not operate correctly
when tyre chains are used or a
temporary spare tyre is installed
because the tyre diameter changes.
TCS/DSC Indicator Light
This indicator light stays on for a few
seconds when the ignition is switched
ON. If the TCS or DSC is operating, the
indicator light fl ashes.
If the light stays on, the TCS, DSC
or the brake assist system may have a
malfunction and they may not operate
correctly. Take your vehicle to an expert
repairer, we recommend an Authorised
Mazda Repairer.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.4–94
When Driving
Fuel Economy Monitor
Fuel Economy Monitor *
For vehicles with type C/type D audio, the Control Status, Fuel Consumption, and
Effectiveness are switched and displayed by operating each icon in the display.
In addition, after completing a trip, the total energy effi ciency to date is displayed in the
ending display when the ending display is turned on.
1. Select the
icon on the home screen to display the applications screen.
2. Select the “Fuel Economy Monitor”.
3. Operate the commander switch or touch the screen and display the menu.
NOTE
When the menu is displayed by touching the screen, the display is hidden automatically
after 6 seconds.
4. Select the icon in the menu and perform the operation. Each icon operates as follows:
Indication on display Control status
Hides the menu display.
Displays the application screen.
Switches the Fuel Economy Monitor in the order of
Control Status, Fuel Consumption, and
Effectiveness.
Resets the fuel economy data.
Displays the following setting screen. Ending display on/off switching On/off switching for function which synchronizes
reset fuel economy data to trip meter (Trip A)
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.4–10 0
When Driving
i-ACTIVSENSE
i-ACTIVSENSE *
i-ACTIVSENSE is a collective term covering a series of advanced safety and driver support
systems which make use of a Forward Sensing Camera (FSC) and radar sensors. These
systems consist of active safety and pre-crash safety systems.
These systems are designed to assist the driver in safer driving by reducing the load on the
driver and helping to avert collisions or reduce their severity. However, because each system
has its limitations, always drive carefully and do not rely solely on the systems.
Active Safety Technology
Active Safety Technology supports safer driving by helping the driver to recognise potential
hazards and avert accidents.
Driver awareness support systems
Nighttime visibility
Adaptive Front Lighting System (AFS) ............................................................................ 4-103
High Beam Control System (HBC) .................................................................................. 4-104
Forward/rear detection
Lane Departure Warning System (LDWS) ....................................................................... 4-107
Rear Vehicle Monitoring (RVM) system .......................................................................... 4-114
Inter-vehicle distance recognition
Distance Recognition Support System (DRSS) ................................................................ 4-120
Driver Support System
Inter-vehicle distance
Mazda Radar Cruise Control (MRCC) ............................................................................. 4-123
Speed control
Adjustable Speed Limiter ................................................................................................. 4-133
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.4–103
When Driving
i-ACTIVSENSE
Adaptive Front Lighting
System (AFS)
*
The adaptive front lighting system (AFS)
automatically adjusts the headlight beams
to the left or right in conjunction with the
operation of the steering wheel after the
headlights have been turned on.
AFS OFF Indicator Light
When illuminated
This indicator light illuminates briefl y
when the ignition is switched ON, and
then turns off. Pressing the AFS OFF
switch cancels the AFS function and
illuminates the indicator light.
When fl ashing
The indicator light fl ashes continuously
if the system is malfunctioning. Consult
an expert repairer, we recommend an
Authorised Mazda Repairer.
NOTE
  Even if the AFS is not operating due
to some malfunction, the normal
headlight function is still operable.
  If there is a malfunction with the
headlight auto-levelling function, the
indicator light fl ashes.
AFS OFF switch
Pressing the AFS OFF switch turns off the
AFS. The AFS OFF indicator light in the
instrument cluster illuminates.
Pressing the AFS OFF switch again turns
off the switch illumination and turns on
the AFS operation. The AFS OFF indicator
light turns off.
.B[EB@&'&&"@&EJUJPOJOEC