2015 MAZDA MODEL 3 HATCHBACK ECU

6–60
Maintenance and Care
Owner Maintenance
6. Disconnect the bulb from the socket.
Rear direction indicator lights
Brake lights/Tail lights (Bulb type)
7. Install the new bulb.
8. Insert the wing bolt into the jack with
the jack screw pointing to the down
and turn the wing bolt clockwise to
temporarily tighten it.9. Turn the jack screw in the direction
shown in the fi gure.
10. Turn the wing bolt completely to secure
the jack.
NOTE
If the jack is not completely secured, it
could rattle while driving. Make sure the
jack screw is suffi ciently tightened.
11. Install the cover in the reverse order of
the removal procedure.
12. Insert the cover tabs and install the
cover.
Tabs
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.6–61
Maintenance and Care
Owner Maintenance
NOTE
Verify that the cover is securely
installed.
Reverse lights(Saloon), Reverse lights/
Rear fog light (Hatchback)
*
Saloon
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Pull the centre of each plastic retainer
and remove the retainers.
3. Peel back the boot lid trim.
Removal
Installation
4. Disconnect the electrical connector
from the bulb by pressing the tab on the
connector with your fi nger and pulling
the connector.
5. Turn the socket and bulb assembly
anticlockwise and remove it.
6. Disconnect the bulb from the socket.
7. Install the new bulb in the reverse order
of the removal procedure.
.B[EB@&'&&"@&EJUJPOJOEC







6–66
Maintenance and Care
Owner Maintenance
3. Pull the fuse straight out with the
fuse puller provided on the fuse block
located in the engine compartment.
4. Inspect the fuse and replace it if it is
blown.
NormalBlown
5. Insert a new fuse of the same amperage
rating, and make sure it fi ts tightly. If
it does not fi t tightly, have an expert
install it. We recommend an Authorised
Mazda Repairer.
If you have no spare fuses, borrow one
of the same rating from a circuit not
essential to vehicle operation, such as
the AUDIO or OUTLET circuit.
CAUTION
Always replace a fuse with a genuine
Mazda fuse or equivalent of the same
rating. Otherwise you may damage the
electric system.
6. Reinstall the cover and make sure that
it is securely installed.
Replacing the fuses under the bonnet
If the headlights or other electrical
components do not work and the fuses
in the cabin are normal, inspect the fuse
block under the bonnet. If a fuse is blown,
it must be replaced. Follow these steps:
1. Make sure the ignition is switched off,
and other switches are off.
2. Remove the fuse block cover.
.B[EB@&'&&"@&EJUJPOJOEC







6–67
Maintenance and Care
Owner Maintenance
3. If any fuse but the MAIN fuse is
blown, replace it with a new oneof the
same amperage rating .
Normal
Blown
WARNING
Do not replace the main fuse and
multiplex slow blow fuse by yourself.
Have an Authorised Mazda Repairer
perform the replacement:
Replacing these fuses by yourself
is dangerous because they are high
current fuses. Incorrect replacement
could cause an electrical shock or a
short circuit resulting in a fi re.
4. Reinstall the cover and make sure that
it is securely installed.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.7–2
If Trouble Arises
Parking in an Emergency
Parking in an Emergency
The hazard warning lights should always
be used when you stop on or near a
roadway in an emergency.
The hazard warning lights warn other
drivers that your vehicle is a traffi c hazard
and that they must take extreme caution
when near it.

Depress the hazard warning fl asher and
all the direction indicators will fl ash. The
hazard warning indicator lights in the
instrument cluster fl ash simultaneously.
NOTE

 The direction indicators do not work
when the hazard warning lights are
on.
  Check local regulations about the use
of hazard warning lights while the
vehicle is being towed to verify that
it is not in violation of the law.
Roadside Emergency
Triangle Retaining Strap
*
Keep the roadside emergency triangle in
the right side trim and secure it with the
strap.
Saloon
Strap
Hatchback
Strap
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.7–5
If Trouble Arises
Flat Tyre
Jack *
NOTE
Your vehicle may or may not be
equipped with a jack and wheel brace.
For details, consult an Authorised
Mazda Dealer.
To remove the jack
1 . (Saloon)
Push the tabs and remove the cover.
Tabs
(Hatchback)
Turn the knob and remove the cover.
2. Turn the wing bolt and jack screw
anticlockwise.
To secure the jack
1. Insert the wing bolt into the jack with
the jack screw pointing to the down
and turn the wing bolt clockwise to
temporarily tighten it.
2. Turn the jack screw in the direction
shown in the fi gure.
3. Turn the wing bolt completely to secure
the jack.
NOTE
If the jack is not completely secured, it
could rattle while driving. Make sure the
jack screw is suffi ciently tightened.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.7–6
If Trouble Arises
Flat Tyre
4. Insert the cover tabs and install the
cover.
(Saloon)
Tabs
Tabs (Hatchback)
NOTE
Verify that the cover is securely
installed.
Maintenance
 




 Always keep the jack clean.



 Make sure the moving parts are kept
free from dirt or rust.
 


 Make sure the screw thread is
adequately lubricated.
Spare Tyre *
Your Mazda has a temporary spare tyre.
The temporary spare tyre is lighter and
smaller than a conventional tyre, and is
designed only for emergency use and
should be used only for VERY short
periods. Temporary spare tyres should
NEVER be used for long drives or
extended periods.
WARNING
Do not install the temporary spare tyre
on the front wheels (driving wheels):
Driving with the temporary spare tyre
on one of the front driving wheels is
dangerous. Handling will be affected.
You could lose control of the vehicle,
especially on ice or snow bound roads,
and have an accident. Move a regular
tyre to the front wheel and install the
temporary spare tyre to the rear.
.B[EB@&'&&"@&EJUJPOJOEC







7–7
If Trouble Arises
Flat Tyre
CAUTION
  When using the temporary spare
tyre, driving stability may decrease
compared to when using only the
conventional tyre. Drive carefully.
  To avoid damage to the temporary
spare tyre or to the vehicle, observe
the following precautions:
 


 Do not exceed 80 km/h (50 mph).



 Avoid driving over obstacles. Also,
do not drive through an automatic
car wash. This tyre's diameter is
smaller than a conventional tyre,
so the ground clearance is reduced
about 10 mm (0.4 in).
 


 Do not use a tyre chain on this tyre
because it will not fi t properly.




 Do not use your temporary spare
tyre on any other vehicle, it has
been designed only for your
Mazda.
 


 Use only one temporary spare tyre
on your vehicle at the same time.
To remove the spare tyre
1. Lift the boot/luggage compartment mat.
Boot/Luggage compartment mat
2. Turn the spare tyre hold-down bolt
anticlockwise.
Spare tyre hold-down bolt
To secure the spare tyre
Store the spare tyre in the reverse order
of removal. After storing, verify that the
spare tyre is stored securely.
.B[EB@&'&&"@&EJUJPOJOEC