2015 MAZDA MODEL 3 HATCHBACK Owners Manual (in English)

*Some models.4–155
When Driving
i-ACTIVSENSE
Radar Sensors (Rear) *
The radar sensors (rear) for the rear vehicle monitoring system are equipped inside the rear
bumper, one each on the left and right sides.
Saloon
Radar sensors (rear)
Hatchback
Radar sensors (rear)
The surface area of the rear bumper near the radar sensors (rear) should always be clean so
that the rear vehicle monitoring system operates correctly. Do not apply stickers or similar
objects to the rear bumper.
Refer to Exterior Care on page 6-71 .
NOTE
Consult an Authorised Mazda Dealer for radar sensors (rear) repairs and replacement, or
repair, replacement or painting of the rear bumper near the radar sensors (rear).
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.4–156
When Driving
Cruise Control
Cruise Control *
With cruise control, you can set and automatically maintain any speed of more than about
25 km/h (16 mph).
WARNING
Do not use the cruise control under the following conditions:
Using the cruise control under the following conditions is dangerous and could result
in loss of vehicle control.
 
 Hilly terrain 
 Steep inclines 
 Heavy or unsteady traffi c 
 Slippery or winding roads 
 Similar restrictions that require inconsistent speed
Cruise Control Switch
OFF switch ON switch Without Adjustable Speed Limiter With Adjustable Speed LimiterON/OFF switch
CANCEL switch RESUME switch
SET+/SET- switch
CANCEL switch
RESUME switch
SET+/SET- switch
.B[EB@&'&&"@&EJUJPOJOEC







4–157
When Driving
Cruise Control
Cruise Main Indicator Light
(Amber)/Cruise Set Indicator
Light (Green)
The indicator light has two colours.
Cruise Main Indicator Light (Amber)
The indicator light illuminates amber
when the cruise control system is
activated.
Cruise Set Indicator Light (Green)
The indicator light illuminates green when
a cruising speed has been set.
Activation/Deactivation
With adjustable speed limiter
To activate the system, press the ON/OFF
switch. The cruise main indicator light
(amber) illuminates.
To deactivate the system, press the switch
again.
The cruise main indicator light (amber)
turns off.
Without adjustable speed limiter
To activate the system, press the ON
switch. The cruise main indicator light
(amber) illuminates.
To deactivate the system, press the OFF
switch.
The cruise main indicator light (amber)
turns off.
WARNING
Always turn off the cruise control
system when it is not in use:
Leaving the cruise control system in an
activation-ready state while the cruise
control is not in use is dangerous as
the cruise control could unexpectedly
activate if the activation button is
accidentally pressed, and result in loss
of vehicle control and an accident.
NOTE
When the ignition is switched OFF, the
system status before it was turned off is
maintained. For example, if the ignition
is switched OFF with the cruise control
system operable, the system will be
operable when the ignition is switched
ON the next time.
To Set Speed
1 . (With adjustable speed limiter)
Activate the cruise control system
by pressing the ON/OFF switch. The
cruise main indicator light (Amber)
illuminates.
(Without adjustable speed limiter)
Activate the cruise control system
by pressing the ON switch. The
cruise main indicator light (Amber)
illuminates.
2. Accelerate to the desired speed, which
must be more than 25 km/h (16 mph).
.B[EB@&'&&"@&EJUJPOJOEC







4–158
When Driving
Cruise Control
3. Set the cruise control by pressing the
SET
or SET switch at the desired
speed. The cruise control is set at the
moment the SET
or SET switch is
pressed. Release the accelerator pedal
simultaneously. The cruise set indicator
light (Green) illuminates.
NOTE
  The cruise control speed setting
cannot be performed under the
following conditions:
 


(Automatic transaxle)
 The selector lever is in the P or N
position.
 


(Manual transaxle)
 The shift lever is in the neutral
position.
 


 The parking brake is applied.



(Vehicles with adjustable speed
limiter)
  The ON/OFF switch for the
adjustable speed limiter is pressed.


 Release the SET or SET switch
at the desired speed, otherwise the
speed will continue increasing while
the SET
switch is pressed and
held, and continue decreasing while
the SET
switch is pressed and held
(except when the accelerator pedal is
depressed).
  On a steep grade, the vehicle may
momentarily slow down while
ascending, or speed up while
descending.
NOTE
  Cruise control will cancel if the
vehicle speed decreases below
21 km/h (13 mph) when cruise is
activated, such as when climbing a
steep grade.
  Cruise control may cancel at about
15 km/h (9 mph) below the preset
speed (such as may happen when
climbing a long, steep grade).
To Increase Cruising Speed
Follow either of these procedures.
To increase speed using cruise control
switch
Press the SET
switch and hold it. Your
vehicle will accelerate. Release the switch
at the speed you want.
Press the SET
switch and release it
immediately to adjust the preset speed.
Multiple operations will increase the
preset speed according to the number of
times it is operated.
Increasing speed with a single SET
switch operation
Meter display for vehicle speed indicated
in km/h: 1 km/h (0.6 mph)
Meter display for vehicle speed indicated
in mph: 1 mph (1.6 km/h)
To increase speed using accelerator
pedal
Depress the accelerator pedal to accelerate
to the desired speed. Press the SET
or
SET
switch and release it immediately.
.B[EB@&'&&"@&EJUJPOJOEC







4–159
When Driving
Cruise Control
NOTE
Accelerate if you want to speed up
temporarily when the cruise control is
on. Greater speed will not interfere with
or change the set speed. Take your foot
off the accelerator to return to the set
speed.
To Decrease Cruising Speed
Press the SET switch and hold it. The
vehicle will gradually slow.
Release the switch at the speed you want.
Press the SET
switch and release it
immediately to adjust the preset speed.
Multiple operations will decrease the
preset speed according to the number of
times it is operated.
Decreasing speed with a single SET
switch operation
Meter display for vehicle speed indicated
in km/h: 1 km/h (0.6 mph)
Meter display for vehicle speed indicated
in mph: 1 mph (1.6 km/h)
To Resume Cruising Speed at
More Than 25 km/h (16 mph)
If some other method besides the OFF
switch was used to cancel cruising speed
(such as applying the brake pedal) and the
system is still activated, the most recent
set speed will automatically resume when
the RESUME switch is pressed.
If vehicle speed is below 25 km/h (16
mph), increase the vehicle speed up to
25 km/h (16 mph) or more and press the
RESUME switch.
To Temporarily Cancel
To temporarily cancel the system, use one
of these methods:
 


 Slightly depress the brake pedal.



(Manual transaxle)
 Depress the clutch pedal.



 Press the CANCEL switch.
If the RESUME switch is pressed when
the vehicle speed is 25 km/h (16 mph) or
higher, the system reverts to the previously
set speed.
NOTE
  If any of the following conditions
occur, the cruise control system is
temporarily cancelled.
 


 The parking brake is applied.



(Vehicles with adjustable speed
limiter)
  The ON/OFF switch for the
adjustable speed limiter is pressed.
 


(Automatic transaxle)
 The selector lever is in the P or N
position.
 


(Manual transaxle)
 The shift lever is in the neutral
position.
 
 When the cruise control system is
temporarily cancelled by even one of
the applicable cancel conditions, the
speed cannot be re-set.
 (Automatic transaxle) The cruise control cannot be
cancelled while driving in manual
mode (selector lever shifted from
D to M position). Therefore, engine
braking will not be applied even
if the transaxle is shifted down
to a lower gear. If deceleration is
required, lower the set speed or
depress the brake pedal.
.B[EB@&'&&"@&EJUJPOJOEC







4–160
When Driving
Cruise Control
To Deactivate
With adjustable speed limiter
To deactivate the system, press the ON/
OFF switch.
Without adjustable speed limiter
To deactivate the system, press the OFF
switch.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.4–161
When Driving
Tyre Pressure Monitoring System
Tyre Pressure Monitoring System *
The Tyre Pressure Monitoring System (TPMS) monitors the air pressure of all four tyres. If
the air pressure of one or more tyres is too low, the system warns the driver by indicating the
tyre pressure monitoring system warning light in the instrument cluster and operating a beep
sound. The system monitors the tyre pressures indirectly using the data sent from the ABS
wheel speed sensors.
To allow the system to operate correctly, the system needs to be initialized with the specifi ed
tyre pressure (value on the tyre pressure label). Follow the procedure and perform the
initialization.
Refer to Tyre Pressure Monitoring System Initialization on page 4-164 .
The warning light fl ashes when the system has a malfunction.
Refer to Warning Lights on page 4-41 .
ABS wheel speed sensor
.B[EB@&'&&"@&EJUJPOJOEC







4–162
When Driving
Tyre Pressure Monitoring System
CAUTION
  Each tyre, including the spare (if provided), should be checked monthly when cold
and infl ated to the infl ation pressure recommended by the vehicle manufacturer on the
vehicle placard or tyre infl ation pressure label. (If your vehicle has tyres of a different
size than the size indicated on the vehicle placard or tyre infl ation pressure label, you
should determine the proper tyre infl ation pressure for those tyres.)
 As an added safety feature, your vehicle has been equipped with a tyre pressure
monitoring system (TPMS) that illuminates a low tyre pressure telltale when one or
more of your tyres is signifi cantly under-infl ated. Accordingly, when the low tyre
pressure telltale illuminates, you should stop and check your tyres as soon as possible,
and infl ate them to the proper pressure. Driving on a signifi cantly under-infl ated tyre
causes the tyre to overheat and can lead to tyre failure. Under-infl ation also reduces
fuel effi ciency and tyre tread life, and may affect the vehicle's handling and stopping
ability.
 Please note that the TPMS is not a substitute for proper tyre maintenance, and it is the
driver's responsibility to maintain correct tyre pressure, even if under-infl ation has not
reached the level to trigger illumination of the TPMS low tyre pressure telltale.
 Your vehicle has also been equipped with a TPMS malfunction indicator to indicate
when the system is not operating properly.
 The TPMS malfunction indicator is combined with the low tyre pressure telltale.
When the system detects a malfunction, the telltale will fl ash for approximately
one minute and then remain continuously illuminated. This sequence will continue
upon subsequent vehicle start-ups as long as the malfunction exists. When the
malfunction indicator is illuminated, the system may not be able to detect or signal
low tyre pressure as intended. TPMS malfunctions may occur for a variety of reasons,
including the installation of replacement or alternate tyres or wheels on the vehicle that
prevent the TPMS from functioning properly. Always check the TPMS malfunction
telltale after replacing one or more tyres or wheels on your vehicle to ensure that the
replacement or alternate tyres and wheels allow the TPMS to continue to function
properly.
  To avoid false readings, the system samples for a little while before indicating a
problem. As a result it will not instantaneously register a rapid tyre defl ation or blow
out.
.B[EB@&'&&"@&EJUJPOJOEC