2015 MAZDA MODEL 3 HATCHBACK ECU

4–9
When Driving
Start/Stop Engine
NOTE
 (Germany) Drive immediately after starting the
engine. However do not use high
engine speeds until reaching the
operating temperature.
 
(SKYACTIV-G 1.5, MZR 1.6,
SKYACTIV-G 2.0)
 


 Whether the engine is cold or
warm, it should be started without
the use of the accelerator.
 


 If the engine does not start the fi rst
time, refer to Starting a Flooded
Engine under Emergency Starting.
If the engine still does not start,
have your vehicle inspected by an
Authorised Mazda Repairer (page
7-24 ).
 
(SKYACTIV-D 2.2) If the ambient temperature is lower
than about - 10 °C (14 °F), the
maximum engine speed may not
be attained for about three minutes
after the engine starts to protect the
engine.
 (Manual transaxle vehicle with
i-stop function)
 If the engine has stopped due to
stalling, it can be restarted by
depressing the clutch pedal within 3
seconds of the engine stopping.
 The engine cannot be restarted even
if the clutch pedal is depressed under
the following conditions:
 


 The driver's door is open. 


 The driver's seat belt is unfastened. 


 The clutch pedal is not released
completely after the engine stalled.
 

 The clutch pedal is depressed with
the engine not stopped completely.
Engine Start Function When Key
Battery is Dead
CAUTION
When starting the engine by holding
the transmitter over the push button
start due to a dead key battery or a
malfunctioning key, be careful not
to allow the following, otherwise the
signal from the key will not be received
correctly and the engine may not start.
 
 Metal parts of other keys or metal
objects touch the key.

  Spare keys or keys for other vehicles
equipped with an immobilizer system
touch or come near the key.

  Devices for electronic purchases, or
security passage touch or come near
the key.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.4–44
When Driving
Instrument Cluster and Display
Signal Indicator Lights Page
(Green) * i-stop Indicator Light 4-22
* i-ELOOP Indicator Light 4-93
(Blue) Low Engine Coolant Temperature Indicator Light 4-46
* Shift Position Indication 4-51
Headlight High-Beam Indicator Light 4-67 ,
4-67
Direction Indicator/Hazard Warning Indicator Lights 4-72 ,
4-80
Security Indicator Light *1 3-45
(Green)
* Mazda Radar Cruise Control (MRCC) Indicator Light 4-127
(Amber)
* Cruise Main Indicator Light 4-157
(Green)
* Cruise Set Indicator Light 4-157
(Amber)
* Adjustable Speed Limiter Main Indicator Light 4-135
(Green)
* Adjustable Speed Limiter Set Indicator Light 4-135
Lights-On Indicator Light 4-62
* Front Fog Light Indicator Light 4-70
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.5–19
Interior Features
Audio System
Aerial
Aerial (Saloon)
The aerial is embedded into the window
glass.
CAUTION
When washing the inside of the window
which has an aerial, use a soft cloth
dampened in lukewarm water, gently
wiping the aerial lines.
Use of glass cleaning products could
damage the aerial.
Aerial (Hatchback)
Type A
To remove the aerial, turn it anticlockwise.
To install the aerial, turn it clockwise.
Make sure the aerial is securely installed.
RemoveInstall
CAUTION
  To prevent damage to the aerial,
remove it before entering a car wash
facility or passing beneath a low
overhead clearance.
  Be careful around the aerial when
removing snow from the roof.
Otherwise the aerial could be
damaged.
NOTE
When leaving your vehicle unattended,
we recommend that you remove the
aerial and store it inside the vehicle.
Type B
Aerial
Type C *
The aerial is embedded into the window
glass.
.B[EB@&'&&"@&EJUJPOJOEC







5–78
Interior Features
Audio System
Type C/Type D (Without DVD/CD
player)
Auxiliary jack
USB port
Type C/Type D (With DVD/CD player)
USB port Auxiliary jack
Connecting a device
1. Open the console lid (With DVD/CD
player).
2. If there is a cover on the AUX jack or
USB port, remove the cover.
3. Connect the connector on the device to
the USB port.
Connecting with a connector lead
1. Open the console lid (With DVD/CD
player).
2. If there is a cover on the AUX jack or
USB port, remove the cover.
3. Connect the device plug/connector lead
to the auxiliary jack/USB port. For
vehicles with a DVD/CD player, pass
the device plug/connector lead through
the notch in the console and connect.
WARNING
Do not allow the connection plug cord
to get tangled with the parking brake or
the shift lever:
Allowing the plug cord to become
tangled with the parking brake or the
shift lever is dangerous as it could
interfere with driving, resulting in an
accident.
CAUTION
Do not place objects or apply force to
the auxiliary jack/USB port with the
plug connected.
NOTE
  Insert the plug into the auxiliary jack/
USB port securely.
  Insert or pull out the plug with the
plug perpendicular to the auxiliary
jack/USB port hole.
  Insert or remove the plug by holding
its base.
.B[EB@&'&&"@&EJUJPOJOEC







5–10 0
Interior Features
Bluetooth®
Registered device read-out
Bluetooth
® Hands-Free can read-out the
devices registered to its system.
NOTE
Do this function only when parked. It is
too distracting to attempt while driving
and you may make too many errors to
be effective.
1. Press the pick-up button or talk button
with a short press.
2. Say: [Beep] “Setup”
3. Prompt: “Select one of the following:
Pairing options, confi rmation prompts,
language, password, select phone or
select music player.”
4. Say: [Beep] “Pairing options”
5. Prompt: “Select one of the following:
Pair, edit, delete, list, or set pin code.”
6. Say: [Beep] “List” 7. Prompt: “XXXXX..., XXXXX...,
XXXXX... (Ex. Device A, device B,
device C)” (The voice guidance reads
out the device tags registered to the
hands-free system.)
Press the talk button with a short press
during the read-out at the desired
device, and then say one of the
following voice commands to execute
it.
 

 
 “Select phone”: Selects device (Mobile
phone) when the talk button is short-
pressed.
 

 
 “Select music player”: Selects device
(Music player) when the talk button is
short-pressed.
 

 
 “Edit”: Edits device when the talk
button is short-pressed.
 

 
 “Continue”: Continues the list read-
out.
 

 
 “Delete”: Deletes the registered device
when the talk button is short-pressed.
 

 
 “Previous”: Returns to the previous
device in read-out when the talk button
is short-pressed.
8. Prompt: “End of list, would you like to
start from the beginning?”
9. Say: [Beep] “No”
10. Prompt: “Returning to main menu.”
Device selection
If several devices have been paired, the
Bluetooth
® unit links the device last
paired. If you would like to link a different
paired device, it is necessary to change the
link. The order of device priority after the
link has been changed is maintained even
when the ignition is switched off.
.B[EB@&'&&"@&EJUJPOJOEC







5–110
Interior Features
Bluetooth®
Commands useable anytime during
voice recognition
“Help” or “Go Back” are commands
which can be used at anytime during voice
recognition.
Help function use
The help function informs the user of all
the available voice commands under the
current conditions.
1. Say: [Beep] “Help”
2. Follow the prompts to receive the
appropriate voice guidance instructions.
Returning to previous operation
This command is for returning to the
previous operation while in the voice
recognition mode.
Say: [Beep] “Go Back”
To prevent a deterioration in the voice
recognition rate and voice quality, the
following points should be observed:
 




The voice recognition cannot be
performed while voice guidance or
the beep sound is operating. Wait
until the voice guidance or the beep
sound is fi nished before saying your
commands.
 


 Dialects or different wording other
than hands-free prompts cannot be
recognised by voice recognition. Speak
in the wording specifi ed by the voice
commands.
 


 It is not necessary to face the
microphone or approach it. Speak the
voice commands while maintaining a
safe driving position.
 


 Do not speak too slow or too loud.



 Speak clearly, without pausing between
words or numbers.
 


 Close the windows and/or the sunroof
to reduce loud noises from outside
the vehicle, or turn down the airfl ow
of the air-conditioning system while
Bluetooth
® Hands-Free is being used. 


 Make sure the vents are not directing air
up towards the microphone.
NOTE
If the voice recognition performance is
not satisfactory.
Refer to Voice Recognition Learning
Function (Speaker Enrolment) (Type A/
Type B) on page 5-112 .
Refer to Troubleshooting on page 5-149 .
Security Setting (Type A/Type B)
If a password is set, the system cannot be
activated unless the password is input.
NOTE
Do this function only when parked. It is
too distracting to attempt while driving
and you may make too many errors to
be effective.
Password setting
1. Press the pick-up button or talk button
with a short press.
2. Say: [Beep] “Setup”
3. Prompt: “Select one of the following:
Pairing options, confi rmation prompts,
language, password, select phone or
select music player.”
4. Say: [Beep] “Password”
5. Prompt: “Password is disabled. Would
you like to enable it?”
6. Say: [Beep] “Yes”
7. Prompt: “Please say a 4-digit
.B[EB@&'&&"@&EJUJPOJOEC







5–111
Interior Features
Bluetooth®
password. Remember this password. It
will be required to use this system.”
8. Say: [Beep] “XXXX” (Say a desired
4-digit password, “PCode”.)
9. Prompt: “Password XXXX (Password,
PCode). Is this correct?”
10. Say: [Beep] “Yes”
11. Prompt: “Password is enabled.”
Using Bluetooth
® Hands-Free with a
password
1. Press the pick-up button or talk button
with a short press.
2. Prompt: “Hands-Free system
is locked. State the password to
continue.”
3. Say: [Beep] “XXXX” (Say the set
password “PCode”.)
4. If the correct password is input, voice
guidance “XXXXXX... (Ex. “Mary's
device”) (Device tag) is connected” is
announced.
If the password is incorrect, voice
guidance “XXXX (4-digit password,
Pcode) incorrect password, please try
again” is announced.
Cancelling the password
NOTE
Do this function only when parked. It is
too distracting to attempt while driving
and you may make too many errors to
be effective.
1. Press the pick-up button or talk button
with a short press.
2. Say: [Beep] “Setup”
3. Prompt: “Select one of the following:
Pairing options, confi rmation prompts,
language, password, select phone or
select music player.”
4. Say: [Beep] “Password”
5. Prompt: “Password is enabled. Would
you like to disable it?”
6. Say: [Beep] “Yes”
7. Prompt: “Password is disabled.”
Confi rmation Prompts
The confi rmation prompt confi rms the
command content to the user before
advancing to the operation requested by
the user. When this function is turned
on, the system reads out the voice
input command previously received
and confi rms whether the command is
correct before advancing to the command
execution.
When the confi rmation prompt function is
turned on:
(Ex. “Calling John's device. Is this
correct?”)
When the confi rmation prompt function is
turned off:
(Ex. “Calling John's device.”)
NOTE
If the confi rmation prompt function is
turned off when making an emergency
call, the system reads out and confi rms
the command before executing it.
1. Press the pick-up button or talk button
with a short press.
2. Say: [Beep] “Setup”
3. Prompt: “Select one of the following:
Pairing options, confi rmation prompts,
language, password, select phone or
select music player.”
4. Say: [Beep] “Confi rmation prompts”
.B[EB@&'&&"@&EJUJPOJOEC







5–122
Interior Features
Bluetooth®
7. Prompt: “Deleting XXXXX... (Ex.
“John's phone”) (Registered voice tag)
Home (Registered location). Is this
correct?”
8. Say: [Beep] “Yes”
9. Prompt: “XXXXX... (Ex. “John's
phone”) (Registered voice tag) Home
(Registered location) deleted.”
(Complete deletion of the phonebook
data)
All data registered to the Bluetooth
®
Hands-Free phonebook can be erased.
NOTE
Do this function only when parked. It is
too distracting to attempt while driving
and you may make too many errors to
be effective.
1. Press the pick-up button or talk button
with a short press.
2. Say: [Beep] “Phonebook”
3. Prompt: “Select one of the following:
New entry, edit, list names, delete,
erase all or import contact.”
4. Say: [Beep] “Erase all”
5. Prompt: “Are you sure you want to
delete everything from your Hands
Free system phonebook?”
6. Say: [Beep] “Yes”
7. Prompt: “You are about to delete
everything from your Hands Free
system phonebook. Do you want to
continue?”
8. Say: [Beep] “Yes”
9. Prompt: “Please wait, deleting the
Hands Free system phonebook.”
10. Prompt: “Hands-Free system
phonebook deleted.” Read-out of names registered to the
Bluetooth
® Hands-Free phonebook
Bluetooth
® Hands-Free can read out the
list of names registered to its phonebook.
1. Press the pick-up button or talk button
with a short press.
2. Say: [Beep] “Phonebook”
3. Prompt: “Select one of the following:
New entry, edit, list names, delete,
erase all or import contact.”
4. Say: [Beep] “List names”
5. Prompt: “XXXXX..., XXXXX...,
XXXXX... (Ex. “John's phone”, Mary's
phone, Bill's phone)” (Voice guidance
reads out the voice tags registered to
the phonebook.)
Press the talk button with a short press
during the read-out at the desired name,
and then say one of the following voice
commands to execute it.
 

 
 “Continue”: Continues the list readout.


 
 “Call”: Calls the registered phonebook
data when the talk button is short-
pressed.
 

 
 “Edit”: Edits the registered phonebook
data when the talk button is short-
pressed.
 

 
 “Delete”: Deletes the registered
phonebook data when the talk button is
short-pressed.
 

 
 “Previous”: Returns to the previous
phonebook data in read-out when the
talk button is short-pressed.
6. Prompt: “End of list, would you like to
start from the beginning?”
7. Say: [Beep] “No”
.B[EB@&'&&"@&EJUJPOJOEC